2014-2019 Hiace · Service Manual BRAKE

C1417 High Power Supply Voltage Malfunction

Diagnostic trouble codes · Vehicles built Jan 2017 – Nov 2017

Versions by build date: Jan 2015 – Mar 2016 Apr 2016 – Dec 2016 Jan 2017 – Nov 2017 from Dec 2017

DESCRIPTION

If a malfunction is detected in the power supply circuit, the skid control ECU (brake actuator assembly) stores this DTC and the fail-safe function prohibits ABS operation.
This DTC is stored when the IG1 terminal voltage deviates from the DTC detection condition due to a malfunction in the power supply or charging circuit such as the battery or alternator circuit, etc.
The DTC is canceled when the +BS terminal voltage returns to normal.
DTC No.
DTC Detection Condition
Trouble Area
C1417
Either of the following is detected:
  1. The +BS terminal voltage is 17.4 V or more for 0.8 seconds or more.
  2. When voltage at terminal +BS is 17.4 V or higher, power supply voltage of master cylinder pressure sensor is cut for 0.2 seconds or more.
  1. Charging system
  2. Skid control ECU (Brake actuator assembly)
  3. Wire harness or connector
  4. ABS SOL fuse
  5. Battery

WIRING DIAGRAM

C307645E01

INSPECTION PROCEDURE

NOTICE:
  1. When replacing the skid control ECU (brake actuator assembly), perform zero point calibration and store system information (Click here).
  2. Inspect the fuses for circuits related to this system before performing the following inspection procedure.


1. INSPECT BATTERY
  1. Check the battery voltage.

    Standard voltage:
    11 to 14 V


    HINT:
    Refer to the inspection procedures: 
    Item
    See page
    1KD-FTV
    Click here
    2KD-FTV
    Click here
    1TR-FE
    Click here
    2TR-FE (except Dual VVT-i)
    Click here
    2TR-FE (w/ Dual VVT-i)
    Click here



NG
CHECK OR REPLACE CHARGING SYSTEM COMPONENT OR BATTERY
OK


2. CHECK HARNESS AND CONNECTOR (+BS TERMINAL)
C306843E01
  1. Turn the ignition switch off.

  1. Make sure that there is no looseness at the locking part and the connecting part of the connector.

  1. Disconnect the B92 skid control ECU (brake actuator assembly) connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    B92-38 (+BS) - Body ground
    Always
    11 to 14 V
    B92-38 (+BS) - B92-25 (GND1)
    Always
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Skid Control ECU (Brake Actuator Assembly))



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (+BS CIRCUIT)
OK


3. RECONFIRM DTC
  1. Reconnect the B92 skid control ECU (brake actuator assembly) connector.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Start the engine.

  1. Perform a road test.

  1. Check if the same DTC is recorded (Click here).

    Result:
    Result
    Proceed to
    DTC C1417 is not output
    A
    DTC C1417 is output
    B

    HINT:
    If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step (Click here).



B
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)
A

USE SIMULATION METHOD TO CHECK (Click here)


← C1417 High Power Supply Voltage Malfunction (Apr 2016 – Dec 2016)C1417 High Power Supply Voltage Malfunction (from Dec 2017) →