Home › Drivetrain › RC60J (MANUAL TRANSMISSION / TRANSAXLE) › MANUAL TRANSMISSION UNIT
RM35X0E _52 Drivetrain _078740 RC60J MANUAL TRANSMISSION / TRANSAXLE _0382063 MANUAL TRANSMISSION UNIT A

RC60J MANUAL TRANSMISSION / TRANSAXLE  MANUAL TRANSMISSION UNIT  DISASSEMBLY  


PROCEDURE

Hide 31126 1.REMOVE CLUTCH RELEASE FORK BOOT (for 1GD-FTV)

Hide 31230 2.REMOVE CLUTCH RELEASE BEARING ASSEMBLY

Hide 31236B 3.REMOVE RELEASE FORK SUPPORT

Hide 84210 4.REMOVE BACK-UP LIGHT SWITCH ASSEMBLY

Hide 5.REMOVE BACK-UP LIGHT SWITCH BRACKET

a.
C405235

Remove the 3 bolts and 2 back-up light switch brackets.


Hide 6.REMOVE BREATHER PLUG SUB-ASSEMBLY

HINT:

Perform this procedure only when replacement of the breather plug sub-assembly is necessary.


a.

Remove the breather plug sub-assembly from the extension housing sub-assembly.


Hide 89413B 7.REMOVE TRANSMISSION REVOLUTION SENSOR (w/ Sensor)

Hide 84545 8.REMOVE NEUTRAL POSITION SWITCH (w/ Stop And Start System)

Hide 33101A 9.REMOVE MANUAL TRANSMISSION FILLER PLUG

a.
C412069C01
0,0 0.313,0.156 0.313,0.156 10 false *A 0,2.365 0.313,2.521 0.313,0.156 10 false *B
*A for 1GD-FTV
*B for 7GR-FKS


Remove the manual transmission filler plug and gasket from the manual transmission case sub-assembly.


Hide 33104 10.REMOVE DRAIN PLUG SUB-ASSEMBLY

a.
C412070C01
0,0 0.313,0.156 0.313,0.156 10 false *A 0,2.365 0.313,2.521 0.313,0.156 10 false *B
*A for 1GD-FTV
*B for 7GR-FKS


Remove the drain plug sub-assembly and gasket from the manual transmission case sub-assembly.


Hide 33275B 11.REMOVE SHAFT DETENT BALL

a.
C405238

Using a 6 mm hexagon socket wrench, remove the 4 shift detent ball plugs from the rear transmission case.


b.

Remove the 4 shift detent ball low side compression springs and 4 shaft detent balls from the rear transmission case.


Hide 33292A 12.REMOVE LOCK BALL PIN

a.
C405240C01
0,2.333 3.417,2.333 false 0,0.031 0.313,0.188 0.313,0.156 10 false *A 0.021,2.375 0.333,2.531 0.313,0.156 10 false *B
*A for 1GD-FTV
*B for 7GR-FKS


Using a 10 mm hexagon socket wrench, remove the No. 2 with head straight screw plug from the rear transmission case.


b.

Remove the compression spring and the lock ball pin from the rear transmission case.


Hide 33253B 13.REMOVE OUTER SHIFT LEVER

a.
C407573

Remove the nut and spring washer from the outer shift lever.


b.
C407575

Using a brass bar and hammer, remove the No. 2 lever lock pin and outer shift lever from the shift lever with seal housing sub-assembly.


Hide 33207 14.REMOVE SHIFT LEVER WITH SEAL HOUSING SUB-ASSEMBLY

a.
C407574

Remove the 6 bolts and shift lever with seal housing sub-assembly from the extension housing sub-assembly.


Hide 33267A 15.REMOVE SHIFT GATE PLATE

a.
C412081

Remove the 2 bolts and shift gate plate from the shift lever with seal housing sub-assembly.


Hide 33292A 16.REMOVE LOCK BALL PIN

a.
C412082

Remove the compression spring and lock ball pin from the shift lever with seal housing sub-assembly.


