Home › Drivetrain › CLUTCH › CLUTCH UNIT
RM35X0E _52 Drivetrain _078837 CLUTCH _0382379 CLUTCH UNIT A

CLUTCH  CLUTCH UNIT  INSTALLATION  


PROCEDURE

Hide 31241 1.INSTALL CLUTCH RELEASE FORK DUST SEAL

a.

Install the clutch release fork dust seal to the clutch release fork sub-assembly.


b.

Install the clutch release fork collar to the clutch release fork sub-assembly.


Hide 31250 2.INSTALL CLUTCH DISC ASSEMBLY

a.

Insert SST into the clutch disc assembly, and then attach them both to the flywheel.

SST
09301-00320  

NOTICE:

Insert the clutch disc assembly in the correct direction.


C410752C01
2.458,1.708 2.292,1.708 2.292,1.708 2.125,1.219 true 6.031,1.729 5.865,1.729 5.865,1.729 5.698,1.24 true 1.781,2.24 2.24,2.24 true 5.333,2.219 5.792,2.219 true 2.521,1.646 2.979,1.844 0.458,0.198 10 false SST 6.094,1.635 6.552,1.833 0.458,0.198 10 false SST 1.26,2.188 1.573,2.385 0.313,0.198 10 false *a 4.719,2.198 5.031,2.396 0.313,0.198 10 false *a 2.302,2.167 2.625,2.365 0.323,0.198 10 false *1 5.875,2.135 6.188,2.333 0.313,0.198 10 false *1 0.146,0.167 0.458,0.365 0.313,0.198 10 false *A 3.813,0.177 4.125,0.375 0.313,0.198 10 false *B
*A for 7GR-FKS *B for 1GD-FTV
*1 Clutch Disc Assembly *a Flywheel side



Hide 31210 3.INSTALL CLUTCH COVER ASSEMBLY

C410753C02
1.052,0.885 0.615,0.885 0.615,0.885 1.125,0.938 true 0.948,3.313 0.51,3.313 0.51,3.313 1.021,3.365 true 0.104,0.104 0.417,0.302 0.313,0.198 10 true *A 0.115,2.458 0.427,2.656 0.313,0.198 10 true *B 0.271,0.771 0.583,0.969 0.313,0.198 10 true *a 0.198,3.188 0.51,3.385 0.313,0.198 10 true *a 2.5,0.094 3.208,0.406 0.708,0.313 10 true 1 (*b), 4 0.865,0.125 1.083,0.344 0.219,0.219 10 true 7 0.354,1.229 0.573,1.448 0.219,0.219 10 true 3 0.896,2.167 1.115,2.385 0.219,0.219 10 false 6 2.219,2.219 2.438,2.438 0.219,0.219 10 false 2 2.917,1.042 3.135,1.26 0.219,0.219 10 false 5 2.458,2.469 3.167,2.781 0.708,0.313 10 true 1 (*b), 4 2.833,3.375 3.052,3.594 0.219,0.219 10 false 5 1.813,4.427 2.031,4.646 0.219,0.219 10 false 2 0.75,4.438 0.969,4.656 0.219,0.219 10 false 6 0.302,3.646 0.521,3.865 0.219,0.219 10 true 3 0.813,2.542 1.031,2.76 0.219,0.219 10 true 7
*A for 7GR-FKS
*B for 1GD-FTV
*a Matchmark
*b Temporarily install


a.

Align the matchmarks on the clutch cover assembly with the one on the flywheel.


b.

Following the order shown in the illustration, tighten the 6 bolts, starting with the bolt located near the knock pin at the top.

SST
09301-00320  

Torque:
19.1 N*m (195 kgf*cm, 14 ft.*lbf)

HINT:
·

Following the order in the illustration, tighten the bolts evenly one at a time.

·

Move SST up and down, right and left lightly after checking that the clutch disc assembly is in the center, and tighten the bolts.




Hide 31210 4.INSPECT AND ADJUST CLUTCH COVER ASSEMBLY

a.

Using a dial indicator with a roller instrument, check the diaphragm spring tip alignment.

