2014-2019 Hiace · Service Manual ENGINE

P2141 Diesel Throttle Motor Circuit Low

Diagnostic trouble codes · Vehicles built from Jan 2017

Also covers:

DESCRIPTION

The throttle actuator is operated by the ECM and opens and closes the throttle valve using gears. The opening angle of the throttle valve is detected by the throttle position sensor, which is mounted on the diesel throttle body assembly.
P2141 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Idle the engine for 5 seconds or more
Both of the following conditions are met for 2.0 seconds (1 trip detection logic):
(1 trip detection logic)
  1. The throttle actuator duty cycle is 80% or higher.
  2. The throttle actuator current is less than 0.5 A.
  1. Open or short in throttle actuator circuit
  2. Diesel throttle body assembly
  3. ECM
P2142 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Idle the engine for 5 seconds or more
A throttle actuator current of 8 A or higher or the ECM internal circuit temperature of 150 to 160°C (302 to 320°F) or higher is detected.
(1 trip detection logic)
  1. Open or short in throttle actuator circuit
  2. Diesel throttle body assembly
  3. ECM
Related Data List 
DTC No.
Data List
P2141
P2142
Throttle Motor DUTY

WIRING DIAGRAM

A348546E02

INSPECTION PROCEDURE

NOTICE:
After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).

HINT:
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


1. INSPECT DIESEL THROTTLE BODY ASSEMBLY
  1. Remove the diesel throttle body assembly. (Click here).

  1. A327312E04
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    4 (M-) - 1 (M+)
    Always
    No short or no open circuit

    Text in Illustration 
    *a
    Component without harness connected
    (Diesel Throttle Body Assembly)



NG
REPLACE DIESEL THROTTLE BODY ASSEMBLY (Click here)
OK


2. CHECK HARNESS AND CONNECTOR (DIESEL THROTTLE BODY ASSEMBLY - ECM)
  1. Disconnect the diesel throttle body assembly connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D119-1 (M+) - D134-48 (M+)
    Always
    Below 1 Ω
    D119-4 (M-) - D134-18 (M-)
    Always
    Below 1 Ω
    D119-1 (M+) or D134-48 (M+) - Body ground and other terminals
    Always
    10 kΩ or higher
    D119-4 (M-) or D134-18 (M-) - Body ground and other terminals
    Always
    10 kΩ or higher

  1. Reconnect the diesel throttle body assembly connector.



NG
Go to step 4
OK


3. REPLACE ECM
  1. Replace the ECM (Click here).



NEXT
Go to step 5
4. REPAIR OR REPLACE HARNESS OR CONNECTOR
  1. Repair or replace the harness or connector.


NEXT


5. CHECK CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON and turn the GTS on.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off and wait for 30 seconds.

  1. Start the engine.

  1. Idle the engine for 5 seconds or more.

  1. Turn the GTS on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Confirm that the DTC is not output.


NEXT

END


← P2121 Throttle / Pedal Position Sensor / Switch "D" Circuit Range / Performance (from Jan 2017)P2195 Oxygen (A/F) Sensor Signal Stuck Lean (Bank 1 Sensor 1) (from Jan 2017) →