Power Source Mode does not Change to ON (IG and ACC)
Circuit diagnosis · Vehicles built Jan 2017 – Nov 2017
Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Mar 2016 Apr 2016 – Dec 2016 Jan 2017 – Nov 2017 from Dec 2017
DESCRIPTION
If any of the following operations are performed, the certification ECU (smart key ECU assembly) receives a signal, and changes the power source mode.- With the electrical key transmitter sub-assembly in the cabin, the engine switch is pressed.
- When the battery of the electrical key transmitter sub-assembly is depleted, the brake pedal is depressed and the electrical key transmitter sub-assembly is held near the engine switch.
- When the entry cancel function has been canceled through the customized parameters, the brake pedal is depressed and the electrical key transmitter sub-assembly is held near the engine switch.
- HINT:
- When the cable is disconnected and reconnected to the negative (-) battery terminal, the power source mode returns to the state it was in before the cable was disconnected.
- If the room oscillator does not recognize the key, the cause of the malfunction may be stored in the certification ECU (smart key ECU assembly).
- If the cause of the malfunction is stored in the certification ECU (smart key ECU assembly), the following table is helpful in checking whether or not the malfunction was caused by wave interference.
- When the cable is disconnected and reconnected to the negative (-) battery terminal, the power source mode returns to the state it was in before the cable was disconnected.
Radio Wave Interference: Problem Symptom
Data List Item
Operating Engine Switch / Key RF Signal Interference
- When the engine switch was operated, the electrical key transmitter sub-assembly could not be confirmed due to wave interference. Therefore, the output frequency was switched to the other channel (changed from channel 1 to channel 2 or from channel 2 to channel 1).
- If the cause of the malfunction has not been stored but any devices that can cause wave interference in the cabin have been removed and the room oscillator successfully recognizes the key, the possibility of wave interference is high.
- When the engine switch was operated, the electrical key transmitter sub-assembly could not be confirmed due to wave interference. Therefore, the output frequency was switched to the other channel (changed from channel 1 to channel 2 or from channel 2 to channel 1).
| Problem Symptom |
Data List Item |
Active Test Item |
| Power source mode does not change to on (IG) or on (ACC) |
Power Source Control
|
- |
WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- When using the GTS with the vehicle engine switch off, connect the GTS to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry & Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.
- The smart entry and start system (for Start Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (Click here). Troubleshoot the smart entry and start system (for Start Function) after confirming that the communication systems are functioning properly.
- Make sure that no DTCs are output. If any DTCs are output, proceed to the Diagnostic Trouble Code Chart (Click here).
- If the smart entry and start system is disabled through the customize function, enable the system before performing troubleshooting (Click here).
- Before replacing the certification ECU (smart key ECU assembly), electrical key transmitter sub-assembly or ID code box (immobiliser code ECU), refer to the smart entry and start system (for Start Function) precaution (Click here).
- Inspect the fuses of circuits related to this system before performing the following inspection procedure.
- After completing repairs, confirm that the problem does not occur.
- When using the GTS with the vehicle engine switch off, connect the GTS to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry & Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.
| 1. CHECK TRANSMITTER BATTERY |
Press a switch of the electrical key transmitter sub-assembly and check that the transmitter LED illuminates.
- OK:
- The electrical key transmitter sub-assembly LED illuminates.
|
|
||||
| OK | |
| 2. READ VALUE USING GTS (KEY LOW BATTERY) |
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Entry&Smart / Data List.
According to the display on the GTS, read the Data List.
Entry&Smart Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Key Low Battery
Transmitter battery depleted/Yes or No
Yes: Transmitter battery depleted
No: Transmitter battery not depleted
The electrical key transmitter sub-assembly sends voltage information to the certification ECU (smart key ECU assembly) when it is transmitting. The certification ECU (smart key ECU assembly) displays "Yes" for the "Key Low Battery" item of the Data List when this voltage information indicates 2.2 V or less.
This Data List item should be checked when the electrical key transmitter sub-assembly is at room temperature (example: at -20°C (-4°F), "Yes" may be displayed even if the transmitter battery is new).
- OK:
- "NO" is displayed in the Data List.
|
|
||||
| OK | |
| 3. CHECK POWER SOURCE MODE |
Get into the vehicle while carrying an electrical key transmitter sub-assembly.
Move the shift lever to P.
Press the engine switch with the brake pedal released and check that the power source mode changes.
- OK:
- The power source mode changes.
|
|
||||
| OK | ||
| ||
| 4. CHECK SMART ENTRY AND START SYSTEM |
Remove the transmitter battery from the electrical key transmitter sub-assembly (Click here).
With the brake pedal depressed, hold the electrical key transmitter sub-assembly near the engine switch and check if the power source mode changes.

- OK:
- The power source mode changes.
- HINT:
- If the power source mode changes, the cabin verification is malfunctioning.
- Result:
Result
Proceed to
The power source mode does not change.
A
The power source mode changes.
B
|
|
||||
| A | |
| 5. CHECK FOR DTC |
Using the GTS, check for certification ECU (smart key ECU assembly) DTCs (Click here).
- Result:
Result
Proceed to
DTCs are not output.
A
Smart entry and start system (for Start Function) DTCs are output
B
|
|
||||
| A | |
| 6. CHECK HARNESS AND CONNECTOR (POWER SOURCE) |
Disconnect the B75 certification ECU (smart key ECU assembly) connector.
Measure the voltage according to the value(s) in the table below.


Text in Illustration *a
Front view of wire harness connector
(to Certification ECU (Smart Key ECU Assembly))
-
-
- Standard Voltage:
Tester Connection
Condition
Specified Condition
B75-1 (+B) - Body ground
Always
11 to 14 V
|
|
||||
| OK | |
| 7. CHECK HARNESS AND CONNECTOR (GROUND) |
Disconnect the B75 certification ECU (smart key ECU assembly) connector.
Measure the resistance according to the value(s) in the table below.


