B1905/74 Short in Front Pretensioner Squib LH Circuit
Diagnostic trouble codes · Vehicles built from Jan 2017
Also covers:
- B1906/74 Open in Front Pretensioner Squib LH Circuit
- B1907/74 Short to GND in Front Pretensioner Squib LH Circuit
- B1908/74 Short to B+ in Front Pretensioner Squib LH Circuit
Versions by build date: Jan 2015 – Mar 2016 Apr 2016 – Dec 2016 from Jan 2017
DESCRIPTION
The front pretensioner LH circuit consists of the center airbag sensor assembly and front seat outer belt LH.This circuit instructs the SRS to deploy when deployment conditions are met.
These DTCs are stored when a malfunction is detected in the front pretensioner LH circuit.
| DTC Code |
DTC Detection Condition |
Trouble Area |
| B1905/74 |
One of the following conditions is met:
|
|
| B1906/74 |
One of the following conditions is met:
|
|
| B1907/74 |
One of the following conditions is met:
|
|
| B1908/74 |
One of the following conditions is met:
|
|
WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (Click here).
- After replacing the center airbag sensor assembly, refer to initialization (Click here).
- When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (Click here).
- HINT:
- To perform the simulation method, enter check mode (signal check) with the GTS (Click here), and then wiggle each connector of the airbag system or drive the vehicle on various types of road (Click here).
| 1. CHECK FRONT SEAT OUTER BELT LH |
Turn the ignition switch off.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Disconnect the connector from the front seat outer belt LH.
Connect the white wire side of SST (resistance: 2.1 Ω) to connector C.
- CAUTION:
- Never connect the tester to the front seat outer belt LH for measurement, as this may lead to a serious injury due to airbag deployment.
- NOTICE:
- Do not forcibly insert SST into the terminals of the connector when connecting SST.
- Insert SST straight into the terminals of the connector.
- Do not forcibly insert SST into the terminals of the connector when connecting SST.
- SST
- 09843-18061
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch ON, and wait for at least 60 seconds.
Clear the DTCs (Click here).
Turn the ignition switch off.
Turn the ignition switch ON, and wait for at least 60 seconds.
Check for DTCs (Click here).
- OK:
- DTC B1905, B1906, B1907 or B1908 is not output.
- HINT:
- Codes other than DTC B1905, B1906, B1907 and B1908 may be output at this time, but they are not related to this check.
Text in Illustration *1
Front Seat Outer Belt Assembly LH
*2
Center Airbag Sensor Assembly
*3
Connector C
*4
SST
*a
Front view of wire harness connector
(to Front Seat Outer Belt Assembly LH)
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Disconnect SST from connector C.
|
|
||||
| OK | ||
| ||
| 2. CHECK CONNECTORS |
Disconnect the connectors from the center airbag sensor assembly.
Turn the ignition switch to ON.
Check that the connectors (on the center airbag sensor assembly side and front seat outer belt LH side) are not damaged.

- OK:
- The lock button is not disengaged, and the claw of the lock is not deformed or damaged.
Text in Illustration *1
Front Seat Outer Belt Assembly LH
*2
Engine Room Main Wire
*3
Center Airbag Sensor Assembly
|
|
||||
| OK | |
| 3. CHECK ENGINE ROOM MAIN WIRE |
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
B23-1 (L+) - Body ground
Ignition switch ON
Below 1 V
B23-2 (L-) - Body ground
Ignition switch ON
Below 1 V
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
B23-1 (L+) - B23-2 (L-)
Always
Below 1 Ω
Release the activation prevention mechanism built into connector B (Click here).
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
B23-1 (L+) - B23-2 (L-)
Always
1 MΩ or higher
B23-1 (L+) - Body ground
Always
1 MΩ or higher
B23-2 (L-) - Body ground
Always
1 MΩ or higher
| *1 |
Front Seat Outer Belt Assembly LH |
| *2 |
Engine Room Main Wire |
| *3 |
Center Airbag Sensor Assembly |
| *4 |
Connector C |
| *a |
Front view of wire harness connector (to Front Seat Outer Belt Assembly LH) |
|
|
||||
| OK | |
| 4. CHECK DTC |
Connect the connectors to the front seat outer belt LH and center airbag sensor assembly.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch ON, and wait for at least 60 seconds.
Clear the DTCs (Click here).
Turn the ignition switch off.
Turn the ignition switch ON, and wait for at least 60 seconds.
Check for DTCs (Click here).
- OK:
- DTC B1905, B1906, B1907 or B1908 is not output.
- HINT:
- Codes other than DTC B1905, B1906, B1907 and B1908 may be output at this time, but they are not related to this check.
Text in Illustration *1
Front Seat Outer Belt Assembly LH
*2
Center Airbag Sensor Assembly
|
|
||||
| OK | ||
| ||
