2014-2019 Hiace · Service Manual SUSPENSION & AXLE

C2126/26 Transmitter ID not Received in Main Mode

Diagnostic trouble codes · Vehicles built Jan 2017 – Nov 2017

Versions by build date: Jan 2017 – Nov 2017 from Dec 2017

DESCRIPTION

After all IDs are registered, DTC C2126/26 is stored in the tire pressure warning ECU and receiver and the tire pressure warning light blinks for 1 minute and then illuminates.
When the tire pressure warning ECU and receiver successfully receives radio waves from all the transmitters whose IDs are stored in the ECU, DTC C2126/26 is cleared and the tire pressure warning light goes off.
DTC No.
DTC Detection Condition
Trouble Area
C2126/26
After ID registration is completed, ECU does not receive radio waves from transmitters whose IDs are stored in ECU.
  1. Transmitter ID registration failure
  2. Tire pressure warning valve and transmitter
  3. Tire pressure warning ECU and receiver

NOTICE:
(Main) is displayed on the DTC screen for the DTCs even when the 2nd set of tires is selected.

HINT:
The purpose of this DTC is to help prevent delivering a vehicle that has incorrectly registered IDs. After all IDs are registered, DTC C2126/26 is detected and the tire pressure warning light blinks for 1 minute and then illuminates. If the tire pressure warning light does not turn off after a little while, IDs may be incorrectly registered.


WIRING DIAGRAM

C370426E01

INSPECTION PROCEDURE

NOTICE:
  1. When replacing the tire pressure warning ECU and receiver, read the transmitter IDs stored in the old ECU using the GTS and write them down before removal.
  2. It is necessary to perform initialization (Click here) after registration (Click here) of the transmitter IDs into the tire pressure warning ECU and receiver if the ECU and/or one of the valve and transmitters has been replaced.


1. IDENTIFY TRANSMITTER NOT RECEIVED
  1. Set the tire pressure to the specified values (Click here).

  1. Turn the ignition switch off.

  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the GTS on.

  1. Enter the following menus: Chassis / Tire Pressure Monitor / Data List.

  1. Display the "ID Tire Inflation Pressure" value for each wheel using the GTS.

  1. Rapidly reduce the tire pressure for each wheel at least 40 kPa (0.4 kg/cm2, 5.8 psi) within 30 seconds. If the "ID Tire Inflation Pressure" value displayed on the GTS does not change, the tire pressure warning valve and transmitter corresponding to the unchanged "ID Tire Inflation Pressure" value was the cause of the output DTC.

    HINT:
    1. Identify the malfunctioning tire pressure warning valve and transmitter by repeatedly decreasing the tire pressure for each tire.
    2. Record which "ID Tire Inflation Pressure" value corresponds to each tire.

