2014-2019 Hiace · Service Manual ENGINE

P20BB Reductant Heater "A" Control Circuit Low

Diagnostic trouble codes · Vehicles built from Jan 2017

Also covers:

DESCRIPTION

Refer to DTC P202B (Click here).
P20BB 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Reductant Pipe Heater (Active Test)
When the urea tube with heater is operating, an open or short circuit occurs in the urea tube with heater circuit for 3 seconds or more.
(1 trip detection logic)
  1. Open or short in urea tube with heater assembly circuit
  2. Urea tube with heater assembly
  3. Urea pump control ECU
P20BC 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Reductant Pipe Heater (Active Test)
When the urea tube with heater is operating, an open or short circuit occurs in the urea tube with heater circuit for 3 seconds or more.
(1 trip detection logic)
  1. Open or short in urea tube with heater assembly circuit
  2. Urea tube with heater assembly
  3. Urea pump control ECU
Related Data List 
DTC No.
Data List
P20BB
P20BC
Reductant Pipe Heater

WIRING DIAGRAM

A357971E06

INSPECTION PROCEDURE

HINT:
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


1. INSPECT UREA TUBE WITH HEATER ASSEMBLY
  1. Disconnect the urea tube with heater assembly connector.

  1. A402111E01
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    20°C (68°F)
    6.39 to 7.81 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (to Urea Tube with Heater Assembly)



NG
Go to step 9
OK


2. CHECK HARNESS AND CONNECTOR (UREA TUBE WITH HEATER ASSEMBLY - UREA PUMP CONTROL ECU)
A402112E01
Text in Illustration 
*a
Front view of wire harness connector
(to Urea Tube with Heater Assembly)
*b
Front view of wire harness connector
(to Urea Pump Control ECU)
  1. Disconnect the urea tube with heater assembly connector.

  1. Disconnect the urea pump control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.


Standard Resistance::
Tester Connection
Condition
Specified Condition
A46-2(HTUL) - A45-20(HTL)
Always
Below 1 Ω
A46-1(GND) - A45-32(EHTL)
Always
Below 1 Ω
A46-2(HTUL) or A45-20(HTL) - Body ground
Always
10 kΩ or higher
A46-1(GND) or A45-32(EHTL) - Body ground
Always
10 kΩ or higher



NG
Go to step 8
OK


3. CLEAR DTC
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON and turn the GTS on.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off and wait for 30 seconds or more.


NEXT


4. CHECK DTC OUTPUT
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON and turn the GTS on.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Reductant Pipe Heater.

  1. Perform the Active Test.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the DTCs.


Result:
Result
Proceed to
DTC P20BB or P20BC is output
A
DTCs is not output
B



B
END
A


5. REPLACE UREA PUMP CONTROL ECU
  1. Replace the urea pump control ECU (Click here).


NEXT


6. CLEAR DTC
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON and turn the GTS on.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off and wait for 30 seconds or more.


NEXT


7. CHECK DTC OUTPUT
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON and turn the GTS on.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Reductant Pipe Heater.

  1. Perform the Active Test.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Confirm that the DTC is not output again.


NEXT

END

8. REPAIR OR REPLACE HARNESS AND CONNECTOR
  1. Repair or replace the harness or connector.



NEXT
Go to step 6
9. REPLACE UREA TUBE WITH HEATER ASSEMBLY
  1. Replace the urea tube with heater assembly (Click here).



NEXT
Go to step 6

← P209F Reductant Tank Heater Control Circuit Performance (+ P20BA) (from Jan 2017)P20CD Open in Exhaust Aftertreatment Fuel Injector "A" Control Circuit (from Jan 2017) →