2014-2019 Hiace · Service Manual ENGINE

P2564 Turbocharger/Supercharger Boost Control Position Sensor "A" Circuit Low

Diagnostic trouble codes · Vehicles built from Jan 2017

Also covers:

DESCRIPTION

The variable nozzle vane type turbocharger consists primarily of a compressor wheel, turbine wheel, nozzle vane, unison ring, DC motor and nozzle vane position sensor.
The nozzle vane position sensor consists of a Hall IC and a magnetic yoke that rotates in unison with the movement of the linkage that actuates the nozzle vane. The nozzle vane position sensor converts the changes in the magnetic flux that are caused by the rotation of the DC motor (hence, the rotation of the magnetic yoke) into electric signals, and outputs them to the ECM. The ECM determines the actual nozzle vane position from the electric signals in order to calculate the target nozzle vane position.
A348993E01
P2564 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Ignition switch ON for 2 seconds or more
VNA voltage is 0.1 V or less for 2.1 seconds (1 trip detection logic).
  1. Nozzle vane position sensor (turbocharger nozzle vane control actuator)
  2. Open or short in nozzle vane position sensor circuit
  3. ECM
P2565 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Ignition switch ON for 2 seconds or more
VNA voltage is 4.9 V or higher for 2.1 seconds (1 trip detection logic).
  1. Nozzle vane position sensor (turbocharger nozzle vane control actuator)
  2. Open or short in nozzle vane position sensor circuit
  3. ECM

HINT:
If DTC P2564 and/or P2565 is stored due to the nozzle vane being stuck open, the following symptoms may appear:
  1. - Lack of power
  2. - Vehicle surge or hesitation under light or medium load


WIRING DIAGRAM

A348545E03

INSPECTION PROCEDURE

NOTICE:
After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).

HINT:
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


1. CHECK HARNESS AND CONNECTOR (NOZZLE VANE POSITION SENSOR - ECM)
  1. Disconnect the nozzle vane position sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D122-1 (VNVC) - D134-96 (VNVC)
    Always
    Below 1 Ω
    D122-3 (VTA1) - D134-94 (VNA)
    Always
    Below 1 Ω
    D122-2 (VNE2) - D134-95 (VNE2)
    Always
    Below 1 Ω
    D122-1 (VNVC) - D134-96 (VNVC) - Body ground and other terminals
    Always
    10 kΩ or higher
    D122-3 (VTA1) or D134-94 (VNA) - Body ground and other terminals
    Always
    10 kΩ or higher
    D122-2 (VNE2) or D134-95 (VNE2) - Body ground and other terminals
    Always
    10 kΩ or higher

  1. Reconnect the nozzle vane position sensor connector.

  1. Reconnect the ECM connector.



NG
Go to step 6
OK


2. CHECK TERMINAL VOLTAGE (POWER SOURCE OF NOZZLE VANE POSITION SENSOR)

  1. C129053E48
    Disconnect the nozzle vane position sensor connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    D122-1 (VNVC) - D122-2 (VNE2)
    Ignition switch ON
    4.5 to 5.5 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Nozzle Vane Position Sensor)

  1. Reconnect the nozzle vane position sensor connector.



NG
Go to step 5
OK


3. CHECK ECM (CHECK RESISTANCE)

  1. C129053E49
    Disconnect the nozzle vane position sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D122-1 (VNVC) - D122-3 (VTA1)
    Ignition switch off
    No short or no open circuit
    D122-3 (VTA1) - D122-2 (VNE2)

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Nozzle Vane Position Sensor)

  1. Reconnect the nozzle vane position sensor connector.



NG
Go to step 5
OK


4. REPLACE TURBOCHARGER NOZZLE VANE CONTROL ACTUATOR (NOZZLE VANE POSITION SENSOR)
  1. Replace the turbocharger nozzle vane control actuator (Click here).



NEXT
Go to step 7
5. REPLACE ECM
  1. Replace the ECM (Click here).



NEXT
Go to step 7
6. REPAIR OR REPLACE HARNESS OR CONNECTOR
  1. Repair or replace the harness or connector.


NEXT


7. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. Connect the GTS to the DLC3.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off and leave the vehicle for 15 seconds.

  1. Turn the ignition switch to ON for 2 seconds or more.

  1. Confirm that the DTC is not output again.

    HINT:
    Perform the following procedure using the GTS to determine whether or not the DTC judgment has been carried out.

    1. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

    2. Input DTC P2564 and/or P2565.

    3. Check that STATUS is NORMAL. If STATUS is INCOMPLETE or N/A, idle the engine.


NEXT

END


← P2470 Exhaust Gas Temperature Sensor Circuit Low (Bank 1 Sensor 4) (+ P2471) (from Jan 2017)P2610 ECM / PCM Internal Engine Off Timer Performance (from Jan 2017) →