2014-2019 Hiace · Service Manual ENGINE

P2470 Exhaust Gas Temperature Sensor Circuit Low (Bank 1 Sensor 4)

Diagnostic trouble codes · Vehicles built from Jan 2017

Also covers:

DESCRIPTION

A362192E01
The No. 4 exhaust gas temperature sensor is installed after the SCR catalyst to detect the exhaust gas temperature. A thermistor built into the No. 4 exhaust gas temperature sensor changes its resistance value according to the exhaust gas temperature. The lower the exhaust gas temperature, the higher the thermistor resistance value. The higher the exhaust gas temperature, the lower the thermistor resistance value. The No. 4 exhaust gas temperature sensor is connected to the ECM. The 5 V power source voltage is applied to the No. 4 exhaust gas temperature sensor from terminal THSO via resistor R. Resistor R and the No. 4 exhaust gas temperature sensor are connected in series. When the resistance value of the No. 4 exhaust gas temperature sensor changes in accordance with the exhaust gas temperature, the voltage at terminal THSO also changes. The No. 4 exhaust gas temperature sensor monitors the temperature downstream of the SCR catalyst.
P2470 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Idle the engine for 3 seconds after warming up the engine (the engine coolant temperature is 70°C (158°F) or higher) and allowing 1 minute to elapse after starting the engine.
No. 4 Exhaust gas temperature sensor output voltage is below 0.11 V for 3 seconds or more when all conditions are met. (1 trip detection logic):
  1. After starting the engine, 1 minute or more elapses
  2. Engine is running
  3. Coolant temperature is 70°C (158°F) or higher
  1. Open or short in No. 4 exhaust gas temperature sensor circuit
  2. No. 4 exhaust gas temperature sensor
  3. ECM
P2471 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Idle the engine for 3 seconds after warming up the engine (the engine coolant temperature is 70°C (158°F) or higher) and allowing 1 minute to elapse after starting the engine.
No. 4 Exhaust gas temperature sensor output voltage is higher than 4.89 V for 3 seconds or more when all conditions are met. (1 trip detection logic):
  1. After starting the engine, 1 minute or more elapses
  2. Engine is running
  3. Coolant temperature is 70°C (158°F) or higher
  1. Open or short in No. 4 exhaust gas temperature sensor circuit
  2. No. 4 exhaust gas temperature sensor
  3. ECM
Related Data List 
DTC No.
Data List
P2470
P2471
SCR Temperature

MONITOR DESCRIPTION

The ECM constantly monitors the output voltages from the No. 4 exhaust gas temperature sensors in order to detect problems with the sensors. When the sensor output voltage deviates from the normal operating range (between 0.11 V and 4.89 V) for more than 3 seconds after the engine is warmed up, the ECM interprets this as malfunction of the sensor circuit and illuminates the MIL.

WIRING DIAGRAM

A356866E02

INSPECTION PROCEDURE

HINT:
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


1. INSPECT NO. 4 EXHAUST GAS TEMPERATURE SENSOR
  1. Inspect the No. 4 exhaust gas temperature sensor (Click here).



NG
Go to step 4
OK


2. CHECK HARNESS AND CONNECTOR (NO. 4 EXHAUST GAS TEMPERATURE SENSOR - ECM)
  1. Disconnect the No. 4 exhaust gas temperature sensor.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    r6-2 (THSO) - B97-38 (THSO)
    Always
    Below 1 Ω
    r6-1 (E2) - B97-54 (ETSO)
    Always
    Below 1 Ω
    r6-2 (THSO) or B97-38 (THSO) - Body ground and other terminals
    Always
    10 kΩ or higher
    r6-1 (E2) or B97-54 (ETSO) - Body ground and other terminals
    Always
    10 kΩ or higher

  1. Reconnect the No. 4 exhaust gas temperature sensor.

  1. Reconnect the ECM connector.



NG
Go to step 5
OK


3. REPLACE ECM
  1. Replace the ECM (Click here).



NEXT
Go to step 6
4. REPLACE NO. 4 EXHAUST GAS TEMPERATURE SENSOR
  1. Replace the No. 4 exhaust gas temperature sensor (Click here).



NEXT
Go to step 6
5. REPAIR OR REPLACE HARNESS OR CONNECTOR
  1. Repair or replace the harness or connector.


NEXT


6. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. Connect the GTS to the DLC3.

  1. Clear the DTCs (Click here).

  1. Start the engine.

  1. Idle the engine for 3 seconds or more after warming up the engine (the engine coolant temperature is 70°C (158°F) or higher) and allowing 1 minute to elapse after starting the engine.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Confirm that the DTC is not output again.


NEXT

END


← P245C Exhaust Gas Recirculation Cooler Bypass Control Circuit Low (+ P245D) (from Jan 2017)P2564 Turbocharger/Supercharger Boost Control Position Sensor "A" Circuit Low (+ P2565) (from Jan 2017) →