Hide 33257 17.REMOVE OUTER SELECT LEVER

a.
C412089

Remove the E-ring.


b.
C412090

Remove the compression spring and pin.


c.
C412075

Using a 5 mm pin punch and hammer, tap out the slotted spring pin.


d.

Remove the inner select lever and outer select lever from the shift lever with seal housing sub-assembly.


Hide 33207B 18.REMOVE SHIFT LEVER SHAFT OIL SEAL

a.
C412083C01
0.667,1.667 0.833,1.667 0.833,1.667 1.771,0.667 true 0.49,1.552 0.802,1.708 0.313,0.156 10 false *a
*a Protective Tape


Using a screwdriver with its tip wrapped with protective tape, remove the shift lever shaft oil seal from the shift lever with seal housing sub-assembly.

HINT:

Tape the screwdriver tip before use.



Hide 33207A 19.REMOVE CONTROL SHAFT OIL SEAL

a.
C412094C01
1.167,1.833 1.375,1.833 1.375,1.833 2.104,0.885 true 0.979,1.729 1.292,1.885 0.313,0.156 10 false *a
*a Protective Tape


Using a screwdriver with its tip wrapped with protective tape, remove the control shaft oil seal from the shift lever with seal housing sub-assembly.

HINT:

Tape the screwdriver tip before use.



Hide 33103 20.REMOVE EXTENSION HOUSING SUB-ASSEMBLY

a.
C412091

Using a 6 mm hexagon socket wrench, remove the 2 hexagon bolts.


b.

Remove the E-ring.


c.
C407577

Using a 5 mm pin punch and hammer, remove the slotted spring pin from the select lever shaft head and shift and select lever shaft.


d.
C407578

Remove the 8 bolts, shift lever shaft, shift and select lever shaft head and extension housing sub-assembly.


Hide 33124M 21.REMOVE NO. 4 OIL RECEIVER PIPE (MTM)

a.
C405242

Remove the No. 4 oil receiver pipe (MTM) from the extension housing sub-assembly.


Hide 33103R 22.REMOVE MANUAL TRANSMISSION EXTENSION HOUSING OIL SEAL

Hide 33176B 23.REMOVE TRANSMISSION OIL SEPARATOR

a.
C412079

Remove the 2 bolts and transmission oil separator from the rear transmission case.


Hide 33127 24.REMOVE TRANSMISSION OIL RUNNER

a.
C412080

Using a snap ring expander, remove the snap ring from the output shaft sub-assembly.


b.

Remove the transmission oil runner from the output shaft sub-assembly.


Hide 33321G 25.UNSTAKE MANUAL TRANSMISSION OUTPUT SHAFT REAR SET NUT

a.
C323790

Using a chisel and hammer, unstake the caulking of the rear lock nut from the output shaft.

SST
09326-35020  


Hide 33321G 26.REMOVE MANUAL TRANSMISSION OUTPUT SHAFT REAR SET NUT

a.

Engage the gear, and then secure the input shaft using SST.

C405243C02
3.5,3.802 3.5,0 false 4.167,1.25 4.25,1.25 4.25,1.25 4.417,1.75 false 0.417,1.25 0.5,1.25 0.5,1.25 0.667,1.75 false 1.979,0.719 2.167,0.917 2.167,0.917 2.25,0.917 false 5.792,0.719 5.979,0.917 5.979,0.917 6.063,0.917 false 1.552,1.917 2.448,2.583 2.448,2.583 2.531,2.583 true 5.344,1.969 6.24,2.635 6.24,2.635 6.323,2.635 true 4.302,3.042 4.385,3.042 4.385,3.042 4.5,3.146 false 0.438,3.031 0.521,3.031 0.521,3.031 0.635,3.135 false 2.292,0.479 2.417,0.26 2.417,0.26 2.5,0.26 false 6.167,0.479 6.271,0.292 6.271,0.292 6.354,0.292 false 0.042,0.031 0.354,0.188 0.313,0.156 10 false *A 3.563,0.063 3.875,0.219 0.313,0.156 10 false *B 3.854,1.146 4.313,1.344 0.458,0.198 10 false SST 0.125,1.146 0.583,1.344 0.458,0.198 10 false SST 2.281,0.823 2.438,1.021 0.156,0.198 10 false A 6.104,0.823 6.26,1.021 0.156,0.198 10 false A 2.604,2.479 2.76,2.677 0.156,0.198 10 false A 6.375,2.531 6.531,2.729 0.156,0.198 10 false A 3.969,2.948 4.313,3.167 0.344,0.219 10 true SST 0.073,2.948 0.385,3.146 0.313,0.198 10 true SST 2.531,0.177 2.844,0.375 0.313,0.198 10 false *1 6.385,0.198 6.698,0.396 0.313,0.198 10 false *1
*A for 1GD-FTV *B for 7GR-FKS
*1 Input Shaft - -


