P0191 Fuel Rail Pressure Sensor Circuit Range / Performance
Diagnostic trouble codes · Vehicles built Jan 2015 – Nov 2015
Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Nov 2015 Dec 2015 – Mar 2016 Apr 2016 – Dec 2016 from Jan 2017
DESCRIPTION
The ECM monitors the internal fuel pressure of the common rail using the fuel pressure sensor, and controls the suction control valve to regulate the common rail pressure so that it reaches the target pressure determined by the ECM. The pressure sensor is a semiconductor that varies its electrical resistance when pressure is applied to its silicon chip. This sensor outputs a voltage in proportion to the common rail fuel pressure.

| DTC Detection Drive Pattern |
DTC Detection Condition |
Trouble Area |
| Idling for 1 second |
The difference between the main and sub voltage outputs of the fuel pressure sensor is 0.04 V or less, or 1.06 V or higher for 1 second or more (1 trip detection logic). |
|
| DTC No. |
Data List |
| P0191 |
|
WIRING DIAGRAM
Refer to DTC P0087 (Click here).INSPECTION PROCEDURE
- NOTICE:
- After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).
- HINT:
- Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was running or stopped, if the engine was warmed up or not, and other data from the time the malfunction occurred.
| 1. READ VALUE USING GTS (COMMON RAIL PRESSURE AND TARGET COMMON RAIL PRESSURE) |
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Common Rail Pressure and Target Common Rail Pressure.
Start the engine.
Check the change in the values for the data list items above when increasing the engine speed from idling to 3000 rpm with no load.
Result Result
Proceed to
Common Rail Pressure is always 10000 kPa or less
or
Common Rail Pressure is always 200000 kPa or higher
A
Except above
B
- HINT:
- Normally, "Common Rail Pressure" is within 5000 kPa of "Target Common Rail Pressure".
|
|
||||
| A | |
| 2. CHECK HARNESS AND CONNECTOR (FUEL PRESSURE SENSOR - ECM) |
Disconnect the fuel pressure sensor connector.
Disconnect the ECM connectors.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
D69-5 (PR) - D98-66 (PCR1)
Always
Below 1 Ω
D69-2 (PR2) - D98-114 (PCR2)
Always
Below 1 Ω
D69-1 (VCS) - D98-68 (VCS)
Always
Below 1 Ω
D69-6 (VC) - D98-69 (VCM)
Always
Below 1 Ω
D69-4 (E2) - D98-91 (E2M)
Always
Below 1 Ω
D69-3 (E2S) - D98-67 (E2S)
Always
Below 1 Ω
D69-5 (PR) or D98-66 (PCR1) - Body ground
Always
10 kΩ or higher
D69-2 (PR2) or D98-114 (PCR2) - Body ground
Always
10 kΩ or higher
D69-1 (VCS) or D98-68 (VCS) - Body ground
Always
10 kΩ or higher
D69-6 (VC) or D98-69 (VCM) - Body ground
Always
10 kΩ or higher
D69-4 (E2) or D98-91 (E2M) - Body ground
Always
10 kΩ or higher
D69-3 (E2S) or D98-67 (E2S) - Body ground
Always
10 kΩ or higher
Reconnect the fuel pressure sensor connector.
Reconnect the ECM connector.
|
|
||||
|
|
||||
| 3. REPAIR OR REPLACE HARNESS OR CONNECTOR |
Repair or replace the harness or connector.
| NEXT | |
| 4. CHECK WHETHER DTC OUTPUT RECURS (DTC P0191) |
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Clear the DTCs (Click here).
Let the engine idle for 1 second.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
Result Result
Proceed to
P0191 is output
A
No DTC is output
B
|
|
||||
| A | |
| 5. REPLACE COMMON RAIL |
Replace the common rail (Click here).
| NEXT | |
| 6. BLEED AIR FROM FUEL SYSTEM |
Bleed the air from the fuel system (Click here).
| NEXT | |
| 7. CHECK WHETHER DTC OUTPUT RECURS (DTC P0191) |
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Clear the DTCs (Click here).
Let the engine idle for 1 second.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
Result Result
Proceed to
P0191 is output
A
No DTC is output
B
|
|
||||
| A | |
| 8. REPLACE ECM |
Replace the ECM (Click here).
| NEXT | |
| 9. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Clear the DTCs (Click here).
Let the engine idle for 1 second.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Confirm that the DTC is not output again.
| NEXT | ||
| ||
