2014-2019 Hiace · Service Manual ENGINE

P0405 Exhaust Gas Recirculation Sensor "A" Circuit Low

Diagnostic trouble codes · Vehicles built Dec 2015 – Mar 2016

Also covers:

Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Nov 2015 Dec 2015 – Mar 2016 Apr 2016 – Dec 2016 from Jan 2017

DESCRIPTION

The EGR valve position sensor is mounted on the EGR valve and used for detecting the EGR valve angle. The EGR valve angle detected by the sensor is sent to the ECM as feedback. The ECM then regulates the EGR valve angle in accordance with engine running conditions.
P0405 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Ignition switch ON for 5 seconds
EGR valve position sensor output voltage is less than 0.2 V for 2 seconds.
(1 trip detection logic)
  1. Open or short in EGR valve position sensor circuit
  2. Electric EGR control valve assembly (EGR valve position sensor)
  3. ECM
P0406 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Ignition switch ON for 5 seconds
EGR valve position sensor output voltage is higher than 4.8 V for 2 seconds.
(1 trip detection logic)
  1. Open or short in EGR valve position sensor circuit
  2. Electric EGR control valve assembly (EGR valve position sensor)
  3. ECM

MONITOR DESCRIPTION

When the output voltage of the EGR valve position sensor deviates from the normal operating range of 0.1 to 4.9 V for more than 5 seconds, the ECM interprets this as a malfunction of the sensor circuit and illuminates the MIL.

WIRING DIAGRAM

Refer to DTC P042E (Click here).

INSPECTION PROCEDURE

NOTICE:
  1. After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).
  2. After replacing the fuel supply pump assembly, the ECM needs initialization (Click here).
  3. After replacing an injector assembly, the ECM needs registration (Click here).

HINT:
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


1. CHECK HARNESS AND CONNECTOR (EGR VALVE POSITION SENSOR - ECM)
  1. Disconnect the electric EGR control valve assembly connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    s1-3 (VC) - D99-75 (VCPX)
    Always
    Below 1 Ω
    s1-2 (VTA) - D99-115 (EGRA)
    Always
    Below 1 Ω
    s1-1 (E2) - D99-92 (EEGL)
    Always
    Below 1 Ω
    s1-3 (VC) or D99-75 (VCPX) - Body ground
    Always
    10 kΩ or higher
    s1-2 (VTA) or D99-115 (EGRA) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the electric EGR control valve assembly connector.

  1. Reconnect the ECM connector.



NG
Go to step 6
OK


2. CHECK HARNESS AND CONNECTOR (POWER SOURCE)

  1. A242722E09
    Disconnect the electric EGR control valve assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    s1-3 (VC) - s1-1 (E2)
    Ignition switch ON
    4.5 to 5.5 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Electric EGR control valve assembly)

  1. Reconnect the electric EGR control valve assembly connector.



NG
Go to step 5
OK


3. REPLACE ELECTRIC EGR CONTROL VALVE ASSEMBLY
  1. Replace the electric EGR control valve assembly (Click here).


NEXT


4. CHECK WHETHER DTC OUTPUT RECURS (P0405 OR P0406)
  1. Connect the GTS to the DLC3.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch to ON for 5 seconds or more.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Confirm that the DTC is not output again.

    OK:
    DTC is not output again.



NG
Go to step 5
OK

END

5. REPLACE ECM
  1. Replace the ECM (Click here).



NEXT
Go to step 7
6. REPAIR OR REPLACE HARNESS OR CONNECTOR
  1. Repair or replace the harness or connector.


NEXT


7. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. Connect the GTS to the DLC3.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch to ON for 5 seconds or more.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Confirm that the DTC is not output again.


NEXT

END


← P0405 Exhaust Gas Recirculation Sensor "A" Circuit Low (+ P0406) (Jan 2015 – Nov 2015)P0405 Exhaust Gas Recirculation Sensor "A" Circuit Low (+ P0406) (Apr 2016 – Dec 2016) →