SST
09322-35010  (09322-03010, 09322-03020, 09322-03030, 90105-12087, 90170-12030, 94622-51200)

HINT:
·

Install SST securely so that the part labeled A is in-line with the input shaft.

·

Make sure that the part labeled A moves back and forth by hand after installing SST.




b.
C323513N01
2.281,1.104 2.844,1.104 true 2.917,1.031 3.375,1.229 0.458,0.198 10 false SST

Using SST, remove the manual transmission output shaft rear set nut from the output shaft.

SST
09326-35020  


Hide 31111 27.REMOVE CLUTCH HOUSING

a.
C405245C01
0,2.417 3.427,2.417 false 0.052,0.063 0.365,0.219 0.313,0.156 10 false *A 0.073,2.49 0.385,2.646 0.313,0.156 10 false *B
*A for 1GD-FTV
*B for 7GR-FKS


Remove the 10 bolts.


b.

Using a plastic-faced hammer, carefully tap off the clutch housing to remove it.


Hide 33131D 28.REMOVE FRONT BEARING RETAINER

a.
C405247C01
0,2.417 3.427,2.417 false 0.063,0.052 0.375,0.208 0.313,0.156 10 false *A 0.042,2.469 0.354,2.625 0.313,0.156 10 false *B
*A for 1GD-FTV
*B for 7GR-FKS


Remove the 11 bolts.


b.

Using a screwdriver wrapped in protective tape, remove the front bearing retainer by prying the points in the illustration.

C405249C01
3.583,2.792 3.583,0 false 0.031,0.031 0.344,0.188 0.313,0.156 10 false *A 3.625,0.042 3.938,0.198 0.313,0.156 10 false *B
*A for 1GD-FTV *B for 7GR-FKS


NOTICE:
·

Do not damage the sealing surface of the clutch housing and manual transmission case sub-assembly.

·

Do not damage the sealing surface of the front bearing retainer and manual transmission case sub-assembly.




Hide 33124C 29.REMOVE NO. 1 OIL RECEIVER PIPE (MTM)

a.

Remove the No. 1 oil receiver pipe (MTM) from the front bearing retainer.


Hide 33131A 30.REMOVE FRONT TRANSMISSION BEARING RETAINER OIL SEAL

Hide 33411E 31.REMOVE COUNTER GEAR SHAFT NUT

a.
C323798

Using a chisel and hammer, unstake the counter gear shaft nut.


b.
C334261N01
2.365,3.333 1.917,2.583 1.917,2.583 1.75,2.583 false 1.438,2.5 1.896,2.698 0.458,0.198 10 false SST

Using SST, hold the output shaft.

SST
09326-35020  


c.

Using a 41 mm socket wrench, remove the counter gear shaft nut.


Hide 33311T 32.REMOVE INPUT SHAFT SHAFT SNAP RING

a.
C323800

Using snap ring pliers, remove the input shaft shaft snap ring.


Hide 33311G 33.REMOVE FRONT BEARING SHAFT SNAP RING

a.
C323801

Using a snap ring expander, remove the front bearing shaft snap ring.


