2014-2019 Hiace · Service Manual ENGINE

P0191 Fuel Rail Pressure Sensor Circuit Range / Performance

Diagnostic trouble codes · Vehicles built from Jan 2017

Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Nov 2015 Dec 2015 – Mar 2016 Apr 2016 – Dec 2016 from Jan 2017

DESCRIPTION

The ECM monitors the internal fuel pressure of the common rail using the fuel pressure sensor, and controls the suction control valve to regulate the common rail pressure so that it reaches the target pressure determined by the ECM. The pressure sensor is a semiconductor that varies its electrical resistance when pressure is applied to its silicon chip. This sensor outputs a voltage in proportion to the common rail fuel pressure.
A208460E05
P0191 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Idling for 1 second
The difference between the main and sub voltage outputs of the fuel pressure sensor is 0.04 V or less, or 1.06 V or higher for 1 second or more (1 trip detection logic).
  1. Open or short in fuel pressure sensor circuit
  2. Fuel pressure sensor (common rail)
  3. ECM
Related Data List 
DTC No.
Data List
P0191
  1. Common Rail Pressure
  2. Target Common Rail Pressure

WIRING DIAGRAM

Refer to DTC P0087 (Click here).

INSPECTION PROCEDURE

NOTICE:
After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).

HINT:
Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was running or stopped, if the engine was warmed up or not, and other data from the time the malfunction occurred.


1. READ VALUE USING GTS (COMMON RAIL PRESSURE AND TARGET COMMON RAIL PRESSURE)
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON and turn the GTS on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Common Rail Pressure and Target Common Rail Pressure.

  1. Start the engine.

  1. Check the change in the values for the data list items above when increasing the engine speed from idling to 3000 rpm with no load.

    Result 
    Result
    Proceed to
    Common Rail Pressure is always 10000 kPa or less
    or
    Common Rail Pressure is always 200000 kPa or higher
    A
    Except above
    B

    HINT:
    Normally, "Common Rail Pressure" is within 5000 kPa of "Target Common Rail Pressure".



B
Go to step 4
A


2. CHECK HARNESS AND CONNECTOR (FUEL PRESSURE SENSOR - ECM)
  1. Disconnect the fuel pressure sensor connector.

  1. Disconnect the ECM connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D69-5 (PR) - D98-66 (PCR1)
    Always
    Below 1 Ω
    D69-2 (PR2) - D98-114 (PCR2)
    Always
    Below 1 Ω
    D69-1 (VCS) - D98-68 (VCS)
    Always
    Below 1 Ω
    D69-6 (VC) - D98-69 (VCM)
    Always
    Below 1 Ω
    D69-4 (E2) - D98-91 (E2M)
    Always
    Below 1 Ω
    D69-3 (E2S) - D98-67 (E2S)
    Always
    Below 1 Ω
    D69-5 (PR) or D98-66 (PCR1) - Body ground
    Always
    10 kΩ or higher
    D69-2 (PR2) or D98-114 (PCR2) - Body ground
    Always
    10 kΩ or higher
    D69-1 (VCS) or D98-68 (VCS) - Body ground
    Always
    10 kΩ or higher
    D69-6 (VC) or D98-69 (VCM) - Body ground
    Always
    10 kΩ or higher
    D69-4 (E2) or D98-91 (E2M) - Body ground
    Always
    10 kΩ or higher
    D69-3 (E2S) or D98-67 (E2S) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the fuel pressure sensor connector.

  1. Reconnect the ECM connector.



OK
Go to step 5

NG
Go to step 3
3. REPAIR OR REPLACE HARNESS OR CONNECTOR
  1. Repair or replace the harness or connector.


NEXT


4. CHECK WHETHER DTC OUTPUT RECURS (DTC P0191)
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON and turn the GTS on.

  1. Clear the DTCs (Click here).

  1. Let the engine idle for 1 second.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the DTCs.

    Result 
    Result
    Proceed to
    P0191 is output
    A
    No DTC is output
    B



B
END
A


5. REPLACE COMMON RAIL
  1. Replace the common rail (Click here).


NEXT


6. BLEED AIR FROM FUEL SYSTEM
  1. Bleed the air from the fuel system (Click here).


NEXT


7. CHECK WHETHER DTC OUTPUT RECURS (DTC P0191)
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON and turn the GTS on.

  1. Clear the DTCs (Click here).

  1. Let the engine idle for 1 second.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the DTCs.

    Result 
    Result
    Proceed to
    P0191 is output
    A
    No DTC is output
    B



B
END
A


8. REPLACE ECM
  1. Replace the ECM (Click here).


NEXT


9. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON and turn the GTS on.

  1. Clear the DTCs (Click here).

  1. Let the engine idle for 1 second.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Confirm that the DTC is not output again.


NEXT

END


← P0191 Fuel Rail Pressure Sensor Circuit Range / Performance (Apr 2016 – Dec 2016)P0200 Injector Circuit / Open (Oct 2014 – Dec 2014) →