2014-2019 Hiace · Service Manual ENGINE

P244B Diesel Particulate Filter Differential Pressure Too High

Diagnostic trouble codes · Vehicles built Dec 2015 – Mar 2016

Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Nov 2015 Dec 2015 – Mar 2016 Apr 2016 – Dec 2016 from Jan 2017

DESCRIPTION

Refer to DTC P244A (Click here).
P244B 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Engine is running at 4000 rpm with no load for 10 seconds or more.
While driving, Catalyst Differential Pressure becomes more than 0.27 for 3 seconds.
(1 trip detection logic)
  1. Front exhaust pipe assembly (DPF catalyst)
  2. Differential pressure sensor assembly
Common Inspection Item:
  1. Fuel injection system
  2. Intake/Exhaust system
  3. After treatment control system
Related Data List 
DTC No.
Data List
P244B
  1. DPF Differential Pressure
  2. Catalyst Differential Press
  3. Exhaust Fuel Addition FB

MONITOR DESCRIPTION

The ECM compares pressure upstream and downstream of the DPF catalyst to monitor the differential pressure. If the differential pressure is large, the ECM determines that the DPF catalyst is contaminated or has deteriorated and illuminates the MIL.
A244057E02

INSPECTION PROCEDURE

NOTICE:
  1. After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).
  2. After replacing the fuel supply pump assembly, the ECM needs initialization (Click here).
  3. After replacing an injector assembly, the ECM needs registration (Click here).

HINT:
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


1. READ OUTPUT DTC (RECORD STORED DTC AND FREEZE FRAME DATA)
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON and turn the GTS on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Record the stored DTC and freeze frame data.

  1. Check Exhaust Fuel Addition FB and Catalyst Differential Press in the freeze frame data.

    HINT:
    1. When the Exhaust Fuel Addition FB value is 1.41 or more, it indicates a high possibility of insufficient temperature increase during PM forced regeneration.
    2. When the Catalyst Differential Press value is 0.27 or more, it indicates a high possibility that DPF catalyst is clogged.


NEXT


2. CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P244B)
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the GTS on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the DTCs.

    Result 
    Result
    Proceed to
    P244B is output
    A
    P244B is output at the same time as P2463*
    Other relevant DTCs are output
    B

    HINT:
    *: When P244B is output at the same time as P2463, perform this diagnostic procedure. When DTC P244B is not output at the same time as P2463 is output, perform the diagnostic procedure for P244C (Click here).



B
Go to step 9
A


3. READ VALUE USING GTS (DPF DIFFERENTIAL PRESSURE)
  1. Connect the GTS to the DLC3.

  1. Start the engine and turn the GTS on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / DPF Differential Pressure.

  1. Check the DPF Differential Pressure values from idle speed to unloaded maximum engine speed.

    Result 
    Result
    Proceed to
    DPF Differential Pressure increases as engine speed increases from idle speed
    A
    Except above
    B
    A241154E05

    HINT:
    If DPF Differential Pressure indicates negative pressure for approx. 1 second as shown in the illustration (A) when the engine speed increases, the differential pressure sensor piping of the DPF catalyst may be clogged.



A
Go to step 5
B


4. CLEAN OR REPLACE VACUUM TRANSMITTING HOSE
  1. Even though it has been determined that the vacuum transmitting hose needs to be repaired or cleaned, make sure to perform all diagnostic procedures for DTC P244B before repairing or cleaning it.



NEXT
Go to step 5
5. CHECK FOR BLACK SMOKE
  1. Start the engine and drive the vehicle until the engine coolant temperature reaches 60°C (140°F) or higher.

  1. Stop the vehicle and allow the engine to idle.

  1. Fully depress the accelerator pedal for 5 seconds, and then release it [A].

  1. Repeat the above procedure [A] 10 times [B].

  1. Check for black smoke emission during procedures [A] and [B].

    OK:
    Black smoke is emitted less than 5 times.

    HINT:
    Even if the black smoke is very thin, count the number of black smoke emissions if there is any visible smoke.



NG
Go to step 8
OK


6. READ VALUE USING GTS (CATALYST DIFFERENTIAL PRESS)
  1. Connect the GTS to the DLC3.

  1. Start the engine and turn the GTS on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Catalyst Differential Press.

  1. Check the value of Catalyst Differential Press at 4000 rpm without load.

    Result 
    Result
    Proceed to
    Catalyst Differential Press is more than 0.27
    A
    Except above
    B



A
Go to step 8
B


7. PERFORM PM FORCED REGENERATION
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON and turn the GTS on.

  1. Clear the DTCs (Click here).

  1. Perform PM forced regeneration (Click here).

    Result:
    PM forced regeneration completes normally.



NG
Go to step 10
OK

END

8. REPLACE FRONT EXHAUST PIPE ASSEMBLY
Even though it has been determined that the front exhaust pipe assembly (DPF catalyst) needs to be replaced, make sure to perform all diagnostic procedures for DTC P244B before replacing it.


NEXT
Go to step 10
9. GO TO DTC CHART
  1. Perform inspection and repair of relevant DTCs (Click here).


NEXT


10. CHECK FUEL INJECTION SYSTEM
  1. Check the fuel injection system (Click here).


NEXT


11. CHECK INTAKE / EXHAUST SYSTEM
  1. Check the intake/exhaust system (Click here).


NEXT


12. CHECK AFTER TREATMENT CONTROL SYSTEM
  1. Check the after treatment control system (Click here).


NEXT


13. REPAIR OR REPLACE MALFUNCTIONING PARTS

HINT:
Repair, replace or clean the following items only when it has been determined necessary based on diagnosis for DTC P244B.

  1. Clean and/or repair the hoses of the differential pressure sensor.

  1. Replace the front exhaust pipe assembly (DPF catalyst) (Click here).

    NOTICE:
    Perform Initialization procedure for DPF catalyst record clear (Click here).


NEXT


14. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON and turn the GTS on.

  1. Clear the DTCs (Click here).

  1. Perform PM forced regeneration (Click here).


NEXT

END


← P244B Diesel Particulate Filter Differential Pressure Too High (Jan 2015 – Nov 2015)P244B Diesel Particulate Filter Differential Pressure Too High (Apr 2016 – Dec 2016) →