2014-2019 Hiace · Service Manual ENGINE

Brake Override System

Circuit diagnosis · Vehicles built from Jan 2017

DESCRIPTION

When the vehicle is being driven, depressing the accelerator pedal sensor assembly and brake pedal will activate the brake override system to restrict driving torque. The conditions for activating the brake override system as well as the items that are controlled are explained below.
A358347E01
  1. Activation Conditions:
    When the accelerator pedal and brake pedal are depressed.

    NOTICE:
    The vehicle may not enter the brake override system control due to the relation of the accelerator pedal angle and the vehicle's speed.

  1. Items Controlled:
    1. When the vehicle speed is extremely low, the accelerator opening value used when controlling the engine is reduced more than normal.

      HINT:
      During control, the Accelerator Position value in the Data List will be lower than normal.

    2. When the vehicle speed is not extremely low, the accelerator opening value is forcibly lowered to a fixed value.

      HINT:
      1. During control, the Accelerator Position value in the Data List is forcibly reduced to a specified value regardless of the actual accelerator opening value (Accel Sens. No. 1 Volt %).
      2. During brake override system control, the operation indicator is displayed on the meter.

  1. Deactivation Conditions:
    1. When the Stop Light Switch turns OFF or the actual accelerator pedal returns to some degree.

INSPECTION PROCEDURE

  1. Inspection Method
    Example:
    Drive at 10 km/h (6.25 mph), depress the accelerator pedal by 1/2 to 3/4 and keep it in that position. Under these conditions, if the engine speed decreases to 1000 rpm when the brake pedal is depressed, then the brake override system has been activated.

CAUTION:
When carrying out the inspection, use a place where you are able to carry it out safely and also pay close attention to your surroundings.
Also, when driving make absolutely sure that all road traffic laws, such as speed limits, are observed.

HINT:
  1. Under normal conditions, the Accelerator Position value changes in response to the Accel Sens. No.1 Volt % value. For more information on the numerical values, refer to the Data List (Click here).
  2. If the Data List values of Accelerator Position and Accel Sens. No.1 Volt % do not match, and the value of Accelerator Position changes but the value of Accel Sens. No.1 Volt % is constant, this confirms that the brake override system has activated. (Data can be captured relatively easily by using the snapshot function in the Data List. Confirm the data after performing the driving test.)

NOTICE:
The brake override system restricts driving torque if the brake pedal is depressed when driving with the accelerator pedal depressed. If a customer reports experiencing loss of torque after the accelerator and brake pedals have both been intentionally depressed, explain to the customer that this is not a malfunction, and that the customer should avoid depressing both the accelerator and brake pedals at the same time.
Example: While operating the accelerator pedal, the customer uses their left foot to operate the brake pedal.


1. CHECK DTC OUTPUT
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON and turn the GTS on.

  1. Enter the following menus: System Select / Health Check.

  1. Check DTCs.

    Result 
    Result
    Proceed to
    No DTC output
    A
    DTC output
    B



B
GO TO DTC CHART
A


2. READ VALUE USING GTS (STOP LIGHT SWITCH AND ST1)
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON and turn the GTS on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Stop Light Switch and ST1.

  1. Check the Data List indication when the brake pedal is depressed and released.

    OK:
    GTS Display
    Condition
    Specified Condition
    Stop Light Switch
    Brake pedal released
    OFF
    Brake pedal depressed
    ON
    ST1
    Brake pedal released
    OFF
    Brake pedal depressed
    ON



NG
INSPECT STOP LIGHT SWITCH ASSEMBLY (Click here)
OK


3. INSPECT BRAKE PEDAL
  1. Inspect and adjust the brake pedal (Click here).

    HINT:
    If the stop light switch turns ON too late, the start of brake override system control may be delayed; if it turns ON too soon, brake override system control may begin too early, so conduct inspection of the brake pedal and stop light switch assembly.



NG
REPAIR OR REPLACE BRAKE PEDAL (Click here)
OK


4. READ VALUE USING GTS (ACCELERATOR PEDAL POSITION SENSOR)
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON and turn the GTS on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Accel Sens. No.1 Volt % and Accel Sens. No.2 Volt %.

  1. Read the value displayed on the GTS.

    OK:
    GTS Display
    Condition
    Specified Condition
    Accel Sens. No.1 Volt %
    Accelerator Pedal
    Released → Depressed → Released
    Values smoothly change following accelerator pedal operation
    Accel Sens. No.2 Volt %

    HINT:
    For numerical values of Accel Sens. No.1 Volt % and Accel Sens. No.2 Volt %, refer to the Data List (Click here).



NG
REPLACE ACCELERATOR PEDAL SENSOR ASSEMBLY (Click here)
OK


5. READ VALUE USING GTS (VEHICLE SPEED)
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON and turn the GTS on.

  1. Start the engine.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / Vehicle Speed.

  1. Read the value displayed on the GTS.

    Standard:
    GTS Display
    Condition
    Specified Condition
    Vehicle Speed
    Vehicle stopped, engine running
    0 km/h (0 mph)
    Vehicle running at constant speed between 16.1 to 64.4 km/h (10 to 40 mph)
    No large fluctuations when driving at a constant speed

    CAUTION:
    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

    HINT:
    Data can be captured relatively easily by using the snapshot function in the Data List. Confirm the data after performing the drive test.



NG
GO TO VEHICLE SPEED SENSOR SIGNAL CIRCUIT MALFUNCTION (Click here)
OK


6. READ VALUE USING GTS (FR, FL, RR, RL WHEEL SPEED)
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON and turn the GTS on.

  1. Start the engine.

  1. Enter the following menus: Chassis / ABS/VSC/TRC / Data List / FR Wheel Speed, FL Wheel Speed, RR Wheel Speed and RL Wheel Speed.

  1. Read the value displayed on the GTS.

    Standard:
    GTS Display
    Condition
    Specified Condition
    FR Wheel Speed
    FL Wheel Speed
    RR Wheel Speed
    RL Wheel Speed
    Vehicle stopped, engine running
    0 km/h (0 mph)
    Vehicle running at constant speed between 16.1 to 64.4 km/h (10 to 40 mph)
    No large fluctuations when driving at a constant speed

    CAUTION:
    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

    HINT:
    Data can be captured relatively easily by using the snapshot function in the Data List. Confirm the data after performing the drive test.



NG
INSPECT FRONT OR REAR SPEED SENSOR
OK

END


← Starter Signal Circuit (from Jan 2017)MIL Circuit (from Jan 2017) →