2014-2019 Hiace · Service Manual ENGINE

P052F Glow Plug Control Module System Voltage

Diagnostic trouble codes · Vehicles built from Jan 2017

Also covers:

Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Nov 2015 Dec 2015 – Mar 2016 Apr 2016 – Dec 2016 from Jan 2017

DESCRIPTION

The glow system consists of the glow plug controller, glow plugs and ECM. The glow plug controller turns on the glow plug of each cylinder according to the duty command signal from the ECM in order to maintain optimal engine temperatures. The glow plugs can be controlled according to the engine coolant temperature at engine start by using duty signals. This helps induce ignition under low temperatures and prevent rough idle after starting the engine.
The glow plugs are turned on during PM forced regeneration in order to prevent the engine speed from rising due to an increase in fuel injection volume used to increase the exhaust gas temperature. The glow plug controller contains a self-diagnosis function. When the glow plug controller detects an internal malfunction, it sends a signal indicating the malfunction to the ECM.
P052F 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Enter check mode
The glow plug controller recognizes the battery voltage as being 18.4 V or higher 3 times or more when the glow plugs are on.
  1. 1 trip detection logic (Not OBD compliant*)
  2. 2 trip detection logic (EOBD (Euro OBD)*)
Glow plug controller
P0683 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Enter check mode
When the glow plugs are on, the ECM detects that there is no output from the glow plug control unit for 3 seconds even though the ECM outputs an SI signal ("ON" command signal).
  1. 1 trip detection logic (EOBD (Euro OBD)*)
  2. 2 trip detection logic (Not OBD compliant*)
  1. Open or short circuit in ground wire
  2. Open or short circuit in battery wire
  3. Open in SI wire
  4. SI wire short circuit to ground or battery
  5. Open in DI wire
  6. DI wire short circuit to ground or battery
  7. Low battery voltage
  8. Glow plug controller
  9. ECM
*: Check the "OBD Requirements" in the Data List.

WIRING DIAGRAM

A265668E03

INSPECTION PROCEDURE

NOTICE:
  1. Inspect the fuses of circuits related to this system before performing the following inspection procedure.
  2. After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).
  3. After replacing the fuel supply pump assembly, the ECM needs initialization (Click here).
  4. After replacing an injector assembly, the ECM needs registration (Click here).

HINT:
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


1. CHECK DTC OUTPUT
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON and turn the GTS on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the DTCs.

    Result 
    Result
    Proceed to
    P0683 is output
    A
    P052F is output
    B



B
Go to step 12
A


2. CHECK GLOW PLUG CONTROLLER (POWER SOURCE CIRCUIT)

  1. A241954E06
    Disconnect the glow plug controller connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    B67-4 (+B) - Body ground
    Ignition switch ON
    11 to 14 V
    B67-4 (+B) - Body ground
    Ignition switch off
    Below 0.5 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Glow Plug Controller)

  1. Reconnect the glow plug controller connector.



NG
Go to step 5
OK


3. CHECK HARNESS AND CONNECTOR (GLOW PLUG CONTROLLER - BODY GROUND)
  1. Disconnect the glow plug controller connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    B67-1 (GND) - Body ground
    Always
    Below 1 Ω

  1. Reconnect the glow plug controller connector.



NG
Go to step 7
OK


4. CHECK HARNESS AND CONNECTOR (GLOW PLUG CONTROLLER - ECM)
  1. Disconnect the glow plug controller connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    B67-3 (SI) - D99-57 (GLDO)
    Always
    Below 1 Ω
    B67-5 (DI) - D99-56 (GLDI)
    Always
    Below 1 Ω
    B67-3 (SI) or D99-57 (GLDO) - Body ground
    Always
    10 kΩ or higher
    B67-5 (DI) or D99-56 (GLDI) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the glow plug controller connector.

  1. Reconnect the ECM connector.



OK
Go to step 8

NG
Go to step 7
5. CHECK HARNESS AND CONNECTOR (GLOW PLUG CONTROLLER - NO. 1 INTEGRATION RELAY)
  1. Disconnect the glow plug controller connector.

  1. Remove the No. 1 integration relay from the No. 1 engine room relay block and junction block assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    B67-4 (+B) - 10B-4
    Always
    Below 1 Ω
    B67-4 (+B) or 10B-4 - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the glow plug controller connector.

  1. Reinstall the No. 1 integration relay



NG
Go to step 7
OK


6. CHECK CHARGING SYSTEM
  1. Check the charging system and perform repairs as necessary (Click here).



NEXT
Go to step 13
7. REPAIR OR REPLACE HARNESS OR CONNECTOR
  1. Repair or replace the harness or connector.



NEXT
Go to step 13
8. REPLACE GLOW PLUG CONTROLLER
  1. Replace the glow plug controller (Click here).


NEXT


9. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. Connect the GTS to the DLC3.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off for 30 seconds or more.

  1. Turn the ignition switch to ON.

  1. Turn the GTS on.

  1. Using the GTS, switch the ECM from normal mode to check mode (Click here).

  1. Confirm that the DTC is not output again.

    HINT:
    Check for DTCs in check mode.



NG
Go to step 10
OK

END

10. REPLACE ECM
  1. Replace the ECM (Click here).


NEXT


11. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. Connect the GTS to the DLC3.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off for 30 seconds or more.

  1. Turn the ignition switch to ON.

  1. Turn the GTS on.

  1. Using the GTS, switch the ECM from normal mode to check mode (Click here).

  1. Confirm that the DTC is not output again.

    HINT:
    Check for DTCs in check mode.


NEXT

END

12. REPLACE GLOW PLUG CONTROLLER
  1. Replace the glow plug controller (Click here)


NEXT


13. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. Connect the GTS to the DLC3.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off for 30 seconds or more.

  1. Turn the ignition switch to ON.

  1. Turn the GTS on.

  1. Using the GTS, switch the ECM from normal mode to check mode (Click here).

  1. Confirm that the DTC is not output again.

    HINT:
    Check for DTCs in check mode.


NEXT

END


← P052F Glow Plug Control Module System Voltage (+ P0683) (Apr 2016 – Dec 2016)P0545 Exhaust Gas Temperature Sensor Circuit Low (Bank 1 Sensor 1) (+ 5 more codes) (Oct 2014 – Dec 2014) →