B1612/83 Lost Communication with Front Airbag Sensor RH
Diagnostic trouble codes · Vehicles built Jan 2015 – Mar 2016
Also covers:
- B1613/83 Front Airbag Sensor RH Initialization Incomplete
Versions by build date: Jan 2015 – Mar 2016 Apr 2016 – Dec 2016 from Jan 2017
DESCRIPTION
The front airbag sensor RH circuit consists of the center airbag sensor assembly and front airbag sensor RH.The front airbag sensor RH detects impacts to the vehicle and sends signals to the center airbag sensor assembly to determine if the airbag should be deployed.
DTC B1612/83 or B1613/83 is stored when a malfunction is detected in the front airbag sensor RH circuit.
| DTC Code |
DTC Detection Condition |
Trouble Area |
| B1612/83 |
One of the following conditions is met:
|
|
| B1613/83 |
One of the following conditions is met:
|
|
WIRING DIAGRAM




INSPECTION PROCEDURE
- NOTICE:
- When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (Click here).
- After replacing the center airbag sensor assembly, refer to initialization (Click here).
- When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (Click here).
| 1. CHECK CONNECTION OF CONNECTORS |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Check that the connectors are properly connected to the center airbag sensor assembly and front airbag sensor RH.
- OK:
- The connectors are properly connected.
|
|
||||
| OK | |
| 2. CHECK CONNECTORS |
Disconnect the connectors from the center airbag sensor assembly and front airbag sensor RH.
Check that the connectors (on the center airbag sensor assembly side and front airbag sensor RH side) are not damaged.

- OK:
- The connectors are not deformed or damaged.
Text in Illustration *1
Front Airbag Sensor RH
*2
Center Airbag Sensor Assembly
*3
Wiring Cowl to Headlight Harness Assembly
*4
Engine Room Main Wire
|
|
||||
| OK | |
| 3. CHECK FRONT AIRBAG SENSOR RH CIRCUIT |
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


Text in Illustration *1
Front Airbag Sensor RH
*2
Center Airbag Sensor Assembly
*3
Connector E
*4
Connector B
*5
Service Wire
*6
Wiring Cowl to Headlight Harness Assembly
*7
Engine Room Main Wire
-
-
*a
Front view of wire harness connector
(to Front Airbag Sensor RH)
*b
Rear view of wire harness connector
(to Center Airbag Sensor Assembly)
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
A12-2 (+SR) - Body ground
Ignition switch ON
Below 1 V
A12-1 (-SR) - Body ground
Ignition switch ON
Below 1 V
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Using a service wire, connect terminals 29 (+SR) and 27 (-SR) of connector B.
- NOTICE:
- Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
A12-2 (+SR) - A12-1 (-SR)
Always
Below 1 Ω
Disconnect the service wire from connector B.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
A12-2 (+SR) - A12-1 (-SR)
Always
1 MΩ or higher
A12-2 (+SR) - Body ground
Always
1 MΩ or higher
A12-1 (-SR) - Body ground
Always
1 MΩ or higher
|
|
||||
| OK | |
| 4. CHECK FRONT AIRBAG SENSOR RH |
Connect the connectors to the center airbag sensor assembly .

Interchange the front airbag sensor RH with LH and connect the connectors to them.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in memory (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (Click here).
Result Result
Proceed to
DTC B1612, B1613, B1617 and B1618 are not output
A
DTC B1617 or B1618 is output
B
DTC B1612 or B1613 is output
C
- HINT:
- Codes other than DTC B1612, B1613, B1617 and B1618 may be output at this time, but they are not related to this check.
Text in Illustration *1
Front Airbag Sensor LH
*2
Center Airbag Sensor Assembly
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Return the front airbag sensor LH and RH to their original positions and connect the connectors to them.
|
|
||||
|
|
||||
| C | ||
| ||
| 5. CHECK ENGINE ROOM MAIN WIRE |
Disconnect the wiring cowl to headlight harness assembly connector from the engine room main wire.


Text in Illustration *A
for LHD
*B
for RHD
*1
Front Airbag Sensor RH
*2
Center Airbag Sensor Assembly
*3
Wiring Cowl to Headlight Harness Assembly
*4
Engine Room Main Wire
*5
Connector C
*6
Connector B
*7
Service Wire
-
-
*a
Front view of wire harness connector
(to Engine Room Main Wire)
*b
Rear view of wire harness connector
(to Center Airbag Sensor Assembly)
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
- for LHD:
Tester Connection
Switch Condition
Specified Condition
AB2-1 (+SR) - AB3-1 (+SR)
Ignition switch ON
Below 1 V
AB2-3 (-SR) -AB3-3 (-SR)
Ignition switch ON
Below 1 V
- for RHD:
Tester Connection
Switch Condition
Specified Condition
AB3-1 (+SR) - Body ground
Ignition switch ON
Below 1 V
AB3-3 (-SR) - Body ground
Ignition switch ON
Below 1 V
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Using a service wire, connect terminals 29 (+SR) and 27 (-SR) of connector B.
- NOTICE:
- Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
- for LHD:
Tester Connection
Condition
Specified Condition
AB2-1 (+SR) - AB2-3 (-SR)
Always
Below 1 Ω
- for RHD:
Tester Connection
Condition
Specified Condition
AB3-1 (+SR) - AB3-3 (-SR)
Always
Below 1 Ω
Disconnect the service wire from connector B.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
- for LHD:
Tester Connection
Condition
Specified Condition
AB2-1 (+SR) - AB2-3 (-SR)
Always
1 MΩ or higher
AB2-1 (+SR) - Body ground
Always
1 MΩ or higher
AB2-3 (-SR) - Body ground
Always
1 MΩ or higher
- for RHD:
Tester Connection
Condition
Specified Condition
AB3-1 (+SR) - AB3-3 (-SR)
Always
1 MΩ or higher
AB3-1 (+SR) - Body ground
Always
1 MΩ or higher
AB3-3 (-SR) - Body ground
Always
1 MΩ or higher
|
|
||||
| OK | ||
| ||
