2014-2019 Hiace · Service Manual ENGINE

REASSEMBLY

Removal / installation · Vehicles built from Jan 2017


1. INSTALL GENERATOR DRIVE END FRAME BEARING

  1. A398567E01
    Using SST and a press, press in a new generator drive end frame bearing.
    SST
    09950-60010   (09951-00470)
    09950-70010   (09951-07100)

  1. A398568E01
    Fit the tabs on the retainer plate into the cutouts on the drive end frame to install the retainer plate.
    Text in Illustration 
    *a
    Tab
    *b
    Cutout

  1. Install the retainer plate with the 4 screws.

    Torque:
    2.3 N*m{ 23 kgf*cm , 20 in.*lbf }


2. INSTALL GENERATOR ROTOR ASSEMBLY
  1. Place the generator drive end frame on the generator pulley with clutch.

  1. Install the generator rotor assembly to the generator drive end frame.


3. INSTALL GENERATOR BEARING COVER PACKING

NOTICE:
A new generator coil assembly comes with a generator bearing cover packing. Therefore, it is not necessary to install a new generator bearing cover packing when installing a new generator coil assembly.

  1. A398625E01
    Install a new generator bearing cover packing to the generator coil assembly.
    Text in Illustration 
    *a
    Protrusion
    *b
    Groove

    NOTICE:
    Align the protrusion of the generator bearing cover packing with the groove of the generator coil assembly when installing.


4. INSTALL GENERATOR COIL ASSEMBLY

  1. A398569E01
    Using a 21 mm deep socket wrench and press, slowly press on the generator coil assembly.
    Text in Illustration 
    *a
    21 mm Deep Socket Wrench

  1. Install the generator coil assembly with the 4 through bolts.

    Torque:
    5.6 N*m{ 57 kgf*cm , 50 in.*lbf }


5. INSTALL GENERATOR BRUSH HOLDER ASSEMBLY

  1. A079315E27
    While pushing the 2 brushes into the generator brush holder assembly, insert a pin with a diameter of 1.0 mm (0.0394 in.) into the brush holder hole.
    Text in Illustration 
    *a
    Pin

  1. A398570E01
    Install the generator brush holder assembly to the generator coil assembly with the 2 screws.

    Torque:
    1.8 N*m{ 18 kgf*cm , 16 in.*lbf }

    Text in Illustration 
    *a
    Pin

  1. Pull out the pin from the generator brush holder assembly.


6. INSTALL GENERATOR REAR END COVER
  1. Install the generator rear end cover to the generator coil assembly with the 3 bolts.

    Torque:
    4.6 N*m{ 47 kgf*cm , 41 in.*lbf }


7. INSTALL TERMINAL INSULATOR
  1. Install the terminal insulator to the generator coil assembly.

    NOTICE:
    Make sure that the terminal insulator is installed with the correct orientation.


8. INSTALL GENERATOR PULLEY WITH CLUTCH
  1. Mount the generator assembly in the vise between aluminum plates.

  1. Temporarily install the generator pulley with clutch by hand.

  1. A398572E01
    Install SST A and SST B to the generator pulley with clutch as shown in the illustration.
    SST
    09820-63021  
    Text in Illustration 
    *a
    Generator Rotor Shaft

    NOTICE:
    Securely attach SST to the generator pulley with clutch and generator rotor shaft.

  1. A398573E01
    Using a wrench to hold SST A, turn SST B clockwise to tighten the generator pulley with clutch.

    Torque:
    Specified tightening torque:
    110.5 N*m{ 1127 kgf*cm , 81 ft.*lbf }

    Text in Illustration 
    *a
    Hold
    *b
    Torque Wrench Fulcrum Length
    *c
    SST Fulcrum Length
    V100135
    Turn

    NOTICE:
    Be careful as the generator pulley with clutch or generator rotor shaft may be damaged if the position of SST is not securely maintained while performing this operation.

    HINT:
    1. Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.
      (Click here)
    2. When using SST (fulcrum length of 100 mm (3.94 in.)) + torque wrench (fulcrum length of 400 mm (15.8 in.)):
      88.4 N*m (901 kgf*cm, 65 ft.*lbf)

  1. Remove SST from the generator assembly.

  1. Check that the generator pulley with clutch rotates smoothly.

  1. Remove the generator assembly from the vise.


9. INSTALL GENERATOR PULLEY CAP
  1. Install a new generator pulley cap to the generator pulley with clutch.

← INSPECTION (from Jan 2017)INSTALLATION (from Jan 2017) →