C410754C01
2.042,2.979 2.531,2.563 true 5.646,3.042 6.333,2.333 true 2.594,2.427 3.052,2.625 0.458,0.198 10 false SST 6.406,2.188 6.865,2.385 0.458,0.198 10 false SST 0.083,0.125 0.542,0.323 0.458,0.198 10 false *A 3.792,0.125 4.25,0.323 0.458,0.198 10 false *B
*A for 7GR-FKS *B for 1GD-FTV


Maximum non-alignment:

0.5 mm (0.0197 in.)


If the alignment is more than the maximum, using SST, adjust the diaphragm spring tip alignment.

SST
09333-00013  


Hide 31236B 5.INSTALL RELEASE FORK SUPPORT

a.

Install the release fork support to the manual transmission assembly.

Torque:
for 7GR-FKS : 47.1 N*m (480 kgf*cm, 35 ft.*lbf)
for 1GD-FTV : 49 N*m (500 kgf*cm, 36 ft.*lbf)


Hide 31230 6.INSTALL CLUTCH RELEASE BEARING ASSEMBLY

a.
C327838C01
0,0 0,0 false
V100135

Toyota Genuine Clutch Release Hub Grease or equivalent (mineral ingredients should not be included)


Apply grease to the clutch release bearing assembly.

Grease:

Toyota Genuine Clutch Release Hub Grease or equivalent (mineral ingredients should not be included)


Amount of Grease:

0.3 to 0.5 g (0.011 to 0.018 oz)


HINT:

When replacing the clutch release bearing assembly with a new one, do not apply grease.



b.
C410755C01
0.083,0.125 0.396,0.323 0.313,0.198 10 false *A 0.135,2.083 0.448,2.281 0.313,0.198 10 false *B 0.146,2.365 0.458,2.563 0.313,0.198 10 false *a 0.594,2.219 0.906,2.417 0.313,0.198 10 false *a 1.052,0.563 1.365,0.76 0.313,0.198 10 false *a 0.104,1.052 0.417,1.25 0.313,0.198 10 false *a 2.49,2.344 2.802,2.542 0.313,0.198 10 false *b 1.594,3.24 1.906,3.438 0.313,0.198 10 false *c 1.833,0.24 2.146,0.438 0.313,0.198 10 false *b 3.177,1.229 3.375,1.427 0.198,0.198 10 false *c
*A for 7GR-FKS
*B for 1GD-FTV
*a The surfaces of the release fork that contact the release bearing
*b The surfaces of the release fork that contact the release fork support
*c The surfaces of the release fork that contact the push rod of the release cylinder
V100135

Toyota Genuine Clutch Release Hub Grease or equivalent (mineral ingredients should not be included)


Apply grease or equivalent to the following areas.

Grease:

Toyota Genuine Clutch Release Hub Grease or equivalent (mineral ingredients should not be included)


Amount of Grease:
for 7GR-FKS:
The surfaces of the release fork that contact the release bearing 0.3 to 0.6 g (0.01 to 0.02 oz)
The surfaces of the release fork that contact the release fork support 1.3 to 1.8 g (0.05 to 0.06 oz)
The surfaces of the release fork that contact the push rod of the release cylinder 0.5 to 0.9 g (0.02 to 0.03 oz)

for 1GD-FTV:
The surfaces of the release fork that contact the release bearing 1.0 to 1.3 g (0.04 to 0.05 oz)
The surfaces of the release fork that contact the release fork support 1.3 to 1.8 g (0.05 to 0.06 oz)
The surfaces of the release fork that contact the push rod of the release cylinder 0.5 to 0.9 g (0.02 to 0.03 oz)



c.

Install the release fork sub-assembly to the clutch release bearing assembly.


d.

Install the clutch release bearing assembly together with the clutch release fork sub-assembly to the clutch housing.

NOTICE:

After the installation, move the fork forward and backward to check that the release bearing slides smoothly.



Hide 31126 7.INSTALL CLUTCH RELEASE FORK BOOT (for 1GD-FTV)

a.

Install the clutch release fork boot to the manual transmission assembly.