    Tire Pressure Monitor 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    ID 1 Tire Inflation Pressure
    ID1 tire inflation pressure/
    min.: Absolute pressure (abs)/ 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (gauge)/ 0 kPa (0 kgf/cm2, 0 psi)
    max.: Absolute pressure (abs)/ 900 kPa (9.2 kgf/cm2, 131 psi), Relative pressure (gauge)/ 800 kPa (8.2 kgf/cm2, 116 psi)
    Actual tire inflation pressure
    If N/A is displayed, data has not been received.*
    ID 2 Tire Inflation Pressure
    ID2 tire inflation pressure/
    min.: Absolute pressure (abs)/ 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (gauge)/ 0 kPa (0 kgf/cm2, 0 psi)
    max.: Absolute pressure (abs)/ 900 kPa (9.2 kgf/cm2, 131 psi), Relative pressure (gauge)/ 800 kPa (8.2 kgf/cm2, 116 psi)
    Actual tire inflation pressure
    If N/A is displayed, data has not been received.*
    ID 3 Tire Inflation Pressure
    ID3 tire inflation pressure/
    min.: Absolute pressure (abs)/ 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (gauge)/ 0 kPa (0 kgf/cm2, 0 psi)
    max.: Absolute pressure (abs)/ 900 kPa (9.2 kgf/cm2, 131 psi), Relative pressure (gauge)/ 800 kPa (8.2 kgf/cm2, 116 psi)
    Actual tire inflation pressure
    If N/A is displayed, data has not been received.*
    ID 4 Tire Inflation Pressure
    ID4 tire inflation pressure/
    min.: Absolute pressure (abs)/ 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (gauge)/ 0 kPa (0 kgf/cm2, 0 psi)
    max.: Absolute pressure (abs)/ 900 kPa (9.2 kgf/cm2, 131 psi), Relative pressure (gauge)/ 800 kPa (8.2 kgf/cm2, 116 psi)
    Actual tire inflation pressure
    If N/A is displayed, data has not been received.*
    ID 5 Tire Inflation Pressure
    ID5 tire inflation pressure/
    min.: Absolute pressure (abs)/ 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (gauge)/ 0 kPa (0 kgf/cm2, 0 psi)
    max.: Absolute pressure (abs)/ 900 kPa (9.2 kgf/cm2, 131 psi), Relative pressure (gauge)/ 800 kPa (8.2 kgf/cm2, 116 psi)
    Actual tire inflation pressure
    If N/A is displayed, data has not been received.*

    HINT:
    1. *: It may take a few minutes until the values are displayed.
    2. The wheel position cannot be determined from ID1 through ID5 on the Data List.

  1. Check the Data List.

    NOTICE:
    1. It may take a few minutes to display the updated tire pressure data.
    2. When the "ID Tire Inflation Pressure" data has not changed, reset the tire pressure to the appropriate specified value and rotate the tire 90 to 270 degrees. Then rapidly release the tire pressure and recheck the data.
    3. Record the transmitter ID of which "ID Tire Inflation Pressure" data corresponds to each tire.

  1. After confirming that the "ID Tire Inflation Pressure" data for one tire has changed, repeat this procedure for each tire. Identify the transmitter not received.

    Result:
    Condition
    Proceed to
    One or more transmitters are abnormal
    A
    All transmitters are normal
    B



B
Go to step 5
A


2. CHECK TRANSMITTER ID
  1. Turn the ignition switch off.

  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the GTS on.

  1. Enter the following menus: Chassis / Tire Pressure Monitor / Data List.

  1. Check the values by referring to the table below.

    Tire Pressure Monitor 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Registered ID 1 code
    Registered ID1 code/
    min.: 0, max.: FFFFFFF*
    ID No. registered for transmitter ID1 displayed
    -
    Registered ID 2 code
    Registered ID2 code/
    min.: 0, max.: FFFFFFF*
    ID No. registered for transmitter ID2 displayed
    -
    Registered ID 3 code
    Registered ID3 code/
    min.: 0, max.: FFFFFFF*
    ID No. registered for transmitter ID3 displayed
    -
    Registered ID 4 code
    Registered ID4 code/
    min.: 0, max.: FFFFFFF*
    ID No. registered for transmitter ID4 displayed
    -
    Registered ID 5 code
    Registered ID5 code/
    min.: 0, max.: FFFFFFF*
    ID No. registered for transmitter ID5 displayed
    -

    HINT:
    1. *: Displayed only when the ID No. is not registered.
    2. The wheel position cannot be determined from ID1 through ID5 on the Data List.

  1. Check the ID number on the identified transmitter by removing it from the tire and wheel.C370424E01

    Text in Illustration 
    *1
    Tire Pressure Warning Valve and Transmitter
    *2
    Transmitter ID (7-digit number)
    *3
    White Resin Cover
    *4
    Identification Mark
    *a
    Surface A
    *b
    Surface B

    NOTICE:
    Make sure to use a tire pressure warning valve and transmitter that has a white cover. Otherwise, ID registration cannot be performed.