Hide 33451H 34.REMOVE REVERSE IDLER GEAR SHAFT BOLT

a.
C405251

Remove the reverse idler gear shaft bolt and gasket from the reverse idler gear shaft.


Hide 33101 35.REMOVE MANUAL TRANSMISSION CASE SUB-ASSEMBLY

CAUTION:

Since the manual transmission unit is very heavy, 2 people are needed to remove the manual transmission case sub-assembly.


a.
C323804

Remove the 12 bolts.


b.
C334030

In order to prevent the reverse idler gear from falling when removing the transmission case, set the manual transmission assembly on its side so that the installation hole of the reverse idler gear stopper bolt is facing upward as shown in the illustration.


c.
C334732C01
1.615,0.885 1.948,0.344 1.948,0.344 2.104,0.344 true 2.146,4.281 2.333,4.49 0.188,0.208 10 false *1 2.135,0.25 2.344,0.448 0.208,0.198 10 false *a 0.479,2.458 0.698,2.635 0.219,0.177 10 false *1
*1 Straight Pin
*a Protective Tape


Using a screwdriver wrapped in protective tape, separate the transmission case sub-assembly and transmission intermediate plate by prying at the points shown in the illustration.

NOTICE:

Do not damage the sealing surfaces of the manual transmission case sub-assembly and transmission intermediate plate.



d.
C334782

Place wooden blocks or other objects underneath the rear transmission case to securely support it as shown in the illustration.


e.

Remove the manual transmission case sub-assembly from the rear transmission case.


Hide 33461 36.REMOVE REVERSE IDLER GEAR

CAUTION:

Since the manual transmission is very heavy, perform these procedures with 2 people. While one person is removing the reverse idler gear, have the other person hold the manual transmission in place.


NOTICE:

There are types with a reverse idler gear shaft spacer and types without a reverse idler gear shaft spacer.


a.
C323805

Remove the reverse idler gear and No. 2 oil receiver pipe (MTM) from the transmission unit.


b.

Remove the No. 2 oil receiver pipe (MTM) from the reverse idler gear shaft.


c.
C419304

w/ Reverse Idler Gear Shaft Spacer:

i.

Remove the reverse idler gear bearing, reverse idler gear shaft spacer and reverse idler gear from the reverse idler gear shaft.



d.
C323806

w/o Reverse Idler Gear Shaft Spacer:

i.

Remove the reverse idler gear bearing and reverse idler gear from the reverse idler gear shaft.



Hide 33261C 37.REMOVE SHIFT AND SELECT LEVER SHAFT

a.
C405252

Remove the shift and select lever shaft from the rear transmission case.

CAUTION:

Since the manual transmission is very heavy, perform these procedures with 2 people. While one person is removing the shift and select lever shaft, have the other person hold the manual transmission in place.



Hide 33268C 38.REMOVE SHIFT INTERLOCK PLATE STOPPER

a.
C336101

Remove the 2 bolts and shift interlock plate stopper from the transmission unit.

CAUTION:

Since the manual transmission is very heavy, perform these procedures with 2 people. While one person is removing the shift interlock plate stopper, have the other person hold the manual transmission in place.



Hide 33109C 39.REMOVE MANUAL TRANSMISSION OIL SEPARATOR SUB-ASSEMBLY

a.
C412077

Remove the 2 bolts and manual transmission oil separator sub-assembly (front side).

CAUTION:

Since the manual transmission is very heavy, perform these procedures with 2 people. While one person is removing the manual transmission oil separator sub-assembly, have the other person hold the manual transmission in place.



Hide 33449B 40.REMOVE TRANSMISSION MAGNET

a.
C333991

Remove the transmission magnet from the transmission intermediate plate.

CAUTION:

Since the manual transmission is very heavy, perform these procedures with 2 people. While one person is removing the transmission magnet, have the other person hold the manual transmission in place.



Hide 33112G 41.REMOVE REAR TRANSMISSION CASE

a.
C334019N01
1.365,2.958 1.729,3.208 1.729,3.208 2,3.208 false 2.104,3.125 2.469,3.281 0.365,0.156 10 false SST

Using SST, set the transmission unit.