Text in Illustration *a
Front view of wire harness connector
(to Certification ECU (Smart Key ECU Assembly))
-
-
- Standard Resistance:
Tester Connection
Condition
Specified Condition
B75-10 (E) - Body ground
Always
Below 1 Ω
|
|
||||
| OK | |
| 8. CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - IG1 RELAY) |
Disconnect the B75 certification ECU (smart key ECU assembly) connector.
Remove the IG1 relay from the instrument panel junction block assembly.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
B75-20 (IG1D) - 1 (IG1 relay)
Always
Below 1 Ω
2 (IG1 relay) - Body ground
B75-20 (IG1D) or 1 (IG1 relay) - Body ground
10 kΩ or higher
|
|
||||
| OK | |
| 9. INSPECT IG1 RELAY |
Remove the IG1 relay from the instrument panel junction block assembly.
Measure the resistance according to the value(s) in the table below.

- Standard Resistance:
Tester Connection
Condition
Specified Condition
3 - 5
Battery voltage not applied to terminals 1 and 2
10 kΩ or higher
Battery voltage applied to terminals 1 and 2
Below 1 Ω
|
|
||||
| OK | |
| 10. CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - NO. 2 INTEGRATION RELAY) |
Disconnect the B75 certification ECU (smart key ECU assembly) connector.
Disconnect the 12D and 12E No. 2 integration relay connectors.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
B75-20 (IG1D) - 12D-2
Always
Below 1 Ω
B75-21 (ACCD) - 12E-8
12E-4 - Body ground
B75-20 (IG1D) or 12D-2 - Body ground
10 kΩ or higher
B75-21 (ACCD) or 12E-8 - Body ground
|
|
||||
| OK | |
| 11. INSPECT NO. 2 INTEGRATION RELAY |
Remove the No. 2 integration relay.
Measure the resistance according to the value(s) in the table below.


Text in Illustration *a
Component without harness connected
(No. 2 Integration Relay)
-
-
- Standard Resistance:
Tester Connection
Condition
Specified Condition
12A-1 - 12D-8
Battery voltage not applied to terminals 12D-2 and 12E-4
10 kΩ or higher
Battery voltage applied to terminals 12D-2 and 12E-4
Below 1 Ω
12E-7 - 12E-9
Battery voltage not applied to terminals 12E-8 and 12E-4
10 kΩ or higher
Battery voltage applied to terminals 12E-8 and 12E-4
Below 1 Ω
|
|
||||
| OK | |
| 12. CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) |
Reconnect the B75 certification ECU (smart key ECU assembly) connector.
Install the IG1 relay.
Install the No. 2 integration relay.
Read the Data List according to the display on the GTS.


Text in Illustration *a
Component with harness connected
(Certification ECU (Smart Key ECU Assembly))
-
-
| Tester Display |
Measurement Item/Range |
Normal Condition |
Diagnostic Note |
| Power Supply Condition |
Power supply state/ST ON, All OFF, IG ON or ACC ON |
All OFF: Engine switch off (ACC and IG) ACC ON: Engine switch on (ACC) IG ON: Engine switch on (IG) ST ON: Sending engine start request signal |
- |
Measure the voltage while checking the Data List on the GTS.
- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
B75-20 (IG1D) - Body ground
Engine switch off
1 V or less
Engine switch on (ACC)
Engine switch on (IG)
9 V or higher
B75-21 (ACCD) - Body ground
Engine switch off
1 V or less
Engine switch on (IG)
8.5 V or higher
Engine switch on (ACC)
|
|
||||
| OK | ||
| ||
| 13. READ VALUE USING GTS (START SWITCH1, START SWITCH2) |
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Power Source Control / Data List.
Read the Data List according to the display on the GTS.
Power Source Control Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Start Switch1
Engine switch 1 status/ON or OFF
ON: Engine switch pressed
OFF: Engine switch not pressed
- If the engine switch is pressed for a short time, the display may not change.
- Use this item to determine whether the engine switch input signal is malfunctioning.
Start Switch2
Engine switch 2 status/ON or OFF
ON: Engine switch pressed
OFF: Engine switch not pressed
- Backup for engine switch 1. However, when the engine switch is pressed and held, the control functions only when both engine switch 1 and 2 are normal.
- Behaves the same way as engine switch 1.
- OK:
- ON (engine switch is pressed) and OFF (engine switch is not pressed) appear on the screen.
- If the engine switch is pressed for a short time, the display may not change.
|
|
||||
| OK | ||
| ||
| 14. INSPECT TRANSMITTER BATTERY |
Inspect the transmitter battery (Click here).
- NOTICE:
- Do not wrap the lead wire around a terminal, wedge it between terminals, or solder it. The terminal may be deformed or damaged, and the transmitter battery will not be able to be installed correctly.
|
|
||||
| OK | ||
| ||
| 15. INSPECT ENGINE SWITCH |
Remove the engine switch (Click here).
Inspect the engine switch (Click here).
|
|
||||
| OK | |
| 16. CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ENGINE SWITCH) |
Disconnect the B75 certification ECU (smart key ECU assembly) connector.
Disconnect the I32 engine switch connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
B75-18 (SSW1) - I32-5 (SS1)
Always
Below 1 Ω
B75-16 (SSW2) - I32-1 (SS2)
B75-24 (AGND) - I32-6 (AGND)
B75-18 (SSW1) or I32-5 (SS1) - Body ground
10 kΩ or higher
B75-16 (SSW2) or I32-1 (SS2) - Body ground
B75-24 (AGND) or I32-6 (AGND) - Body ground
|
|
||||
| OK | ||
| ||