  1. Confirm that the ID number on the transmitter and the recorded transmitter ID match.

    Result:
    Result
    Proceed to
    Match
    A
    Do not match
    B



B
Go to step 4
A


3. REPLACE TIRE PRESSURE WARNING VALVE AND TRANSMITTER
  1. Replace the tire pressure warning valve and transmitter (Click here).


NEXT


4. REGISTRATION OF TRANSMITTER ID
  1. Perform registration (Click here).


NEXT


5. PERFORM INITIALIZATION
  1. Set the tire pressure to the specified value (Click here).

  1. Perform initialization (Click here).


NEXT


6. CONFIRM TIRE INFLATION PRESSURE (DATA LIST)
  1. Turn the ignition switch off.

  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the GTS on.

  1. Enter the following menus: Chassis / Tire Pressure Monitor / Data List.

  1. Check the values by referring to the table below.

    Tire Pressure Monitor 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    ID 1 Tire Inflation Pressure
    ID1 tire inflation pressure/
    min.: Absolute pressure (abs)/ 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (gauge)/ 0 kPa (0 kgf/cm2, 0 psi)
    max.: Absolute pressure (abs)/ 900 kPa (9.2 kgf/cm2, 131 psi), Relative pressure (gauge)/ 800 kPa (8.2 kgf/cm2, 116 psi)
    Actual tire inflation pressure
    If N/A is displayed, data has not been received.*
    ID 2 Tire Inflation Pressure
    ID2 tire inflation pressure/
    min.: Absolute pressure (abs)/ 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (gauge)/ 0 kPa (0 kgf/cm2, 0 psi)
    max.: Absolute pressure (abs)/ 900 kPa (9.2 kgf/cm2, 131 psi), Relative pressure (gauge)/ 800 kPa (8.2 kgf/cm2, 116 psi)
    Actual tire inflation pressure
    If N/A is displayed, data has not been received.*
    ID 3 Tire Inflation Pressure
    ID3 tire inflation pressure/
    min.: Absolute pressure (abs)/ 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (gauge)/ 0 kPa (0 kgf/cm2, 0 psi)
    max.: Absolute pressure (abs)/ 900 kPa (9.2 kgf/cm2, 131 psi), Relative pressure (gauge)/ 800 kPa (8.2 kgf/cm2, 116 psi)
    Actual tire inflation pressure
    If N/A is displayed, data has not been received.*
    ID 4 Tire Inflation Pressure
    ID4 tire inflation pressure/
    min.: Absolute pressure (abs)/ 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (gauge)/ 0 kPa (0 kgf/cm2, 0 psi)
    max.: Absolute pressure (abs)/ 900 kPa (9.2 kgf/cm2, 131 psi), Relative pressure (gauge)/ 800 kPa (8.2 kgf/cm2, 116 psi)
    Actual tire inflation pressure
    If N/A is displayed, data has not been received.*
    ID 5 Tire Inflation Pressure
    ID5 tire inflation pressure/
    min.: Absolute pressure (abs)/ 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (gauge)/ 0 kPa (0 kgf/cm2, 0 psi)
    max.: Absolute pressure (abs)/ 900 kPa (9.2 kgf/cm2, 131 psi), Relative pressure (gauge)/ 800 kPa (8.2 kgf/cm2, 116 psi)
    Actual tire inflation pressure
    If N/A is displayed, data has not been received.*

    HINT:
    1. *: It may take a few minutes until the values are displayed.
    2. When no "ID Tire Inflation Pressure" data has changed, reset the tire pressure to the appropriate specified value and rotate the tire 90 to 270 degrees. Then rapidly release the tire pressure and recheck the data.
    3. The wheel position cannot be determined from ID1 through ID5 on the Data List.

      Result:
      Result
      Proceed to
      Tire pressure values are not displayed.
      A
      All tire pressure readings are equal to specified values.
      B



B
END
A

REPLACE TIRE PRESSURE WARNING ECU AND RECEIVER (Click here)


← C2121/21 No Signal from Transmitter ID1 (+ 9 more codes) (from Dec 2017)C2126/26 Transmitter ID not Received in Main Mode (from Dec 2017) →