2014-2019 Hiace · Service Manual BODY ELECTRICAL

No Answer-back

Circuit diagnosis · Vehicles built from Jan 2017

Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Dec 2016 from Jan 2017

DESCRIPTION

In some cases, wireless door lock control functions are normal but the hazard warning light answer-back function does not operate. In such cases, hazard warning light signal circuit may be malfunctioning.

WIRING DIAGRAM

E290557E03

INSPECTION PROCEDURE


1. CHECK WIRELESS DOOR LOCK CONTROL FUNCTIONS
  1. Check that the wireless door lock functions using the door control transmitter assembly (Click here).

    OK:
    The wireless door lock functions using the door control transmitter assembly are normally.



NG
GO TO OTHER FLOWCHART (Only Wireless Control Function is Inoperative) (Click here)
OK


2. CHECK HAZARD WARNING LIGHTS
  1. Check that the hazard warning lights blink when the hazard warning signal switch assembly is pressed.

    OK:
    Hazard warning lights flash continuously.



NG
GO TO LIGHTING SYSTEM (Click here)
OK


3. INSPECT FRONT DOOR LOCK ASSEMBLY (UNLOCK DETECTION SWITCH)
  1. *1: for LHD
  2. *2: for RHD
  1. Remove the front door lock assembly LH*1 or RH*2 (Click here)

  1. Inspect the front door lock assembly LH*1 or RH*2 (Click here)



NG
REPLACE FRONT DOOR LOCK ASSEMBLY (Click here)
OK


4. CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY [BODY ECU] - FRONT DOOR LOCK ASSEMBLY AND BODY GROUND)
  1. Disconnect the H7 instrument panel junction block assembly (body ECU) connector.

  1. Disconnect the L1*1 or K1*2 front door lock assembly connector.

    1. *1: for LHD
    2. *2: for RHD

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LHD:
    Tester Connection
    Condition
    Specified Condition
    H7-4 (LSWD) - L1-7(LSSR)
    Always
    Below 1 Ω
    L1-8 (E) - Body ground
    Always
    Below 1 Ω
    H7-4 (LSWD) or L1-7(LSSR) - Body ground
    Always
    10 kΩ or higher
    for RHD:
    Tester Connection
    Condition
    Specified Condition
    H7-4 (LSWD) - K1-7(LSSR)
    Always
    Below 1 Ω
    K1-8 (E) - Body ground
    Always
    Below 1 Ω
    H7-4 (LSWD) or K1-7(LSSR) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY [BODY ECU] - COMBINATION METER ASSEMBLY)
  1. Disconnect the H7 instrument panel junction block assembly connector.

  1. Disconnect the H20 combination meter assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    H7-6 (HAZ) - H20-26 (HAZ)
    Always
    Below 1 Ω
    H7-6 (HAZ) or H20-26 (HAZ) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (BODY ECU)


← No Answer-back (Jan 2015 – Dec 2016)PRECAUTION (from Oct 2014) →