2014-2019 Hiace · Service Manual ENGINE

P0627 Fuel Pump Control Circuit / Open

Diagnostic trouble codes · Vehicles built from Jan 2017

DESCRIPTION

P0627 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Idling for 1 second or more
Even though the CPU (command area inside the ECU) is outputting the pre-stroke control valve operation duty, the output monitor signal is absent for 0.5 seconds (1 trip detection logic).
  1. Open or short in pre-stroke control valve circuit
  2. Fuel supply pump assembly
  3. ECM
Related Data List 
DTC No.
Data List
P0627
  1. Common Rail Pressure
  2. Target Common Rail Pressure

HINT:
  1. For more information on the fuel supply pump assembly (pre-stroke control valve) and common rail system, refer to System Description (Click here).
  2. When DTC P0627 is stored, check the internal fuel pressure of the common rail by entering the following menus on the GTS: Powertrain / Engine and ECT / Data List / Common Rail Pressure.
    Under a stable operating condition such as idling, Common Rail Pressure is within 5000 kPa of Target Common Rail Pressure.


WIRING DIAGRAM

A348538E08

INSPECTION PROCEDURE

NOTICE:
After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).

HINT:
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


1. INSPECT PRE-STROKE CONTROL VALVE (FUEL SUPPLY PUMP ASSEMBLY)
  1. Inspect the pre-stroke control valve (Click here).



NG
Go to step 4
OK


2. CHECK HARNESS AND CONNECTOR (PRE-STROKE CONTROL VALVE - ECM)
  1. Disconnect the pre-stroke control valve connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D117-1 - D134-59 (PCV+)
    Always
    Below 1 Ω
    D117-2 - D134-60 (PCV-)
    Always
    Below 1 Ω
    D117-1 or D134-59 (PCV+) - Body ground and other terminals
    Always
    10 kΩ or higher
    D117-2 or D134-60 (PCV-) - Body ground and other terminals
    Always
    10 kΩ or higher

  1. Reconnect the pre-stroke control valve connector.

  1. Reconnect the ECM connector.



NG
Go to step 7
OK


3. CHECK WHETHER DTC OUTPUT RECURS
  1. Connect the GTS to the DLC3

  1. Turn the ignition switch to ON and turn the GTS on.

  1. Clear the DTCs (Click here).

  1. Start the engine and idle it for 1 second or more.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the DTCs.

    Result 
    Result
    Proceed to
    No DTC is output
    A
    DTC P0627 is output
    B



B
Go to step 6
A

END

4. REPLACE FUEL SUPPLY PUMP ASSEMBLY (PRE-STROKE CONTROL VALVE)
  1. Replace the fuel supply pump assembly (Click here).


NEXT


5. BLEED AIR FROM FUEL SYSTEM
  1. Bleed the air from the fuel system (Click here).


NEXT


6. REPLACE ECM
  1. Replace the ECM (Click here).



NEXT
Go to step 8
7. REPAIR OR REPLACE HARNESS OR CONNECTOR
  1. Repair or replace the harness or connector.


NEXT


8. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. Connect the GTS to the DLC3.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off for 30 seconds or more.

  1. Start the engine and idle it for 1 second or more.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Confirm that the DTC is not output again.


NEXT

END


← P0617 Starter Relay Circuit High (from Jan 2017)P062F Internal Control Module EEPROM Error (from Jan 2017) →