2014-2019 Hiace · Service Manual SECURITIES

B2799 Engine Immobiliser System Malfunction

Diagnostic trouble codes · Vehicles built Oct 2014 – Dec 2014

Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Mar 2016 from Apr 2016

DESCRIPTION

When there are communication malfunctions between the ECM and ID code box (immobiliser code ECU), or when the communication ID codes do not match, the ECM stores this DTC.
DTC Code
DTC Detection Condition
Trouble Area
DTC Output Confirmation Operation
B2799
Either condition is met (1 trip detection logic*):
  1. A malfunction in the communication or communication lines between the ECM and ID code box (immobiliser code ECU).
  2. A matching communication code cannot be verified during communication between the ECM and ID code box (immobiliser code ECU).
  1. ID code box (immobiliser code ECU)
  2. ECM
  3. Harness or connector
Either condition is met:
  1. Within 10 seconds of an engine start operation being performed (with the shift lever in P and the brake pedal depressed, the engine switch is pressed while carrying the key). If there is a malfunction, the engine stops (communication begins within 3 seconds of the engine start operation being performed, and DTCs are stored after 6 seconds).
  2. 10 seconds after the engine switch is turned on (IG) after reconnecting the cable to the negative (-) battery terminal (communication begins within 3 seconds of the engine switch being turned on [IG], and DTCs are stored after 6 seconds).
  1. *: Only output while a malfunction is present.
Vehicle Condition and Fail-safe Operation when Malfunction Detected 
Vehicle Condition when Malfunction Detected
Fail-safe Operation when Malfunction Detected
Engine cannot be started
-
Related Data List and Active Test 
DTC Code
Data List and Active Test
B2799
-

WIRING DIAGRAM

B271006E37

INSPECTION PROCEDURE

NOTICE:
  1. When replacing the ID code box (immobiliser code ECU), refer to the Service Bulletin.
  2. After performing repairs, perform the DTC output confirmation operation, and then confirm that no DTCs are output again.

HINT:
When DTC B2799 and a certification ECU (smart key ECU assembly) DTC are output simultaneously, first perform troubleshooting for the certification ECU (smart key ECU assembly) DTC.


1. REGISTER ECU COMMUNICATION ID
  1. Register the ECU communication ID.

    HINT:
    Refer to the Service Bulletin.


NEXT


2. CLEAR DTC
  1. Clear the DTCs (Click here).


NEXT


3. CHECK FOR DTC
  1. Check for DTCs (Click here).

    HINT:
    Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.

    OK:
    DTC B2799 is not output.



NG
Go to step 4
OK

END (ECU COMMUNICATION ID HAS NOT BEEN REGISTERED)

4. REPLACE ECM
  1. Temporarily replace the ECM with a new or known good one (Click here).


NEXT


5. CLEAR DTC
  1. Clear the DTCs (Click here).


NEXT


6. CHECK FOR DTC
  1. Check for DTCs (Click here).

    HINT:
    Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.

    OK:
    DTC B2799 is not output.



NG
Go to step 7
OK

END (ECM WAS DEFECTIVE)

7. CHECK HARNESS AND CONNECTOR (ID CODE BOX [IMMOBILISER CODE ECU] - ECM)
  1. Disconnect the H81 ID code box (immobiliser code ECU) connector.

  1. Disconnect the B72 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    H81-3 (EFII) - B72-15 (IMO)
    Always
    Below 1 Ω
    H81-3 (EFII) - Body ground
    Always
    10 kΩ or higher
    B72-15 (IMO) - Body ground
    Always
    10 kΩ or higher
    H81-4 (EFIO) - B72-16 (IMI)
    Always
    Below 1 Ω
    H81-4 (EFIO) - Body ground
    Always
    10 kΩ or higher
    B72-16 (IMI) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ID CODE BOX (IMMOBILISER CODE ECU)


← B2790 ID BOX EEPROM Malfunction (from Oct 2014)B2799 Engine Immobiliser System Malfunction (Jan 2015 – Mar 2016) →