Home › Engine / Hybrid System › 7GR-FKS (ENGINE CONTROL) › CAMSHAFT POSITION SENSOR
RM35X0E _51 Engine / Hybrid System _078720 7GR-FKS ENGINE CONTROL _0381921 CAMSHAFT POSITION SENSOR A

7GR-FKS ENGINE CONTROL  CAMSHAFT POSITION SENSOR  INSTALLATION  


PROCEDURE

Hide 11401M 1.INSTALL VVT SENSOR (for Exhaust Side of Bank 2)

a.
A443215

w/o Secondary Air Injection System:

i.

Apply a light coat of engine oil to the O-ring of the VVT sensor.

NOTICE:

If reusing the VVT sensor, be sure to inspect the O-ring.



ii.

Install the VVT sensor to the cylinder head cover sub-assembly LH with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

NOTICE:
·

If the VVT sensor has been struck or dropped, replace it.

·

Make sure that the O-ring is not cracked or moved out of place when installing the VVT sensor.




iii.

Connect the VVT sensor connector.



b.
A443220

w/ Secondary Air Injection System:

i.

Apply a light coat of engine oil to the O-ring of the VVT sensor.

NOTICE:

If reusing the VVT sensor, be sure to inspect the O-ring.



ii.

Install the VVT sensor to the cylinder head cover sub-assembly LH with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

NOTICE:
·

If the VVT sensor has been struck or dropped, replace it.

·

Make sure that the O-ring is not cracked or moved out of place when installing the VVT sensor.




iii.

Connect the VVT sensor connector.



Hide 11401M 2.INSTALL VVT SENSOR (for Intake Side of Bank 2)

a.
A443214

w/o Secondary Air Injection System:

i.

Apply a light coat of engine oil to the O-ring of the VVT sensor.

NOTICE:

If reusing the VVT sensor, be sure to inspect the O-ring.



ii.

Install the VVT sensor to the cylinder head cover sub-assembly LH with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

NOTICE:
·

If the VVT sensor has been struck or dropped, replace it.

·

Make sure that the O-ring is not cracked or moved out of place when installing the VVT sensor.




iii.

Connect the VVT sensor connector.



b.
A443219

w/ Secondary Air Injection System:

i.

Apply a light coat of engine oil to the O-ring of the VVT sensor.

NOTICE:

If reusing the VVT sensor, be sure to inspect the O-ring.



ii.

Install the VVT sensor to the cylinder head cover sub-assembly LH with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

NOTICE:
·

If the VVT sensor has been struck or dropped, replace it.

·

Make sure that the O-ring is not cracked or moved out of place when installing the VVT sensor.




iii.

Connect the VVT sensor connector.



Hide 11401M 3.INSTALL VVT SENSOR (for Exhaust Side of Bank 1)

a.
A443213

w/o Secondary Air Injection System:

i.

Apply a light coat of engine oil to the O-ring of the VVT sensor.

NOTICE:

If reusing the VVT sensor, be sure to inspect the O-ring.



ii.

Install the VVT sensor to the cylinder head cover sub-assembly with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

NOTICE:
·

If the VVT sensor has been struck or dropped, replace it.

·

Make sure that the O-ring is not cracked or moved out of place when installing the VVT sensor.




iii.

Connect the VVT sensor connector.



b.
A443218

w/ Secondary Air Injection System:

i.

Apply a light coat of engine oil to the O-ring of the VVT sensor.

NOTICE:

If reusing the VVT sensor, be sure to inspect the O-ring.



ii.

Install the VVT sensor to the cylinder head cover sub-assembly with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

NOTICE:
·

If the VVT sensor has been struck or dropped, replace it.

·

Make sure that the O-ring is not cracked or moved out of place when installing the VVT sensor.




iii.

Connect the VVT sensor connector.



Hide 11401Q 4.INSTALL VVT SENSOR (for Intake Side of Bank 1)

a.
A443212

w/o Secondary Air Injection System:

i.

Apply a light coat of engine oil to the O-ring of the VVT sensor.

NOTICE:

If reusing the VVT sensor, be sure to inspect the O-ring.



ii.

Install the VVT sensor to the cylinder head cover sub-assembly with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

NOTICE:
·

If the VVT sensor has been struck or dropped, replace it.

·

Make sure that the O-ring is not cracked or moved out of place when installing the VVT sensor.




iii.

Connect the VVT sensor connector.



b.
A443217

w/ Secondary Air Injection System:

i.

Apply a light coat of engine oil to the O-ring of the VVT sensor.

NOTICE:

If reusing the VVT sensor, be sure to inspect the O-ring.



ii.

Install the VVT sensor to the cylinder head cover sub-assembly with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

NOTICE:
·

If the VVT sensor has been struck or dropped, replace it.

·

Make sure that the O-ring is not cracked or moved out of place when installing the VVT sensor.




iii.

Connect the VVT sensor connector.



Hide 5.INSTALL AIR SWITCHING VALVE ASSEMBLY (w/ Secondary Air Injection System)

Hide 17190 6.INSTALL INTAKE AIR SURGE TANK ASSEMBLY

Hide 7.INSPECT FOR ENGINE OIL LEAK