Home › Drivetrain › RC60J (MANUAL TRANSMISSION / TRANSAXLE) › TRANSMISSION CASE OIL SEAL › 2019.02–2019.06
RM35X0E _52 Drivetrain _078740 RC60J MANUAL TRANSMISSION / TRANSAXLE _0382069 TRANSMISSION CASE OIL SEAL A

RC60J MANUAL TRANSMISSION / TRANSAXLE  TRANSMISSION CASE OIL SEAL  REPLACEMENT  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during front transmission bearing retainer oil seal removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Disconnect cable from negative(-) battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
for 7GR-FKS:
·

Gas leaks from exhaust system


Inspection after repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)
w/ Stop and Start System:

Starter assembly

NOTICE:

When the starter assembly is replaced, "STARTER relay" and "STARTER NO.2 relay" must be also replaced.



Clear the number of starter operations Stop and start system (Click here)

CAUTION:
·
A350542

To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.

·
C313282C03
2.573,0.583 2.906,0.583 false 2.948,0.479 3.26,0.677 0.313,0.198 10 false *a
*a Object Exceeding Weight Limit of Transmission Jack


The manual transmission assembly is very heavy. Be sure to follow the procedure described in the repair manual, or the transmission jack may suddenly drop or a part may fall.



HINT:

When the cable is disconnected / reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the systems is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Stop and start system Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes). (Click here)
Lane control system Drive the vehicle straight ahead at 15 km/h (10 mph) or more for 1 second or more. (Click here)
Pre-collision system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power slide door system Fully close the slide door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the slide door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 31126 2.REMOVE CLUTCH RELEASE FORK BOOT (for 1GD-FTV)

Hide 31230 3.REMOVE CLUTCH RELEASE BEARING ASSEMBLY

Hide 31236B 4.REMOVE RELEASE FORK SUPPORT

Hide 33124C 7.REMOVE NO. 1 OIL RECEIVER PIPE (MTM)

Hide 33131A 8.REMOVE FRONT TRANSMISSION BEARING RETAINER OIL SEAL

a.
C405673C01
0.74,0.24 1.01,0.24 1.01,0.24 1.729,0.646 true 0.521,0.146 0.75,0.375 0.229,0.229 10 false *a
*a Protective Tape


Using a screwdriver, pry out the front transmission bearing retainer oil seal.

NOTICE:

Be careful not to damage the front bearing retainer.


HINT:

Tape the screwdriver tip before use.



Hide 33131A 9.INSTALL FRONT TRANSMISSION BEARING RETAINER OIL SEAL

a.
C405674N01
1.719,2.125 0.573,2.083 0.573,2.083 1.833,1.781 true 0.25,2.01 0.583,2.24 0.333,0.229 10 false SST

Using SST and a press, press in a new front transmission bearing retainer oil seal.

SST
09950-60011  (09951-00470)
09950-70010  (09951-07150)

Standard Drive in Depth:

0.8 to 1.8 mm (0.0315 to 0.0708 in.)


NOTICE:

Be careful not to damage the lip of the front transmission bearing retainer oil seal.



b.

Apply MP grease oil to the lip of the front transmission bearing retainer oil seal.


Hide 33124C 10.INSTALL NO. 1 OIL RECEIVER PIPE (MTM)

Hide 31236B 13.INSTALL RELEASE FORK SUPPORT

Hide 31230 14.INSTALL CLUTCH RELEASE BEARING ASSEMBLY

Hide 31126 15.INSTALL CLUTCH RELEASE FORK BOOT (for 1GD-FTV)