2014-2019 Hiace · Service Manual ENGINE

P0191 Fuel Rail Pressure Sensor Circuit Range / Performance

Diagnostic trouble codes · Vehicles built from Jan 2017

DESCRIPTION

HINT:
Refer to DTC P0087 (Click here).

P0191 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Idling for 1 second or more
The difference between the main and sub voltage outputs of the fuel pressure sensor is 0.04 V or less, or 1.06 V or higher for 1 second or more (1 trip detection logic).
  1. Open or short in fuel pressure sensor circuit
  2. Fuel pressure sensor (common rail assembly)
  3. ECM
Related Data List 
DTC No.
Data List
P0191
  1. Common Rail Pressure
  2. Target Common Rail Pressure

WIRING DIAGRAM

Refer to DTC P0087 (Click here).

INSPECTION PROCEDURE

NOTICE:
After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).

HINT:
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


1. READ VALUE USING GTS (COMMON RAIL PRESSURE AND TARGET COMMON RAIL PRESSURE)
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON and turn the GTS on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Common Rail Pressure and Target Common Rail Pressure.

  1. Start the engine.

  1. Check the change in the values for the data list items above when increasing the engine speed from idling to 3000 rpm with no load.

    Result 
    Result
    Proceed to
    Common Rail Pressure is always 10000 kPa or less
    or
    Common Rail Pressure is always 200000 kPa or higher
    A
    Except above
    B

    HINT:
    Normally, "Common Rail Pressure" is within 5000 kPa of "Target Common Rail Pressure".



B
Go to step 4
A


2. CHECK HARNESS AND CONNECTOR (FUEL PRESSURE SENSOR - ECM)
  1. Disconnect the fuel pressure sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D69-5 (PR) - D134-91 (PCR1)
    Always
    Below 1 Ω
    D69-2 (PR2) - D134-108 (PCR2)
    Always
    Below 1 Ω
    D69-1 (VCS) - D134-140 (VCS)
    Always
    Below 1 Ω
    D69-6 (VC) - D134-93 (VCM)
    Always
    Below 1 Ω
    D69-4 (E2) - D134-92 (E2M)
    Always
    Below 1 Ω
    D69-3 (E2S) - D134-107 (E2S)
    Always
    Below 1 Ω
    D69-5 (PR) or D134-91 (PCR1) - Body ground and other terminals
    Always
    10 kΩ or higher
    D69-2 (PR2) or D134-108 (PCR2) - Body ground and other terminals
    Always
    10 kΩ or higher
    D69-1 (VCS) or D134-140 (VCS) - Body ground and other terminals
    Always
    10 kΩ or higher
    D69-6 (VC) or D134-107 (VCM) - Body ground and other terminals
    Always
    10 kΩ or higher

  1. Reconnect the fuel pressure sensor connector.

  1. Reconnect the ECM connector.



OK
Go to step 5

NG
Go to step 3
3. REPAIR OR REPLACE HARNESS OR CONNECTOR
  1. Repair or replace the harness or connector.


NEXT


4. CHECK WHETHER DTC OUTPUT RECURS (DTC P0191)
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON and turn the GTS on.

  1. Clear the DTCs (Click here).

  1. Let the engine idle for 1 second or more.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the DTCs.

    Result 
    Result
    Proceed to
    DTC P0191 is output
    A
    No DTC is output
    B



B
END
A


5. REPLACE COMMON RAIL ASSEMBLY
  1. Replace the common rail assembly (Click here).


NEXT


6. BLEED AIR FROM FUEL SYSTEM
  1. Bleed the air from the fuel system (Click here).


NEXT


7. CHECK WHETHER DTC OUTPUT RECURS (DTC P0191)
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON and turn the GTS on.

  1. Clear the DTCs (Click here).

  1. Let the engine idle for 1 second or more.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the DTCs.

    Result 
    Result
    Proceed to
    DTC P0191 is output
    A
    No DTC is output
    B



B
END
A


8. REPLACE ECM
  1. Replace the ECM (Click here).


NEXT


9. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON and turn the GTS on.

  1. Clear the DTCs (Click here).

  1. Let the engine idle for 1 second or more.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Confirm that the DTC is not output again.


NEXT

END


← P0122 Throttle / Pedal Position Sensor / Switch "A" Circuit Low Input (+ P0123) (from Jan 2017)P0201 Injector Circuit / Open - (Cylinder 1) (+ P0202, P0203, P0204, P062D) (from Jan 2017) →