C146E Open in ABS Solenoid Relay Circuit
Diagnostic trouble codes · Vehicles built Jan 2015 – Mar 2016
Also covers:
- C146F Short in ABS Solenoid Relay Circuit
Versions by build date: Jan 2015 – Mar 2016 Apr 2016 – Dec 2016 Jan 2017 – Nov 2017 from Dec 2017
DESCRIPTION
The ABS solenoid relay supplies power to the ABS solenoid and TRC solenoid.The solenoid relay is turned on 1.5 seconds after the ignition switch is turned to ON, and is turned off if an open or short in the solenoid is detected by the self-diagnosis performed when the engine starts running.
The ABS solenoid relay is housed in the skid control ECU in the actuator assembly.
| DTC No. |
DTC Detection Condition |
Trouble Area |
| C146E |
Either of the following is detected:
|
|
| C146F |
Immediately after ignition switch turned to ON and solenoid relay is OFF, relay contact is ON continuously for 4.5 seconds or more. |
Skid control ECU (Brake actuator assembly) |
WIRING DIAGRAM
Refer to DTCs C1225, C1468, C1469, C146A and C146B (Click here).INSPECTION PROCEDURE
- NOTICE:
- When replacing the skid control ECU (brake actuator assembly), perform zero point calibration and store system information (Click here).
- Inspect the fuses for circuits related to this system before performing the following inspection procedure.
- When replacing the skid control ECU (brake actuator assembly), perform zero point calibration and store system information (Click here).
- HINT:
- When C1241 and/or C1417 is output together with C146E and/or C146F, inspect and repair the trouble areas indicated by C1241 and/or C1417 first (Click here and/or Click here).
| 1. CHECK TERMINAL VOLTAGE (+BS TERMINAL) |
Turn the ignition switch off.
Make sure that there is no looseness in the locking part and connecting part of the connectors.

Disconnect the B92 skid control ECU (brake actuator assembly) connector.
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Condition
Specified Condition
B92-38 (+BS) - Body ground
Always
11 to 14 V
Text in Illustration *a
Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))
|
|
||||
| OK | |
| 2. CHECK HARNESS AND CONNECTOR (GND1 TERMINAL) |
Measure the resistance according to the value(s) in the table below.

- Standard Resistance:
Tester Connection
Condition
Specified Condition
B92-25 (GND1) - Body ground
Always
Below 1 Ω
Text in Illustration *a
Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))
|
|
||||
| OK | |
| 3. RECONFIRM DTC |
- These codes are detected when a problem is determined in the skid control ECU (brake actuator assembly).
- The solenoid circuits are in the skid control ECU (brake actuator assembly).
- Therefore, solenoid circuit inspection and solenoid unit inspection cannot be performed.
- Be sure to check if any DTCs are output before replacing the skid control ECU (brake actuator assembly).
Reconnect the B92 skid control ECU (brake actuator assembly) connector.
Clear the DTCs (Click here).
Turn the ignition switch off.
Start the engine.
Drive the vehicle at a speed of 20 km/h (12 mph) or more for 30 seconds or more.
Check if the same DTC is recorded (Click here).
- Result:
Result
Proceed to
DTC C146E and C146F are not output
A
DTC C146E and/or C146F are output
B
- HINT:
- If a speed signal of 6 km/h (4 mph) or more is input to the skid control ECU (brake actuator assembly), with the ignition switch ON and the stop light switch off, the ECU performs self-diagnosis of the motor and solenoid circuits.
- If the normal system code is output (the trouble code is not output), slightly jiggle the connectors, wire harness, and fuses of the skid control ECU (brake actuator assembly). Make sure that no DTCs are output.
- If any DTCs are output while jiggling a connector or wire harness from the skid control ECU (brake actuator assembly), inspect and repair the connector or wire harness.
- The DTCs were probably output due to a bad connection of the connector terminal.
- If a speed signal of 6 km/h (4 mph) or more is input to the skid control ECU (brake actuator assembly), with the ignition switch ON and the stop light switch off, the ECU performs self-diagnosis of the motor and solenoid circuits.
|
|
||||
| A | ||
| ||