SST
09310-71011  

CAUTION:

Since the manual transmission unit is very heavy, 2 people are needed to set the transmission unit.



b.
C323824N01
1.406,3.01 2.146,2.76 false 1.115,2.948 1.573,3.146 0.458,0.198 10 false SST

Stand the manual transmission upright as shown in the illustration.

CAUTION:

Since the manual transmission unit is very heavy, 2 people are needed to stand the manual transmission upright as shown in the illustration.



c.
C324014

Remove the rear output shaft bearing.


d.
C323825

Remove the rear transmission case and transmission intermediate plate.


e.

Remove the transmission intermediate plate from the rear transmission case.


f.
C333737

Remove the manual transmission oil separator sub-assembly (rear side).


Hide 33124L 42.REMOVE NO. 3 OIL RECEIVER PIPE (MTM)

a.
C336102

Remove the No. 3 oil receiver pipe (MTM) from the rear transmission case.


Hide 43.REMOVE GEAR SHIFT FORK AND GEAR SHIFT FORK SHAFT ASSEMBLY

a.
C333992C02
0,0 0,0 false
V113147

Remove in this direction


Move the No. 2 hub sleeve as shown in the illustration and remove the No. 3 gear shift fork from SST as shown in the illustration.


b.
C333994C03
0.76,1.604 0.958,1.979 0.958,1.979 1.219,1.979 true 1.313,1.615 1.51,1.99 1.51,1.99 1.771,1.99 true 1.292,1.906 1.448,2.104 0.156,0.198 10 true 1 1.865,1.896 2.021,2.094 0.156,0.198 10 true 2
V113147

Remove in this direction


Slide the No. 3 gear shift fork from position 1 to 2 and then remove the No. 3 gear shift fork together with the No. 3 gear shift fork shaft.


c.
C333996C02
1.833,0.365 2.042,0.365 2.042,0.365 2.271,0.823 true 0.458,1.271 0.167,2 0.167,2 0.417,2 true 2.104,3.479 2.583,3.417 2.583,3.417 2.75,3.417 false 1.615,0.271 1.927,0.469 0.313,0.198 10 false *1 0.5,1.927 0.813,2.125 0.313,0.198 10 false *2 2.771,3.333 3.083,3.531 0.313,0.198 10 false *3
*1 No. 2 Transmission Hub Sleeve
*2 No. 1 Transmission Hub Sleeve
*3 No. 4 Gear Shift Fork Shaft
V113147

Remove in this direction


Slide the No. 2 and No. 1 transmission hub sleeves as shown in the illustration.


d.

Remove the bolt from the No. 4 gear shift fork, and then slide the No. 4 gear shift fork shaft as shown in the illustration.


e.
C333997C02
0,0 0,0 false
V113147

Remove in this direction


Move the gear shift fork and gear shift fork shaft assembly as shown in the illustration.

NOTICE:

Move the 3 shift fork shafts together.



f.
C333998

Remove the gear shift fork and gear shift fork shaft assembly from the counter gear.

NOTICE:

Do not drop the No. 4 gear shift fork.



g.
C336103

Remove the No. 4 gear shift fork.


Hide 33321 44.REMOVE OUTPUT SHAFT SUB-ASSEMBLY

a.
C336108C01
2.021,0.677 2.26,0.469 2.26,0.469 2.521,0.469 false 0.729,0.563 0.979,0.563 0.979,0.563 1.208,0.656 false 0.521,0.51 0.833,0.667 0.313,0.156 10 false *1 2.563,0.396 2.875,0.552 0.313,0.156 10 false *2
*1 Input Shaft
*2 Counter Gear


Expand SST to the left and right.


b.
C336125

Remove the output shaft from the input shaft.


c.

Remove the output shaft spacer and rear output shaft bearing shim.


Hide 33311D 45.REMOVE INPUT SHAFT BEARING

a.
C336106

Remove the input shaft bearing from the input shaft.


