2014-2019 Hiace · Service Manual COMMUNICATION SYSTEM

B2785 Communication Malfunction between ECUs Connected by LIN

Diagnostic trouble codes · Vehicles built Oct 2014 – Dec 2014

Versions by build date: Oct 2014 – Dec 2014 from Jan 2015

DESCRIPTION

The certification ECU (smart key ECU assembly) monitors the LIN communication bus between the components related to the certification intermittently. DTC B2785 is output when a malfunction in the LIN communication bus between the components related to the certification is detected continuously 3 times.
DTC Code
DTC Detection Condition
Trouble Area
B2785
Certification ECU (smart key ECU assembly) detects malfunction in LIN communication bus between components related to certification continuously 3 times
  1. Certification ECU (smart key ECU assembly)
  2. ID code box (immobiliser code ECU)
  3. Steering lock actuator assembly
  4. Harness or connector

WIRING DIAGRAM

B301186E04

INSPECTION PROCEDURE

NOTICE:
  1. When using the GTS with the engine switch off to troubleshoot:
    Connect the GTS to the vehicle, and turn a courtesy switch on and off at 1.5 second intervals until communication between the GTS and vehicle begins.
  2. Before replacing the certification ECU (smart key ECU assembly), refer to the smart entry and start system (for Entry Function) (Click here).


1. CLEAR DTC
  1. Clear the DTCs (Click here).


NEXT


2. CHECK FOR DTC
  1. Check for DTCs (Click here).

    Result 
    Result
    Proceed to
    DTC B2785 is output
    A
    DTC B2785 is not output
    B



B
USE SIMULATION METHOD TO CHECK (Click here)
A


3. CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] - ID CODE BOX [IMMOBILISER CODE ECU] OR STEERING LOCK ACTUATOR ASSEMBLY)
  1. Disconnect the B75 certification ECU (smart key ECU assembly) connector.

  1. Disconnect the H81 ID code box (immobiliser code ECU) connector.

  1. Disconnect the H80 steering lock actuator assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    B75-5 (LIN) - H80-5 (LIN)
    Always
    Below 1 Ω
    B75-5 (LIN) - H81-2 (LIN1)
    Always
    Below 1 Ω
    B75-5 (LIN) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. CLEAR DTC
  1. Disconnect the H80 steering lock actuator assembly connector.

  1. Clear the DTCs (Click here).


NEXT


5. CHECK FOR DTC
  1. Check for DTCs (Click here).

    Result 
    Result
    Proceed to
    DTC B2785 is output
    A
    DTC B2785 is not output
    B



B
REPLACE STEERING LOCK ACTUATOR ASSEMBLY (Click here)
A


6. CLEAR DTC
  1. Disconnect the H81 ID code box (immobiliser code ECU) connector.

  1. Clear the DTCs (Click here).


NEXT


7. CHECK FOR DTC
  1. Check for DTCs (Click here).

    Result 
    Result
    Proceed to
    DTC B2785 is output
    A
    DTC B2785 is not output
    B



B
REPLACE ID CODE BOX (IMMOBILISER CODE ECU)
A

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)


← DIAGNOSTIC TROUBLE CODE CHART (from Jan 2015)B2785 Communication Malfunction between ECUs Connected by LIN (from Jan 2015) →