Home › Engine / Hybrid System › 7GR-FKS (ENGINE MECHANICAL) › ENGINE UNIT › 2019.02–2020.06
RM35X0E _51 Engine / Hybrid System _078603 7GR-FKS ENGINE MECHANICAL _0381344 ENGINE UNIT A

7GR-FKS ENGINE MECHANICAL  ENGINE UNIT  DISASSEMBLY  


PROCEDURE

Hide 12185 1.REMOVE OIL FILLER CAP HOUSING

a.
A362031

Remove the oil filler cap sub-assembly.


b.

Remove the 2 nuts, oil filler cap housing assembly and gasket.


Hide 12101A 3.REMOVE OIL PAN DRAIN PLUG

a.

Remove the oil pan drain plug and gasket.


Hide 12601B 4.REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY (w/o Secondary Air Injection System)

Hide 12601B 5.REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY (w/o Secondary Air Injection System)

a.
A443669

Remove the 2 clips and No. 1 engine cover sub-assembly.


Hide 12204 6.REMOVE PCV VALVE SUB-ASSEMBLY

Hide 15370B 7.REMOVE CAMSHAFT TIMING OIL CONTROL SOLENOID ASSEMBLY (for Intake Side of Bank 1)

Hide 15370B 8.REMOVE CAMSHAFT TIMING OIL CONTROL SOLENOID ASSEMBLY (for Exhaust Side of Bank 1)

Hide 15370C 9.REMOVE CAMSHAFT TIMING OIL CONTROL SOLENOID ASSEMBLY (for Intake Side of Bank 2)

Hide 15370C 10.REMOVE CAMSHAFT TIMING OIL CONTROL SOLENOID ASSEMBLY (for Exhaust Side of Bank 2)

Hide 11.REMOVE VVT SENSOR (for Intake Side of Bank 1)

Hide 12.REMOVE VVT SENSOR (for Exhaust Side of Bank 1)

Hide 13.REMOVE VVT SENSOR (for Intake Side of Bank 2)

Hide 14.REMOVE VVT SENSOR (for Exhaust Side of Bank 2)

Hide 11401G 15.REMOVE CRANKSHAFT POSITION SENSOR

Hide 11415 16.REMOVE CYLINDER BLOCK WATER DRAIN COCK SUB-ASSEMBLY

a.
A443936C01
0.042,0.031 0.281,0.26 0.24,0.229 10 false *A 0.052,2.292 0.292,2.5 0.24,0.208 10 false *B
*A RH Side
*B LH Side


Remove the cylinder block water drain cock plug from the cylinder block water drain cock sub-assembly.


b.

Remove the water cylinder block water drain cock sub-assembly from the cylinder block sub-assembly.


c.

Remove the taper screw plug from the cylinder block sub-assembly.


Hide 17.REMOVE OIL FILTER ELEMENT

Hide 15609 18.REMOVE OIL FILTER BRACKET SUB-ASSEMBLY

Hide 15710 19.REMOVE OIL COOLER ASSEMBLY

Hide 13471 20.REMOVE CRANKSHAFT PULLEY

Hide 16031 21.REMOVE WATER INLET SUB-ASSEMBLY WITH THERMOSTAT

a.
A443937

Remove the 2 bolts, nut, water inlet sub-assembly with thermostat and gasket.


Hide 16331 22.REMOVE WATER OUTLET

a.
A443938

Remove the 2 bolts and water outlet.


b.
A443939

Remove the O-ring.


Hide 16356 23.REMOVE REAR WATER BY-PASS JOINT

a.
A443940

Detach the 2 clamps and disconnect the No. 5 engine wire.


b.
A443941

Remove the 4 bolts, 2 nuts and rear water by-pass joint.


c.
A443942

Remove the O-ring from the No. 1 water outlet pipe.


d.
A443943

Remove the 2 O-rings from the rear water by-pass joint.


Hide 24.REMOVE FUEL PUMP SPACER GASKET

a.

Remove the fuel pump spacer gasket from the cylinder head cover sub-assembly.


Hide 11201 25.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

Hide 11202 26.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY LH

Hide 27.REMOVE OIL FILLER STUD BOLT

a.
A363584

Remove the 2 oil filler stud bolts from the cylinder head cover sub-assembly LH.


Hide 11193 28.REMOVE SPARK PLUG TUBE GASKET

a.
A362093

Remove the 6 spark plug tube gaskets.

HINT:

Be careful not to damage the gasket when removing it as the removed gasket needs to be used when installing a new one.



Hide 12101A 29.REMOVE OIL PAN DRAIN PLUG

a.

Remove the oil pan drain plug and gasket.


