The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the cylinder head gasket removal/installation are shown below.
When the cable is disconnected / reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
Learning completes when vehicle is operated normally
| *a | An Object Exceeding Weight Limit of Engine Lifter |
The engine assembly with transmission is very heavy. Be sure to follow the procedure described in the repair manual, or the engine lifter may suddenly drop or the engine assembly may fall off the engine lifter.
To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.
11310
1.REMOVE TIMING CHAIN COVER ASSEMBLY
2.SET NO. 1 CYLINDER TO TDC/COMPRESSION
13540
3.REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY
13559
4.REMOVE CHAIN TENSIONER SLIPPER
13506
5.REMOVE CHAIN SUB-ASSEMBLY
6.REMOVE CAMSHAFT TIMING GEARS AND NO. 2 CHAIN SUB-ASSEMBLY (for Bank 1)
| *a | Pin |
| *b | Plunger |
| *c | Push |
While raising the No. 2 chain tensioner assembly, insert a pin of 1.0 mm (0.0394 in.) diameter into the hole to hold the No. 2 chain tensioner assembly.
| *a | Turn |
| *b | Hold |
Using a wrench to hold the hexagonal portion of each camshaft, loosen the camshaft timing gear bolts of the camshaft timing gear assembly and the camshaft timing exhaust gear assembly.
Be careful not to damage the cylinder head with the wrench.
Do not loosen the other bolts. If any of the bolts is loosened, replace the camshaft timing gear assembly and/or the camshaft timing exhaust gear assembly with a new one.
Remove the 2 bolts and the camshaft timing gear assembly together with the No. 2 chain sub-assembly.
13550
7.REMOVE NO. 2 CHAIN TENSIONER ASSEMBLY
Remove the bolt and No. 2 chain tensioner assembly.
8.REMOVE CAMSHAFT BEARING CAP (for Bank 1)
| *1 | Knock Pin |
| *a | IN |
| *b | EX |
Check that the camshafts are positioned as shown in the illustration.
Uniformly loosen and remove the 9 camshaft bearing cap bolts in several steps and in the sequence shown in the illustration.
Uniformly loosen and remove the 15 camshaft bearing cap bolts in several steps and in the sequence shown in the illustration.
Uniformly loosen the bolts while keeping the camshaft level.
Remove the 5 camshaft bearing caps.
23476
9.REMOVE FUEL PUMP LIFTER HOUSING
Remove the fuel pump lifter housing.
13511
10.REMOVE CAMSHAFT
13512
11.REMOVE NO. 2 CAMSHAFT
11103C
12.REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY RH
| *a | Protective Tape |
Remove the camshaft housing sub-assembly RH by prying between the cylinder head sub-assembly and camshaft housing sub-assembly RH with a screwdriver.
Be careful not to damage the contact surfaces of the cylinder head sub-assembly and camshaft housing sub-assembly RH.
Tape the screwdriver tip before use.
13.REMOVE CAMSHAFT TIMING GEARS AND NO. 2 CHAIN SUB-ASSEMBLY (for Bank 2)
| *a | Pin |
| *b | Plunger |
| *c | Push |
While pushing down the No. 3 chain tensioner assembly, insert a pin of 1.0 mm (0.0394 in.) diameter into the hole to hold the No. 3 chain tensioner assembly.
| *a | Turn |
| *b | Hold |
Using a wrench to hold the hexagonal portion of each camshaft, loosen the camshaft timing gear bolts of the camshaft timing gear assembly and the camshaft timing exhaust gear assembly.
Be careful not to damage the cylinder head with the wrench.
Do not loosen the other bolts. If any of the bolts is loosened, replace the camshaft timing gear assembly and/or the camshaft timing exhaust gear assembly with a new one.
Remove the 2 bolts and the camshaft timing gear assembly together with the No. 2 chain sub-assembly.
13560A
14.REMOVE NO. 3 CHAIN TENSIONER ASSEMBLY
Remove the bolt and No. 3 chain tensioner assembly.
15.REMOVE CAMSHAFT BEARING CAP (for Bank 2)
| *1 | Knock Pin |
| *a | IN |
| *b | EX |
Check that the camshafts are positioned as shown in the illustration.
Uniformly loosen and remove the 8 camshaft bearing cap bolts in several steps and in the sequence shown in the illustration.
Uniformly loosen and remove the 13 camshaft bearing cap bolts in several steps and in the sequence shown in the illustration.
Uniformly loosen the bolts while keeping the camshaft level.
Remove the 5 camshaft bearing caps.
13053
16.REMOVE NO. 3 CAMSHAFT SUB-ASSEMBLY
13054
17.REMOVE NO. 4 CAMSHAFT SUB-ASSEMBLY
11104A
18.REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY LH
| *a | Protective Tape |
Remove the camshaft housing sub-assembly LH by prying between the cylinder head LH and camshaft housing sub-assembly LH with a screwdriver.
Be careful not to damage the contact surfaces of the cylinder head LH and camshaft housing sub-assembly LH.
Tape the screwdriver tip before use.
13561
19.REMOVE NO. 1 CHAIN VIBRATION DAMPER
13562
20.REMOVE NO. 2 CHAIN VIBRATION DAMPER
13801
21.REMOVE NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY
Remove the 24 No. 1 valve rocker arm sub-assemblies.
Arrange the removed parts in the correct order.
13750
22.REMOVE VALVE LASH ADJUSTER ASSEMBLY
Remove the 24 valve lash adjuster assemblies from the cylinder head sub-assembly and cylinder head LH.
Arrange the removed parts in the correct order.
13716
23.REMOVE VALVE STEM CAP
Remove the 24 valve stem caps.
Arrange the removed parts in the correct order.
16356
24.REMOVE REAR WATER BY-PASS JOINT
23802B
25.REMOVE NO. 2 FUEL PIPE SUB-ASSEMBLY
23860
26.REMOVE FUEL DELIVERY WITH SENSOR PIPE ASSEMBLY LH
23814E
27.REMOVE FUEL DELIVERY PIPE RH
23250E
28.REMOVE DIRECT FUEL INJECTOR ASSEMBLY
23255A
29.REMOVE FUEL INJECTOR SEAL
11101
30.REMOVE CYLINDER HEAD SUB-ASSEMBLY
Using a 10 mm bi-hexagon wrench, uniformly loosen the 8 bolts in the sequence shown in the illustration. Remove the 8 cylinder head bolts and plate washers.
Be careful not to drop washers into the cylinder head sub-assembly.
Cylinder head warpage or cracking could result from removing bolts in an incorrect order.
Be sure to keep separate the removed parts for each installation position.
Remove the cylinder head sub-assembly.
11115
31.REMOVE CYLINDER HEAD GASKET
11102
32.REMOVE CYLINDER HEAD LH
Uniformly loosen and remove the bolts in the sequence shown in the illustration.
Using a 10 mm bi-hexagon wrench, uniformly loosen the 8 bolts in the sequence shown in the illustration. Remove the 8 cylinder head bolts and plate washers.
Be careful not to drop washers into the cylinder head LH.
Cylinder head warpage or cracking could result from removing bolts in an incorrect order.
Be sure to keep separate the removed parts for each installation position.
Remove the cylinder head LH.
11116
33.REMOVE NO. 2 CYLINDER HEAD GASKET
11101A
34.INSPECT CYLINDER HEAD SET BOLT