2014-2019 Hiace · Service Manual ENGINE

P204C Reductant Pressure Sensor Circuit Low

Diagnostic trouble codes · Vehicles built from Jan 2017

Also covers:

DESCRIPTION

Refer to DTC P208B (Click here).
P204C 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Ignition switch ON for 3 seconds
An open or short circuit occurs in the pressure sensor circuit for 3 seconds or more.
(1 trip detection logic)
  1. Open or short in pressure sensor circuit
  2. Pressure sensor (Urea pump)
  3. Urea pump control ECU
P204D 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Ignition switch ON for 3 seconds
An open or short circuit occurs in the pressure sensor circuit for 3 seconds or more.
(1 trip detection logic)
  1. Open or short in pressure sensor circuit
  2. Pressure sensor (Urea pump)
  3. Urea pump control ECU
Related Data List 
DTC No.
Data List
P204C
P204D
Reductant Pressure

WIRING DIAGRAM

A357972E04

INSPECTION PROCEDURE

HINT:
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


1. READ VALUE USING GTS (REDUCTANT PRESSURE)
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON and turn the GTS on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Reductant Pressure.

  1. Read the Data List according to the display on the GTS.

    Result 
    Result
    Proceed to
    -50 kPa
    A
    900 kPa
    B



B
Go to step 9
A


2. READ VALUE USING GTS (CHECK FOR OPEN)

  1. A360358E02
    Disconnect the pressure sensor (urea pump) connector.

  1. Connect terminals 4 (VPSE) and 5 (PSE) of the pressure sensor (urea pump) wire harness side connector.

  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON and turn the GTS on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Reductant Pressure.

  1. Read the Data List according to the display on the GTS.

    OK:
    900 kPa
    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Pressure Sensor (Urea Pump))



NG
Go to step 6
OK


3. REPLACE UREA PUMP
  1. Replace the urea pump (Click here).


NEXT


4. CLEAR DTC
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON and turn the GTS on.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off and wait for at least 30 seconds.


NEXT


5. CHECK DTC OUTPUT
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON and wait for 3 seconds or more.

  1. Turn the GTS on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Confirm that the DTC is not output again.


NEXT

END

6. CHECK HARNESS AND CONNECTOR (PRESSURE SENSOR (UREA PUMP) - UREA PUMP CONTROL ECU)
A360342E14
Text in Illustration 
*a
Front view of wire harness connector
(to Pressure Sensor (Urea Pump))
*b
Front view of wire harness connector
(to Urea Pump Control ECU)
  1. Disconnect the pressure sensor (urea pump) connector.

  1. Disconnect the urea pump control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A47-4 (VPSE) - A45-57 (VCPU)
    Always
    Below 1 Ω
    A47-5 (PSE) - A45-56 (PU)
    Always
    Below 1 Ω
    A47-6 (EPSE) - A45-55 (EPU)
    Always
    Below 1 Ω
    A47-4 (VPSE) or A45-57 (VCPU) - Body ground and other terminals
    Always
    10 kΩ or higher
    A47-5 (PSE) or A45-56 (PU) - Body ground and other terminals
    Always
    10 kΩ or higher
    A47-6 (EPSE) or A45-55 (EPU) - Body ground and other terminals
    Always
    10 kΩ or higher



NG
Go to step 8
OK


7. REPLACE UREA PUMP CONTROL ECU
  1. Replace the urea pump control ECU (Click here).



NEXT
Go to step 4
8. REPAIR OR REPLACE HARNESS OR CONNECTOR
  1. Repair or replace harness or connector.



NEXT
Go to step 4
9. READ VALUE USING GTS (CHECK FOR SHORT)
  1. Disconnect the pressure sensor (urea pump) connector.

  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON and turn the GTS on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Reductant Pressure.

  1. Read the Data List according to the display on the GTS.

    OK:
    -50 kPa



OK
Go to step 4
NG


10. CHECK HARNESS AND CONNECTOR (PRESSURE SENSOR (UREA PUMP) - UREA PUMP CONTROL ECU)
A360342E14
Text in Illustration 
*a
Front view of wire harness connector
(to Pressure Sensor (Urea Pump))
*b
Front view of wire harness connector
(to Urea Pump Control ECU)
  1. Disconnect the pressure sensor (urea pump) connector.

  1. Disconnect the urea pump control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A47-4 (VPSE) - A45-57 (VCPU)
    Always
    Below 1 Ω
    A47-5 (PSE) - A45-56 (PU)
    Always
    Below 1 Ω
    A47-6 (EPSE) - A45-55 (EPU)
    Always
    Below 1 Ω
    A47-4 (VPSE) or A45-57 (VCPU) - Body ground and other terminals
    Always
    10 kΩ or higher
    A47-5 (PSE) or A45-56 (PU) - Body ground and other terminals
    Always
    10 kΩ or higher
    A47-6 (EPSE) or A45-55 (EPU) - Body ground and other terminals
    Always
    10 kΩ or higher



OK
Go to step 7

NG
Go to step 8

← P204B Reductant Pressure Sensor Circuit Range/Performance (from Jan 2017)P205B Reductant Tank Temperature Sensor Circuit Range/Performance (from Jan 2017) →