Hide 33369B 46.REMOVE NO. 4 SYNCHRONIZER RING

a.
C336107

Remove the No. 4 synchronizer ring from the input shaft.


Hide 33311 47.REMOVE INPUT SHAFT

a.

Remove the input shaft from SST.


Hide 33421 48.REMOVE COUNTER GEAR

a.

Remove the counter gear from SST.


Hide 33411H 49.REMOVE REAR COUNTER GEAR BEARING OR ROLLER

a.
C323842

Remove the bolt and bearing lock plate.


b.
C323843C01
0.708,3.167 1.406,2.917 true 1.563,0.667 0.417,0.396 0.417,0.396 0.865,0.688 true 0.375,3.115 0.833,3.313 0.458,0.198 10 false SST 0.198,0.281 0.51,0.479 0.313,0.198 10 false *a
*a Groove of the Rear Transmission Case


Using SST, remove the rear counter gear bearing or roller (outer) from the rear transmission case.

SST
09308-00010  

NOTICE:

Do not damage the contact surfaces of the rear transmission case.


HINT:

Align the groove of the rear transmission case with the claws of SST.



Hide 33321A 50.REMOVE REAR OUTPUT SHAFT BEARING (OUTER RACE)

a.
C323845C01
3.135,0.698 1.521,0.292 1.521,0.292 2.448,0.708 true 1.917,3.104 2.49,2.74 false 1.302,0.167 1.615,0.365 0.313,0.198 10 false *a 1.594,3.052 2.052,3.25 0.458,0.198 10 false SST
*a Groove of the Rear Transmission Case


Using SST, remove the rear output shaft bearing (outer race) from the rear transmission case.

SST
09308-00010  

NOTICE:

Do not damage the contact surfaces of the rear transmission case.


HINT:

Align the groove of the rear transmission case with the claws of SST.



Hide 33261K 51.REMOVE SHIFT AND SELECT LEVER SHAFT NEEDLE ROLLER BEARING

a.
C412097C03
2.604,0.385 2.771,0.385 false 2.802,0.302 3.26,0.5 0.458,0.198 10 false SST
V113147

Remove in this Direction


Using SST, remove the shift and select lever shaft needle roller bearing (rear side) from the extension housing sub-assembly.

SST
09319-60020  


Hide 33321N 52.REMOVE FRONT OUTPUT SHAFT BEARING (OUTER RACE)

a.
C323844C01
0.823,0.667 0.448,0.302 0.448,0.302 1.625,0.667 true 0.542,2.865 0.698,3.135 false 0.25,0.188 0.563,0.344 0.313,0.156 10 false *a 0.75,3.156 1.208,3.354 0.458,0.198 10 false SST
*a Groove of the Rear Transmission Case


Using SST, remove the front output shaft bearing (outer race) from the rear transmission case.

SST
09308-00010  

NOTICE:

Do not damage the contact surfaces of the rear transmission case.


HINT:

Align the groove of the rear transmission case with the claws of SST.



Hide 33242L 53.REMOVE SHIFT FORK SHAFT BEARING

a.
C323851C02
2.156,0.448 2.354,0.51 false 0.083,0.49 0.396,0.646 0.313,0.156 10 false *a 1.24,0.396 1.427,0.573 0.188,0.177 10 true *b 1.885,0.375 2.344,0.573 0.458,0.198 10 false SST
*a Turn
*b Hold


Using SST, remove the 2 shift fork shaft bearings (rear side) from the rear transmission case.

SST
09319-60020  


Hide 33261K 54.REMOVE SHIFT AND SELECT LEVER SHAFT NEEDLE ROLLER BEARING

a.
C336109C01
2.76,0.396 2.938,0.396 false 0.229,0.552 0.531,0.75 0.302,0.198 10 true *a 1.26,0.542 1.49,0.75 0.229,0.208 10 true *b 3.021,0.323 3.323,0.552 0.302,0.229 10 true SST
*a Turn
*b Hold


Using SST, remove the shift and select lever shaft needle roller bearing (front side) from the front transmission case.

