2014-2019 Hiace · Service Manual ENGINE

REMOVAL

Removal / installation · Vehicles built from Jan 2017

NOTICE:
  1. When replacing the parts in the following chart (A), replace the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly with new ones.
    Replaced Parts (A)
    Pipes Requiring New Replacement
    1. Injector assembly (including shuffling the injector assemblies between the cylinders)
    2. Common rail assembly
    3. Cylinder head sub-assembly
    1. No. 1 injection pipe sub-assembly
    2. No. 2 injection pipe sub-assembly
    Supply pump assembly
    Fuel inlet pipe sub-assembly
    1. Common rail assembly
    2. Cylinder block sub-assembly
    3. Cylinder head sub-assembly
    4. Cylinder head gasket
    5. Timing chain case assembly
    1. No. 1 injection pipe sub-assembly
    2. No. 2 injection pipe sub-assembly
    3. Fuel inlet pipe sub-assembly
  2. After removing the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly, clean them with a brush and compressed air.
  3. The injector assembly is a precision instrument. Do not use the injector assembly if it is struck or dropped.
  4. Make sure foreign matter does not enter the fuel path.


1. PRECAUTION

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).


2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


3. REMOVE INTAKE MANIFOLD
(Click here)

4. DISCONNECT NO. 1 AIR HOSE

  1. A391874
    Slide the clamp and disconnect the No. 1 air hose from the No. 1 air tube.


5. REMOVE NO. 4 AIR HOSE

A398587
  1. Slide the 2 clips and disconnect the oil return hose.

  1. Loosen the 2 hose clamps and remove the No. 4 air hose.


6. DISCONNECT NO. 1 RADIATOR HOSE

  1. A398412
    Slide the clip and disconnect the No. 1 radiator hose from the water inlet.


7. REMOVE FAN AND GENERATOR V BELT

  1. A396825E01
    While turning the V-ribbed belt tensioner assembly clockwise, align the service holes of the V-ribbed belt tensioner assembly, and then insert a pin with a diameter of 5.0 mm (0.197 in.) into the service holes to fix the V-ribbed belt tensioner assembly in place.
    Text in Illustration 
    *a
    Service Hole
    *b
    Pin

  1. Remove the fan and generator V belt.


8. REMOVE V-RIBBED BELT TENSIONER ASSEMBLY

  1. A339579
    Remove the 3 bolts and V-ribbed belt tensioner assembly from the timing chain cover sub-assembly.


9. REMOVE NO. 2 FUEL HOSE
  1. Slide the 2 clips and remove the No. 2 fuel hose from the supply pump assembly and No. 3 nozzle leakage pipe assembly.


10. REMOVE NO. 1 FUEL HOSE

A353389
  1. Slide the 2 clips and remove the No. 1 fuel hose from the supply pump assembly and No. 2 fuel pipe.


11. REMOVE FUEL INJECTION PUMP COVER SUB-ASSEMBLY

A353390
  1. Remove the fuel injection pump cover sub-assembly from the supply pump assembly.


12. REMOVE FUEL PUMP MOTOR WIRE

A401178
  1. Disconnect the fuel pump motor wire connector and remove the fuel pump motor wire.


13. REMOVE TIMING CHAIN COVER PLATE

A344936
  1. Remove the 3 bolts and timing chain cover plate.

  1. Remove the gasket.


14. REMOVE SUPPLY PUMP ASSEMBLY

A354097

NOTICE:
  1. Do not hold the supply pump assembly by the parts indicated by the arrows in the illustration.
  2. With SST set, do not turn the crankshaft more than a half rotation.

  1. A401173E01
    Align the timing mark of the crankshaft pulley sub-assembly and timing chain cover by rotating the crankshaft clockwise.
    Text in Illustration 
    *a
    Timing Mark

  1. A398344E01
    Using SST, hold the crankshaft pulley assembly and loosen the fuel supply pump shaft nut.
    Text in Illustration 
    *a
    Hold
    V100135
    Turn
    SST
    09213-58014   (91551-80840)
    09330-00021  

    NOTICE:
    Do not excessively loosen the supply pump shaft nut, otherwise SST cannot be installed.

    HINT:
    Rotate the supply pump shaft nut once to loosen it.

  1. A353387
    Loosen the 3 nuts from the supply pump assembly.

    NOTICE:
    Do not completely remove the nuts. Otherwise, the supply pump assembly may fall off.

  1. A344938E01
    Install SST with the 3 bolts.
    SST
    09241-11010  

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

    NOTICE:
    Install SST with the bolts included with SST.

    HINT:

    1. A347063E02
    2. Make sure that the installation direction of SST is as shown in the illustration.
    3. Align the hexagonal portion of SST with the supply pump shaft nut to install SST.
      Text in Illustration 
      *a
      Engine Front Side
      *b
      Engine Rear Side
      *c
      SST Hexagonal Portion

  1. A344941
    Remove the 2 bolts and No. 1 fuel pump bracket from the supply pump assembly and cylinder block sub-assembly.

  1. A398345E01
    Install the handle to SST. While holding the crankshaft pulley assembly in place with the crankshaft holding tool, turn the handle in the counterclockwise direction to disconnect the supply pump assembly.
    SST
    09213-58014   (91551-80840)
    09241-11010  
    09330-00021  
    Text in Illustration 
    *a
    Hold
    V100135
    Turn

  1. Remove the 3 nuts and supply pump assembly from the timing chain case assembly.

  1. A347064
    Remove the O-ring from the supply pump assembly.

← COMPONENTS (from Jan 2017)INSPECTION (from Jan 2017) →