2014-2019 Hiace · Service Manual TRANSMISSION

P0741 Torque Converter Clutch Solenoid Performance (Shift Solenoid Valve SL)

Diagnostic trouble codes · Vehicles built Jan 2015 – Mar 2016

Versions by build date: Jan 2015 – Mar 2016 Apr 2016 – Dec 2016 Jan 2017 – Nov 2017 from Dec 2017

SYSTEM DESCRIPTION

The ECM uses signals from the throttle position sensor, air-flow meter, transmission revolution sensor (NT), transmission revolution sensor (SP2) and crankshaft position sensor to help determine the engagement timing of the lock-up clutch. The ECM monitors the engagement of the clutch using the transmission revolution sensor (NT), transmission revolution sensor (SP2) and crankshaft position sensor.
Then the ECM compares the engagement condition of the lock-up clutch with the lock-up schedule in the ECM memory to detect shift solenoid valve SL, transmission valve body assembly and torque converter assembly mechanical problems.
DTC No.
DTC Detection Condition
Trouble Area
P0741
Lock-up does not occur when requested (2 trip detection logic).
  1. Shift solenoid valve SL remains closed
  2. Transmission wire
  3. Transmission valve body assembly is blocked
  4. Torque converter assembly
  5. Automatic transmission assembly (clutch, brake or gear etc.)
  6. Line pressure is too low

MONITOR DESCRIPTION

Torque converter lock-up is controlled by the ECM based on the transmission revolution sensor (NT), transmission revolution sensor (SP2), engine speed, engine load, engine temperature, vehicle speed, transmission fluid temperature, and gear selection. The ECM determines the lock-up status of the torque converter by comparing the engine speed (NE) to the input turbine speed (NT). The ECM calculates the actual transmission gear by comparing the input turbine speed (NT) to the output shaft speed (SP2). When conditions are appropriate, the ECM requests "lock-up" by applying control voltage to shift solenoid valve SL. When shift solenoid valve SL is turned on, it applies pressure to the lock-up relay valve and locks the torque converter.
If the ECM detects no lock-up after lock-up has been requested or if it detects lock-up when it is not requested, the ECM interprets this as a fault in shift solenoid valve SL or lock-up system performance. The ECM will illuminate the MIL and store the DTC.

HINT:
Example:
When the following is met, the system judges it as a malfunction.

  1. There is a difference in rotation speed between the input side (engine speed) and output side (input turbine speed) of the torque converter when the ECM commands lock-up.
    (Engine speed is at least 70 rpm more than the input turbine speed.)
  2. There is no difference in rotation speed between the input side (engine speed) and output side (input turbine speed) of the torque converter when the ECM commands lock-up off.
    (The difference between engine speed and input turbine speed is less than 35 rpm.)

INSPECTION PROCEDURE

NOTICE:
Perform registration and/or initialization when parts related to the automatic transmission are replaced (Click here).


ACTIVE TEST

HINT:
Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

  1. Warm up the engine.

  2. Turn the ignition switch off.

  3. Connect the GTS to the DLC3.

  4. Turn the ignition switch to ON.

  5. Turn the GTS on.

  6. Enter the following menus: Powertrain / Engine and ECT / Active Test.

  7. According to the display on the GTS, perform the Active Test.

    Engine and ECT 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Activate the Lock Up
    Controls the shift solenoid valves SLU and SL to set the automatic transmission to the lock-up condition.
    ON/OFF
    Can be used to check shift solenoid valves SLU and SL operation.
    [Vehicle Condition]
    1. Throttle valve opening angle: Less than 30%
    2. Vehicle speed: 80 km/h (50 mph) or more

    HINT:
    1. This test can be conducted when the vehicle speed is 80 km/h (50 mph) or more.

  8. Lightly depress the accelerator pedal and check that the engine speed does not change abruptly.

    HINT:
    1. When changing the accelerator pedal opening angle while driving, if the engine speed does not change, lock-up is on.
    2. Slowly release the accelerator pedal in order to decelerate, but do not fully release the pedal. (Fully releasing the pedal will close the throttle valve and lock-up may be turned off.)

    C159073E06


1. CHECK OTHER DTCS OUTPUT (IN ADDITION TO DTC P0741)
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the GTS on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the DTCs using the GTS.

    Result 
    Result
    Proceed to
    Only DTC P0741 is output
    A
    P0741 and other DTCs are output
    B

    HINT:
    If any other codes besides P0741 are output, perform the troubleshooting for those DTCs first.



B
GO TO DTC CHART (Click here)
A


2. INSPECT TRANSMISSION WIRE (SHIFT SOLENOID VALVE SL)

  1. C319326E02
    Disconnect the transmission wire connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 (SL) - Body ground
    20°C (68°F)
    11 to 15 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Transmission Wire)



NG
Go to step 6
OK


3. INSPECT SHIFT SOLENOID VALVE SL (OPERATION)

  1. C320235E01
    Remove shift solenoid valve SL (Click here).

  1. Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.

    OK:
    Measurement Condition
    Specified Condition
    1. Battery positive (+) → Shift solenoid valve SL connector
    2. Battery negative (-) → Shift solenoid valve SL body
    Valve moves and makes an operating noise

    Text in Illustration 
    *1
    Shift Solenoid Valve SL



NG
REPLACE SHIFT SOLENOID VALVE SL (Click here)
OK


4. INSPECT TRANSMISSION VALVE BODY ASSEMBLY
  1. Check the transmission valve body assembly (Click here).

    OK:
    There is no foreign matter on each valve and they operate smoothly.



NG
REPAIR OR REPLACE TRANSMISSION VALVE BODY ASSEMBLY (Click here)
OK


5. INSPECT TORQUE CONVERTER ASSEMBLY
  1. Check the torque converter assembly (Click here).

    OK:
    The torque converter operates normally.



NG
REPLACE TORQUE CONVERTER ASSEMBLY (Click here)
OK

REPAIR OR REPLACE AUTOMATIC TRANSMISSION ASSEMBLY (Click here)

6. INSPECT SHIFT SOLENOID VALVE SL (RESISTANCE)

  1. C320236E01
    Remove shift solenoid valve SL (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Shift solenoid valve SL connector terminal - Shift solenoid valve SL body
    20°C (68°F)
    11 to 15 Ω

    Text in Illustration 
    *1
    Shift Solenoid Valve SL



NG
REPLACE SHIFT SOLENOID VALVE SL (Click here)
OK

REPLACE TRANSMISSION WIRE (Click here)


← P0722 Output Speed Sensor Circuit No Signal (+ P077C, P077D) (from Dec 2017)P0741 Torque Converter Clutch Solenoid Performance (Shift Solenoid Valve SL) (Apr 2016 – Dec 2016) →