Hide 12102A 30.REMOVE NO. 2 OIL PAN SUB-ASSEMBLY

Hide 15104 31.REMOVE OIL STRAINER SUB-ASSEMBLY

Hide 89491 32.REMOVE ENGINE OIL LEVEL SENSOR

Hide 15367 33.REMOVE OIL LEVEL SENSOR BRACKET

Hide 12101 34.REMOVE OIL PAN SUB-ASSEMBLY

Hide 12121 35.REMOVE NO. 1 OIL PAN BAFFLE PLATE

a.
A362087

Remove the 8 bolts and No. 1 oil pan baffle plate.


Hide 11381 36.REMOVE REAR ENGINE OIL SEAL RETAINER

a.
A362042

Remove the 6 bolts.


b.
A362043C03
0,0 0,0 false
V100135

Pry


Using a screwdriver, pry out the rear engine oil seal retainer.

NOTICE:

Be careful not to damage the rear engine oil seal retainer.


HINT:

Tape the screwdriver tip before use.



Hide 11381A 37.REMOVE REAR CRANKSHAFT OIL SEAL

a.
A362044C05
0.371,1.743 0.715,1.961 0.343,0.218 10 *a 0.898,1.673 0.599,1.859 false 0.599,1.859 1.589,1.988 false 1.414,1.26 0.633,0.871 false 0.41,0.776 0.684,1.036 0.274,0.260 10 *b
*a Wooden Block
*b Protective Tape


Place the rear engine oil seal retainer on wooden blocks.

NOTICE:

Be careful not to damage the rear engine oil seal retainer.



b.

Using a screwdriver and a hammer, tap out the rear crankshaft oil seal.

HINT:

Tape the screwdriver tip before use.



Hide 11310 38.REMOVE TIMING CHAIN COVER ASSEMBLY

Hide 16100 39.REMOVE ENGINE WATER PUMP ASSEMBLY

Hide 11301C 40.REMOVE FRONT CRANKSHAFT OIL SEAL

Hide 41.SET NO. 1 CYLINDER TO TDC/COMPRESSION

a.

Temporarily install the crankshaft pulley set bolt.


b.
A362045C14
1.771,2.219 2.292,1.667 2.292,1.667 2.844,1.667 true 0.99,0.917 1.24,0.729 1.24,0.729 2.396,0.729 true 1.531,1.708 2.156,0.74 false 2.49,0.625 2.729,0.823 0.24,0.198 10 true *a 2.885,1.573 3.156,1.792 0.271,0.219 10 true *1
*1 Crankshaft Pulley Set Key
*a Center Mark


Set the crankshaft pulley set key to the RH block bore center mark (TDC/compression).


c.
A362046C07
1.396,0.698 1.865,1.177 false 1.438,0.406 1.865,1.177 false 2.448,0.427 1.865,1.177 false 2.521,0.875 1.865,1.177 false 1.292,3.802 1.823,4.156 false 1.365,3.333 1.823,4.156 false 2.333,3.302 1.823,4.156 false 2.375,3.625 1.823,4.156 false 1.781,1.198 2.031,1.458 0.25,0.26 10 true *a 1.74,4.167 2,4.427 0.26,0.26 10 true *a
*a Timing Mark


Check that the timing marks of the camshaft timing gears are aligned with the timing marks of the camshaft bearing cap as shown in the illustration.

If not, turn the crankshaft 1 revolution (360°) and align the timing marks as described above.


Hide 13540 42.REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY

a.
A124589C27
1.146,1.188 1.448,1.76 1.448,1.76 2.635,1.177 false 2.667,1.729 3.021,1.729 false 1.146,0.875 0.729,0.167 0.729,0.167 0.635,0.167 true 2.823,0.854 2.479,0.135 2.479,0.135 2.344,0.135 false 0.427,0.094 0.594,0.271 0.167,0.177 10 true *1 1.375,1.792 1.677,2.01 0.302,0.219 10 true *2 3.052,1.635 3.229,1.813 0.177,0.177 10 true *3 2.125,0.073 2.292,0.25 0.167,0.177 10 true *1
*1 Plunger
*2 Stopper Plate
*3 Pin


Move the stopper plate upward to release the lock, and push the plunger deep into the tensioner.


b.

Move the stopper plate downward to set the lock, and insert a pin of 1.27 mm (0.0500 in.) diameter into the hole of the stopper plate.


c.
A362047

Remove the 2 bolts and No. 1 chain tensioner assembly.


Hide 13559 43.REMOVE CHAIN TENSIONER SLIPPER

a.

Remove the chain tensioner slipper.


Hide 13506 44.REMOVE CHAIN SUB-ASSEMBLY

a.
A362048C07
2.094,0.75 1.969,0.75 1.969,0.75 1.969,1.042 true 2.26,0.615 2.417,0.51 2.417,0.51 2.531,0.51 true 1.885,1.042 2.115,1.271 0.229,0.229 10 true *a 2.573,0.417 2.854,0.677 0.281,0.26 10 true *b 0.615,0.917 0.958,1.177 0.344,0.26 10 false 10°
*a Timing Mark
*b Center Line


Turn the crankshaft counterclockwise 10° to loosen the chain of the crankshaft timing gear or sprocket.


b.

