2014-2019 Hiace · Service Manual ENGINE

P2121 Throttle / Pedal Position Sensor / Switch "D" Circuit Range / Performance

Diagnostic trouble codes · Vehicles built from Jan 2017

DESCRIPTION

Refer to DTC P2120 (Click here).
P2121 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Ignition switch ON for 5 seconds or more.
  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Accel Sens. No.1 Volt %, and Accel Sens. No.2 Volt %.
  2. Slowly depress the accelerator pedal until Accel Sens. No.1 Volt % is approximately 30% and Accel Sens. No.2 Volt % is approximately 46%, then slowly release the accelerator pedal.
Either of the following conditions is met (1 trip detection logic):
  1. Difference between VPA and VPA2 is less than 0.4 V, or higher than 1.2 V. (learned value of accelerator off position)
  2. Difference between VPA and VPA2 is greater than or equal to the specified value.
  1. Accelerator pedal sensor assembly
  2. ECM
Related Data List 
DTC No.
Data List
P2121
  1. Accel Position
  2. Accel Sens. No.1 Volt %
  3. Accel Sens. No.2 Volt %

WIRING DIAGRAM

Refer to DTC P2120 (Click here).

INSPECTION PROCEDURE

NOTICE:
After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).

HINT:
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


1. READ VALUE USING GTS (ACCELERATOR PEDAL POSITION SENSOR)

  1. C129061E03
    Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON and turn the GTS on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Accel Sens. No.1 Volt % and Accel Sens. No.2 Volt %.

  1. Read the values.

    Standard Voltage:
    Accelerator Pedal
    Accel Sens. No.1 Volt %
    Accel Sens. No.2 Volt %
    Released
    10 to 22%
    24 to 40%
    Depressed
    52 to 90%
    68 to 99%

    Text in Illustration 
    *1
    Accelerator Pedal Assembly
    *a
    Depressed
    *b
    Released
    Result 
    Result
    Proceed to
    NG
    A
    OK
    B



OK
Go to step 5
NG


2. REPLACE ACCELERATOR PEDAL SENSOR ASSEMBLY
  1. Replace the accelerator pedal sensor assembly (Click here).


NEXT


3. CHECK WHETHER DTC OUTPUT RECURS (DTC P2121)
  1. Connect the GTS to the DLC3.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off and wait for at least 30 seconds.

  1. Wait for 5 seconds after turning the ignition switch to ON.

  1. Turn the GTS on.

  1. Operate the accelerator pedal in accordance with the following procedure [B].

    1. Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / Accel Sens. No.1 Volt %, and Accel Sens. No.2 Volt %.

    2. Slowly depress the accelerator pedal until Accel Sens. No.1 Volt % is approximately 30% and Accel Sens. No.2 Volt % is approximately 46%, then slowly release the accelerator pedal.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the DTCs.

    Result 
    Result
    Proceed to
    DTC P2121 is output
    A
    No DTC is output
    B



B
END
A


4. REPLACE ECM
  1. Replace the ECM (Click here).


NEXT


5. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. Connect the GTS to the DLC3.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off and wait for at least 30 seconds.

  1. Wait for 5 seconds after turning the ignition switch to ON.

  1. Turn the GTS on.

  1. Operate the accelerator pedal in accordance with the following procedure [B].

    1. Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / Accel Sens. No.1 Volt %, and Accel Sens. No.2 Volt %.

    2. Slowly depress the accelerator pedal until Accel Sens. No.1 Volt % is approximately 30% and Accel Sens. No.2 Volt % is approximately 46%, then slowly release the accelerator pedal.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Confirm that the DTC is not output again.


NEXT

END


← P2120 Throttle / Pedal Position Sensor / Switch "D" Circuit (+ 6 more codes) (from Jan 2017)P2141 Diesel Throttle Motor Circuit Low (+ P2142) (from Jan 2017) →