2014-2019 Hiace · Service Manual ENGINE

Fuel Pump Control Circuit

Circuit diagnosis · Vehicles built Oct 2014 – Dec 2014

DESCRIPTION

When the engine is cranked, the starter (ST) relay drive signal output from the ignition switch is input into the STA terminal of the ECM, and the NE signal generated by the crankshaft position sensor is input into the NE+ terminal. The ECM determines that the engine is cranked, and turns transistor in the ECM internal circuit on. Current flows to the circuit opening (C/OPN) relay by turning transistor on.
Then, the fuel pump operates.
While the NE signal is input into the ECM and the engine is running, the ECM turns transistor on continuously.

WIRING DIAGRAM

A318857E01

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses of circuits related to this system before performing the following inspection procedure.


1. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE FUEL PUMP / SPEED)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the intelligent tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.

  1. Check whether the fuel pump operating sound occurs when performing the Active Test on the intelligent tester.

    OK:
    Fuel pump operating sound occurs.



NG
Go to step 4
OK


2. READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the intelligent tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.

  1. Check the result when the ignition switch is turned to ON and START.

    OK:
    Ignition Switch Position
    Starter Signal
    ON
    OFF
    START
    ON



NG
REPAIR OR REPLACE STARTING SYSTEM
OK


3. READ VALUE USING INTELLIGENT TESTER (ENGINE SPEED)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the intelligent tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Engine Speed.

  1. Read the values displayed on the intelligent tester while cranking the engine.

    OK:
    Values are displayed continuously.



NG
REPAIR OR REPLACE CRANKSHAFT POSITION SENSOR CIRCUIT
OK

REPLACE ECM (Click here)

4. CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - ECM)
  1. Disconnect the ECM connector.

  1. Disconnect the No. 1 integration relay connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    B71-19 (FC) - 10A-3
    Always
    Below 1 Ω
    B71-19 (FC) or 10A-3 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. INSPECT NO. 1 INTEGRATION RELAY (C/OPN RELAY)
  1. Remove the No. 1 integration relay from the No. 1 engine room relay block.

  1. A318873E01
    Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    10A-2 - Body ground
    Ignition switch off
    Below 1 V
    10A-4 - Body ground
    10A-2 - Body ground
    Ignition switch ON
    11 to 14 V
    10A-4 - Body ground
    Engine cranking

    Text in Illustration 
    *a
    Component with harness connected
    (No. 1 Integration Relay)



NG
Go to step 8
OK


6. CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - FUEL PUMP - BODY GROUND)
  1. Check the harness and connectors between the No. 1 integration relay and fuel pump.

    1. Remove the No. 1 integration relay from the No. 1 engine room relay block.

    2. Disconnect the fuel pump connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      h2-4 - 10A-4
      Always
      Below 1 Ω
      h2-4 or 10A-4 - Body ground
      Always
      10 kΩ or higher

  1. Check the harness and connectors between the fuel pump and body ground.

    1. Disconnect the fuel pump connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      h2-5 - Body ground
      Always
      Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7. INSPECT FUEL PUMP
  1. Inspect the fuel pump (Click here).



NG
REPLACE FUEL PUMP (Click here)
OK

REPLACE ECM (Click here)

8. INSPECT NO. 1 INTEGRATION RELAY (C/OPN)
  1. Inspect the No. 1 integration relay (C/OPN) (Click here).



NG
REPLACE NO. 1 INTEGRATION RELAY
OK


9. CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - NO. 2 INTEGRATION RELAY)
  1. Remove the No. 1 integration relay from the No. 1 engine room relay block.

  1. Remove the No. 2 integration relay from the instrument panel relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    12B-7 - 10A-2
    Always
    Below 1 Ω
    10A-1 - 10A-8
    Always
    Below 1 Ω
    12B-7 or 10A-2 - Body ground
    Always
    10 kΩ or higher
    10A-1 or 10A-8 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

GO TO ECM POWER SOURCE CIRCUIT (Click here)


← VC Output Circuit (Oct 2014 – Dec 2014)Fuel Injector Circuit (Oct 2014 – Dec 2014) →