P0122 Throttle / Pedal Position Sensor / Switch "A" Circuit Low Input
Diagnostic trouble codes · Vehicles built from Jan 2017
Also covers:
- P0123 Throttle / Pedal Position Sensor / Switch "A" Circuit High Input
DESCRIPTION
The throttle position sensor is mounted on the diesel throttle body assembly and detects the opening angle of the throttle valve. This sensor is an electronic sensor and uses Hall-effect elements.When the throttle valve is fully closed, a voltage of approximately 0.4 to 1.0 V is applied to terminal VLU of the ECM. The voltage applied to terminal VLU of the ECM increases in proportion to the opening angle of the throttle valve and becomes approximately 3.6 to 4.2 V when the throttle valve is fully opened.
The ECM determines the vehicle driving conditions from the signals input to its VLU terminal. The data is one of the pieces of information used for EGR control, etc.


| DTC Detection Drive Pattern |
DTC Detection Condition |
Trouble Area |
| Ignition switch ON for 3 seconds or more |
Throttle position sensor output (VLU) is below 0.2 V for 3 seconds (1 trip detection logic). |
|
| DTC Detection Drive Pattern |
DTC Detection Condition |
Trouble Area |
| Ignition switch ON for 3 seconds or more |
Throttle position sensor output (VLU) is higher than 4.8 V for 3 seconds (1 trip detection logic). |
|
- HINT:
- If DTC P0122 and/or P0123 is stored, the following symptoms may appear:
- - Intake booming noise
- - Black smoke
- - Lack of power
- - Vibration at engine stop
- - Turbo overspeed, turbo damage
MONITOR DESCRIPTION
When the output voltage of the throttle position sensor deviates from the normal operating range (between 0.2 V and 4.8 V) for more than 3 seconds, the ECM interprets this as a malfunction of the sensor circuit and illuminates the MIL.

WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).
- HINT:
- Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
| 1. CHECK DTC OUTPUT |
Connect the GTS to the DLC3.
Clear the DTCs (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON for 3 seconds or more.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Confirm that the DTC is not output again.
- Result:
Result
Proceed to
DTCs are not output
A
DTC P0122 or P0123 is output
B
|
|
||||
| A | |
| 2. CHECK HARNESS AND CONNECTOR (THROTTLE POSITION SENSOR - ECM) |
Disconnect the diesel throttle body assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
D119-5 (VTA) - D134-125 (VLU)
Always
Below 1 Ω
D119-6 (E2) - D134-124 (EVLU)
Always
Below 1 Ω
D119-5 (VTA) or D134-125 (VLU) - Body ground and other terminals
Always
10 kΩ or higher
D119-6 (E2) or D134-124 (EVLU) - Body ground and other terminals
Always
10 kΩ or higher
Reconnect the diesel throttle body assembly connector.
Reconnect the ECM connector.
|
|
||||
| OK | |
| 3. CHECK HARNESS AND CONNECTOR |
Disconnect the diesel throttle body assembly connector.

Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
D119-3 (VC) - D119-6 (E2)
Ignition switch ON
4.5 to 5.5 V
Text in Illustration *a
Front view of wire harness connector
(to Diesel Throttle Body Assembly)
Reconnect the throttle position sensor connector.
|
|
||||
| OK | |
| 4. CHECK ECM (CHECK RESISTANCE) |
Disconnect the diesel throttle body assembly connector.

Measure the resistance according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
D119-3 (VC) - D119-5 (VTA)
Ignition switch off
No short or no open
D119-5 (VTA) - D119-6 (E2)
Text in Illustration *a
Front view of wire harness connector
(to Diesel Throttle Body Assembly)
Reconnect the diesel throttle body assembly connector.
|
|
||||
| OK | |
| 5. REPLACE DIESEL THROTTLE BODY ASSEMBLY |
Replace the diesel throttle body assembly (Click here).
|
|
||||
| 6. REPLACE ECM |
Replace the ECM (Click here).
|
|
||||
| 7. REPAIR OR REPLACE HARNESS OR CONNECTOR |
Repair or replace the harness or connector.
|
|
||||
| 8. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
Connect the GTS to the DLC3.
Clear the DTCs (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON for 3 seconds or more.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Confirm that the DTC is not output again.
| NEXT | ||
| ||
