B1507 Open in Turn Signal Circuit
Diagnostic trouble codes · Vehicles built from Jan 2015
Also covers:
- B1508 Short in Turn Signal / Hazard Flasher Circuit
Versions by build date: Oct 2014 – Dec 2014 from Jan 2015
DESCRIPTION
These DTCs are stored when the combination meter assembly detects an open in a turn signal light circuit, a short in a turn signal light circuit, or a short in the hazard warning light circuit.| DTC Code |
DTC Detection Condition |
Trouble Area |
| B1507 |
When IG voltage is 9.5 V or more and the following condition is detected:
|
|
| B1508 |
When IG voltage is 9.5 V or more and the following condition is detected:
|
WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- Inspect the bulbs for circuits related to this system before performing the following inspection procedure.
| 1. CHECK FOR DTC |
Clear the DTCs (Click here).
Check for DTCs (Click here).
- OK:
- DTC B1507 or B1508 output does not occur.
|
|
||||
| OK | ||
| ||
| 2. CHECK HARNESS AND CONNECTOR (COMBINATION METER - FRONT TURN SIGNAL LIGHT SOCKET LH, REAR COMBINATION LIGHT SOCKET AND WIRE LH AND BODY GROUND) |
Disconnect the H71 combination meter assembly connector.
Disconnect the A23 front turn signal light socket assembly LH connector
Disconnect the T16 rear combination light socket and wire sub-assembly LH connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
H71-13 (LL) - A23-2
Always
Below 1 Ω
H71-13 (LL) - T16-4
Always
Below 1 Ω
A23-1 - Body ground
Always
Below 1 Ω
T16-6 - Body ground
Always
Below 1 Ω
H71-13 (LL) or A23-2 - Body ground
Always
10 kΩ or higher
H71-13 (LL) or T16-4 - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 3. CHECK HARNESS AND CONNECTOR (COMBINATION METER - FRONT TURN SIGNAL LIGHT SOCKET RH, REAR COMBINATION LIGHT SOCKET AND WIRE RH AND BODY GROUND) |
Disconnect the H71 combination meter assembly connector.
Disconnect the A1 front turn signal light socket assembly RH connector
Disconnect the T33*1 or U1*2 rear combination light socket and wire sub-assembly LH connector.
- *1: except Grade Super GL
- *2: for Grade Super GL
- *1: except Grade Super GL
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
- except Grade Super GL:
Tester Connection
Condition
Specified Condition
H71-7 (LR) - A1-2
Always
Below 1 Ω
H71-7 (LR) - T33-4
Always
Below 1 Ω
A1-1 - Body ground
Always
Below 1 Ω
T33-6 - Body ground
Always
Below 1 Ω
H71-7 (LR) or A1-2 - Body ground
Always
10 kΩ or higher
H71-7 (LR) or T33-4 - Body ground
Always
10 kΩ or higher
- for Grade Super GL:
Tester Connection
Condition
Specified Condition
H71-7 (LR) - A1-2
Always
Below 1 Ω
H71-7 (LR) - U1-4
Always
Below 1 Ω
A1-1 - Body ground
Always
Below 1 Ω
U1-6 - Body ground
Always
Below 1 Ω
H71-7 (LR) or A1-2 - Body ground
Always
10 kΩ or higher
H71-7 (LR) or U1-4 - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 4. CHECK FRONT TURN SIGNAL LIGHT SOCKET |
Temporarily replace the front turn signal light socket with a new or normally functioning one.
- for LED Headlight: Click here
- for Halogen Headlight: Click here
- for LED Headlight: Click here
Clear the DTCs (Click here).
Check for DTCs (Click here).
- OK:
- No DTCs are output.
|
|
||||
| OK | ||
| ||
| 5. CHECK REAR COMBINATION LIGHT SOCKET AND WIRE SUB-ASSEMBLY |
Temporarily replace the rear combination light socket and wire sub-assembly with a new or normally functioning one (Click here)
Clear the DTCs (Click here).
Check for DTCs (Click here).
- OK:
- No DTCs are output.
|
|
||||
| OK | ||
| ||