SST
09319-60020  


Hide 33242L 55.REMOVE SHIFT FORK SHAFT BEARING

a.
C323870C02
2.104,0.333 2.417,0.49 false 1.271,0.729 1.479,0.906 0.208,0.177 10 true *a 0.156,0.531 0.365,0.708 0.208,0.177 10 true *b 1.792,0.281 2.25,0.479 0.458,0.198 10 false SST
*a Turn
*b Hold


Using SST, remove the 2 shift fork shaft bearings (front side) from the front transmission case sub-assembly.

SST
09319-60020  


Hide 33261C 56.REMOVE SHIFT AND SELECT LEVER SHAFT

a.
C405256

Remove the bolt from the inner select lever.


b.
C412073

Using a 5 mm pin punch and hammer, tap out the slotted spring pin.


c.
C412088C01
3.104,0.823 3.26,1.021 0.156,0.198 10 false - 3.125,0.854 3.281,1.052 0.156,0.198 10 false -
V113147

Remove in this Direction


Remove the shift and select lever shaft from the shift interlock plate sub-assembly and inner select lever.


Hide 33243A 57.REMOVE NO. 2 GEAR SHIFT FORK SHAFT

a.
C336111

Remove the bolt and No. 2 gear shift fork from the No. 2 gear shift fork shaft.


b.

Remove the No. 2 gear shift fork shaft from the No. 1 gear shift fork head.


c.
C336973

Place a cloth on 2 V-blocks, set the No. 2 gear shift fork shaft on the cloth, and then hold the No. 2 gear shift fork shaft in place as shown in the illustration.

CAUTION:
·

Perform this procedure with 2 people.

·

Make sure to protect the No. 2 gear shift fork shaft with a cloth before performing this procedure. If the No. 2 gear shift fork shaft is damaged, shifting operations will worsen.

·

Firmly secure the No. 2 gear shift fork shaft.




d.

Using a 5 mm pin punch and hammer, tap out the slotted spring pin.


e.

Remove the No. 2 gear shift head from the No. 2 gear shift fork shaft.


Hide 33245G 58.REMOVE NO. 4 GEAR SHIFT FORK SHAFT

a.
C336969

Place a cloth on 2 V-blocks, set the No. 4 gear shift fork shaft on the cloth, and then hold the No. 4 gear shift fork shaft in place as shown in the illustration.

CAUTION:
·

Perform this procedure with 2 people.

·

Make sure to protect the No. 4 gear shift fork shaft with a cloth before performing this procedure. If the No. 4 gear shift fork shaft is damaged, shifting operations will worsen.

·

Firmly secure the No. 4 gear shift fork shaft.




b.

Using a 5 mm pin punch and hammer, tap out the slotted spring pin.


c.

Remove the No. 4 gear shift head from the No. 4 gear shift fork shaft.


Hide 33242 59.REMOVE NO. 1 GEAR SHIFT FORK SHAFT

a.
C323878

Remove the bolt and No. 1 gear shift fork from the No. 1 gear shift fork shaft.


b.
C336971

Place a cloth on 2 V-blocks, set the No. 1 gear shift fork shaft on the cloth, and then hold the No. 1 gear shift fork shaft in place as shown in the illustration.

CAUTION:
·

Perform this procedure with 2 people.

·

Make sure to protect the No. 1 gear shift fork shaft with a cloth before performing this procedure. If the No. 1 gear shift fork shaft is damaged, shifting operations will worsen.

·

Firmly secure the No. 1 gear shift fork shaft.




c.

Using a 5 mm pin punch and hammer, tap out the slotted spring pin.


d.

Remove the No. 1 gear shift head from the No. 1 gear shift fork shaft.


Hide 33244D 60.REMOVE NO. 3 GEAR SHIFT FORK SHAFT

a.
C323880

Remove the bolt and No. 3 gear shift fork from the No. 3 gear shift fork shaft.


Hide 61.REMOVE STRAIGHT PIN AND RING PIN

NOTICE:

It is not necessary to remove the straight pin and ring pin unless it is being replaced.