Remove the crankshaft pulley set bolt.


c.
A362049

Remove the chain sub-assembly from the crankshaft timing gear or sprocket and place it on the crankshaft.


d.
A362050C05
0.118,0 0.440,0.253 0.323,0.253 10 *A
*A for Bank 1


Turn the camshaft timing gear assembly on bank 1 clockwise (approximately 60°) and set it as shown in the illustration. Be sure to loosen the chain sub-assembly between the banks.


e.

Remove the chain sub-assembly.


Hide 13530 45.REMOVE IDLE SPROCKET ASSEMBLY

a.
A362051

Using a 10 mm hexagon wrench, remove the No. 2 idle gear shaft, idle sprocket assembly and No. 1 idle gear shaft.


Hide 13561 46.REMOVE NO. 1 CHAIN VIBRATION DAMPER

a.
A362052

Remove the 2 bolts and No. 1 chain vibration damper.


Hide 13562 47.REMOVE NO. 2 CHAIN VIBRATION DAMPER

a.
A362053

Remove the 2 No. 2 chain vibration dampers.


Hide 13521 48.REMOVE CRANKSHAFT TIMING GEAR OR SPROCKET

a.
A362066

Remove the crankshaft timing gear or sprocket from the crankshaft.


b.

Remove the 2 crankshaft timing gear keys from the crankshaft.


Hide 49.REMOVE CAMSHAFT TIMING GEARS AND NO. 2 CHAIN (for Bank 1)

Hide 13550 50.REMOVE NO. 2 CHAIN TENSIONER ASSEMBLY

Hide 51.REMOVE CAMSHAFT BEARING CAP (for Bank 1)

Hide 23476 52.REMOVE FUEL PUMP LIFTER HOUSING

Hide 13511 53.REMOVE CAMSHAFT

Hide 13512 54.REMOVE NO. 2 CAMSHAFT

Hide 11103C 55.REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY RH

Hide 56.REMOVE CAMSHAFT TIMING GEARS AND NO. 2 CHAIN (for Bank 2)

Hide 13560A 57.REMOVE NO. 3 CHAIN TENSIONER ASSEMBLY

Hide 58.REMOVE CAMSHAFT BEARING CAP (for Bank 2)

Hide 13053 59.REMOVE NO. 3 CAMSHAFT SUB-ASSEMBLY

Hide 13054 60.REMOVE NO. 4 CAMSHAFT SUB-ASSEMBLY

Hide 11104A 61.REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY LH

Hide 15678E 62.REMOVE OIL CONTROL VALVE FILTER LH

a.
A362067

Remove the oil control valve filter LH from the camshaft bearing cap.


Hide 15678D 63.REMOVE OIL CONTROL VALVE FILTER RH

a.

Remove the oil control valve filter RH from the camshaft bearing cap.


Hide 11159F 64.REMOVE CAMSHAFT BEARING CAP OIL HOLE GASKET

a.
A362068

Remove the camshaft bearing cap oil hole gasket from the No. 6 camshaft bearing cap.


b.
A362069

Remove the camshaft bearing cap oil hole gasket from the No. 7 camshaft bearing cap.


Hide 13801 65.REMOVE NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY

Hide 13750 66.REMOVE VALVE LASH ADJUSTER ASSEMBLY

Hide 11101 68.REMOVE CYLINDER HEAD SUB-ASSEMBLY

Hide 11115 69.REMOVE CYLINDER HEAD GASKET

Hide 11116 71.REMOVE NO. 2 CYLINDER HEAD GASKET

Hide 82125N 72.REMOVE NO. 5 ENGINE WIRE

a.
A443944

Disconnect the 2 connectors.


b.

Detach the 2 clamps and remove the No. 5 engine wire.


Hide 89615 73.REMOVE KNOCK CONTROL SENSOR

Hide 16332 74.REMOVE NO. 1 WATER OUTLET PIPE

a.
A443945

Remove the 2 bolts and No. 1 water outlet pipe.


Hide 75.REMOVE CYLINDER BLOCK WATER JACKET SPACER

a.
A443946

Remove the 2 cylinder block water jacket spacers from the cylinder block sub-assembly.

NOTICE:

Be sure to remove the water jacket spacers. If not, they may fall and become damaged when the cylinder block sub-assembly is inverted.



Hide 11114A 76.REMOVE STRAIGHT PIN

NOTICE:

It is not necessary to remove a straight pin unless it is being replaced.


Hide 11151 77.REMOVE RING PIN

NOTICE:

It is not necessary to remove a ring pin unless it is being replaced.