2014-2019 Hiace · Service Manual COMMUNICATION SYSTEM

B2786 No Response from Steering Lock ECU

Diagnostic trouble codes · Vehicles built Oct 2014 – Dec 2014

Versions by build date: Oct 2014 – Dec 2014 from Jan 2015

DESCRIPTION

This DTC is output when LIN communication between the certification ECU (smart key ECU assembly) and steering lock actuator assembly stops for 10 seconds or more.
DTC Code
DTC Detection Condition
Trouble Area
B2786
Periodic transmission from steering lock actuator assembly stops for 10 seconds or more
  1. Certification ECU (smart key ECU assembly)
  2. Steering lock actuator assembly
  3. Harness or connector

WIRING DIAGRAM

B301188E05

INSPECTION PROCEDURE

NOTICE:
  1. When using the GTS with the engine switch off to troubleshoot:
    Connect the GTS to the vehicle, and turn a courtesy switch on and off at 1.5 second intervals until communication between the GTS and vehicle begins.
  2. Inspect the fuses for circuits related to this system before performing the following inspection procedure.
  3. Before replacing the certification ECU (smart key ECU assembly), refer to the smart entry and start system (for Entry Function) (Click here).

HINT:
DTC B2785 is output when the communication between all of the following components and certification ECU (smart key ECU assembly) stops.


1. CLEAR DTC
  1. Clear the DTCs (Click here).


NEXT


2. CHECK FOR DTC
  1. Check for DTCs (Click here).

    OK:
    DTC B2786 is not output.



NG
Go to step 3
OK

USE SIMULATION METHOD TO CHECK (Click here)

3. CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] - STEERING LOCK ACTUATOR ASSEMBLY)
  1. Disconnect the B75 certification ECU (smart key ECU assembly) connector.

  1. Disconnect the H80 steering lock actuator assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    B75-5 (LIN) - H80-5 (LIN)
    Always
    Below 1 Ω
    B75-5 (LIN) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. CHECK HARNESS AND CONNECTOR (STEERING LOCK ACTUATOR ASSEMBLY - BATTERY AND BODY GROUND)
B291261E04
  1. Disconnect the steering lock actuator assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    H80-1 (GND) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    H80-7 (B) - Body ground
    Always
    11 to 14 V
    H80-6 (IG2) - Body ground
    Engine switch on (IG)
    11 to 14 V

Text in Illustration 
*a
Front view of wire harness connector
(to Steering Lock Actuator Assembly)


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. REPLACE STEERING LOCK ACTUATOR ASSEMBLY
  1. Temporarily replace the steering lock actuator assembly with a new one (Click here).


NEXT


6. CLEAR DTC
  1. Clear the DTCs (Click here).


NEXT


7. CHECK FOR DTC
  1. Check for DTCs (Click here).

    OK:
    DTC B2786 is not output.



NG
REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
OK

END (STEERING LOCK ACTUATOR ASSEMBLY IS DEFECTIVE)


← B2785 Communication Malfunction between ECUs Connected by LIN (from Jan 2015)B2786 No Response from Steering Lock ECU (from Jan 2015) →