2014-2019 Hiace · Service Manual BRAKE

C146E Open in ABS Solenoid Relay Circuit

Diagnostic trouble codes · Vehicles built from Dec 2017

Also covers:

Versions by build date: Jan 2015 – Mar 2016 Apr 2016 – Dec 2016 Jan 2017 – Nov 2017 from Dec 2017

DESCRIPTION

The ABS solenoid relay supplies power to the ABS solenoid and TRC solenoid.
The solenoid relay is turned on 1.5 seconds after the ignition switch is turned to ON, and is turned off if an open or short in the solenoid is detected by the self-diagnosis performed when the engine starts running.
The ABS solenoid relay is housed in the skid control ECU in the actuator assembly.
DTC No.
DTC Detection Condition
Trouble Area
C146E
Either of the following is detected:
  1. When voltage at terminal +BS is 9.5 V or higher and solenoid relay is ON, relay contact is OFF continuously for 0.22 seconds or more.
  2. When solenoid relay is turned on and voltage at +BS terminal is below 9.5 V, relay contact does not turn on after 0.22 seconds or more.
  1. ABS SOL fuse
  2. Wire harness or connector
  3. Skid control ECU (Brake actuator assembly)
C146F
Immediately after ignition switch turned to ON and solenoid relay is OFF, relay contact is ON continuously for 4.5 seconds or more.
Skid control ECU (Brake actuator assembly)

WIRING DIAGRAM

Refer to DTCs C1225, C1468, C1469, C146A and C146B (Click here).

INSPECTION PROCEDURE

NOTICE:
  1. When replacing the skid control ECU (brake actuator assembly), perform zero point calibration and store system information (Click here).
  2. Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
When C1241 and/or C1417 is output together with C146E and/or C146F, inspect and repair the trouble areas indicated by C1241 and/or C1417 first (Click here and/or Click here).


1. CHECK TERMINAL VOLTAGE (+BS TERMINAL)


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (+BS CIRCUIT)
OK


2. CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (GND1 CIRCUIT)
OK


3. RECONFIRM DTC
  1. These codes are detected when a problem is determined in the skid control ECU (brake actuator assembly).
  2. The solenoid circuits are in the skid control ECU (brake actuator assembly).
  3. Therefore, solenoid circuit inspection and solenoid unit inspection cannot be performed.
  4. Be sure to check if any DTCs are output before replacing the skid control ECU (brake actuator assembly).
  1. Reconnect the B92 skid control ECU (brake actuator assembly) connector.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Start the engine.

  1. Drive the vehicle at a speed of 20 km/h (12 mph) or more for 30 seconds or more.

  1. Check if the same DTC is recorded (Click here).

    Result:
    Result
    Proceed to
    DTC C146E and C146F are not output
    A
    DTC C146E and/or C146F are output
    B

    HINT:
    1. If a speed signal of 6 km/h (4 mph) or more is input to the skid control ECU (brake actuator assembly), with the ignition switch ON and the stop light switch off, the ECU performs self-diagnosis of the motor and solenoid circuits.
    2. If the normal system code is output (the trouble code is not output), slightly jiggle the connectors, wire harness, and fuses of the skid control ECU (brake actuator assembly). Make sure that no DTCs are output.
    3. If any DTCs are output while jiggling a connector or wire harness from the skid control ECU (brake actuator assembly), inspect and repair the connector or wire harness.
    4. The DTCs were probably output due to a bad connection of the connector terminal.



B
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)
A

USE SIMULATION METHOD TO CHECK (Click here)


← C146E Open in ABS Solenoid Relay Circuit (+ C146F) (Jan 2017 – Nov 2017)U0073 Control Module Communication Bus OFF (+ U0100, U0124, U0126) (Jan 2015 – Mar 2016) →