The ECM monitors the internal fuel pressure of the common rail assembly using the fuel pressure sensor, and controls the pre-stroke control valve to regulate the internal pressure so that it reaches the target pressure. The pressure sensor is a semiconductor that varies electrical resistance when pressure is applied to its silicon chip. This sensor outputs a voltage in proportion to the internal fuel pressure.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
| P008700 | Fuel Rail / System Pressure - Too Low | Fuel pressure sensor output voltage stays at fixed value a certain number of times (0.1 seconds or more) (1 trip detection logic). | ·
Open or short in fuel pressure sensor circuit ·
Fuel pressure sensor (common rail assembly) ·
Ran out of fuel ·
Fuel frozen |
Comes on | DTC stored | SAE Code: P0087 |
| P019011 | Fuel Rail Pressure Sensor "A" Circuit Short to Ground | Fuel pressure sensor output voltage (main) is 0.55 V or less for 0.5 seconds (1 trip detection logic). | ·
Short in fuel pressure sensor circuit ·
Fuel pressure sensor (common rail assembly) ·
ECM
|
Comes on | DTC stored | SAE Code: P0192 |
| P019015 | Fuel Rail Pressure Sensor "A" Circuit Short to Battery or Open | Fuel pressure sensor output voltage (main) is 4.9 V or higher for 0.5 seconds (1 trip detection logic). | ·
Open or short in fuel pressure sensor circuit ·
Fuel pressure sensor (common rail assembly) ·
ECM
|
Comes on | DTC stored | SAE Code: P0193 |
| P107A11 | Fuel Rail Pressure Sensor (Low) / Fuel Rail Pressure Sensor "B" Circuit Short to Ground | Fuel pressure sensor output voltage (sub) is 0.55 V or less for 0.5 seconds (1 trip detection logic). | ·
Short in fuel pressure sensor circuit ·
Fuel pressure sensor (common rail assembly) ·
ECM
|
Comes on | DTC stored | SAE Code: P107C |
| P107A15 | Fuel Rail Pressure Sensor (Low) / Fuel Rail Pressure Sensor "B" Circuit Short to Battery or Open | Fuel pressure sensor output voltage (sub) is 4.9 V or higher for 0.5 seconds (1 trip detection logic). | ·
Open or short in fuel pressure sensor circuit ·
Fuel pressure sensor (common rail assembly) ·
ECM
|
Comes on | DTC stored | SAE Code: P107D |
| DTC No. | Data List |
|---|---|
| P008700
P019011 P019015 P107A11 P107A15 |
·
Target Fuel Pressure (High) ·
Fuel Pressure (High) ·
Fuel Pressure (Low) / Fuel Pressure 2 |
Check Fuel Pressure (High) and compare it to Target Fuel Pressure (High) in the Data List by entering the following menus: Powertrain / Engine / Data List / Fuel Pressure (High), Target Fuel Pressure (High). Under stable conditions, the difference between Fuel Pressure (High) and Target Fuel Pressure (High) is 5000 kPag or less.
For more information on the fuel pressure sensor and common rail system, refer to System Description (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>SYSTEM DESCRIPTION).
If DTC P008700 is stored, the following symptoms may appear:
Black smoke
Poor drivability
Lack of power
Lack of power due to accelerator restriction performed by fail-safe function
If DTC P019011, P019015, P107A11 and/or P107A15 is stored, the following symptom may appear:
Lack of power due to accelerator restriction performed by fail-safe function
If DTC P019011, P019015, P107A11 and/or P107A15 is stored, "Fuel Pressure (High)" always displays 0 kPag or 240000 kPag.
| DTC No. | DTC Detection Drive Pattern |
|---|---|
| P008700 | After idling for 60 seconds, quickly increase engine speed to 2500 rpm repeatedly for 30 seconds |
| P019011
P019015 P107A11 P107A15 |
Ignition switch ON for 1 second or more |
Under normal conditions, the internal fuel pressure of the common rail assembly usually fluctuates by 1000 to 2000 kPag (10 to 20 kgf/cm2, 145 to 290 psi) even when driving conditions are constant. This DTC is stored if there is no fluctuation of the fuel pressure. The internal fuel pressure is approximately 30000 to 50000 kPag (305.9 to 509.9 kgf/cm2, 4350 to 7250 psi) when idling, and it increases to approximately 65000 to 110000 kPag (662.8 to 1121.7 kgf/cm2, 9425 to 15950 psi) when running the engine at 3000 rpm.
If this DTC is stored, the ECM enters fail-safe mode and limits engine power. The ECM continues operating in fail-safe mode until the ignition switch is turned off.
The diagram below indicates that fuel pressure rises as engine speed increases, but for the malfunction indicated by this DTC, that does not happen.
Even when the system is normal, DTCs may be stored due to a drop in fuel pressure as a result of the vehicle running out of fuel.
When P008700 and vehicle control history code X0806 are stored at the same time, clear the DTCs and check for DTCs once more.
These DTCs are stored if the fuel pressure sensor output voltage is out of the standard range due to an open or short malfunction of the sensor circuit.
If these DTCs are stored, the ECM enters fail-safe mode and limits the engine power. The ECM continues operating in fail-safe mode until the ignition switch is turned off.
After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>REGISTRATION) and initialization (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>INITIALIZATION).
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC P019011, P019015, P107A11 or P107A15 is output | A |
| DTC P008700 is output* | B |
*: When P008700 and vehicle control history code X0806 are stored, they may be stored as a result of a drop in fuel pressure due to the vehicle running out of fuel. Therefore, clear the DTCs and check that the DTCs are not stored again.
A
B
| *a | Component with harness connected
(ECM) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| E7-28 (VCM) - E7-19 (E2M) | Ignition switch ON | 4.5 to 5.5 V |
| E8-22 (VCS) - E8-21 (E2S) | Ignition switch ON | 4.5 to 5.5 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected
(ECM) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E7-18 (PCR1) - E7-19 (E2M) | Idling | 1.8 to 2.1 V |
| E8-23 (PCR2) - E8-21 (E2S) | Idling | 1.3 to 1.6 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the ignition switch to ON.
Connect the GTS to the DLC3.
Clear the DTCs.
Turn the ignition switch off for 30 seconds or more.
Turn the ignition switch to ON for 1 second or more.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC P019011, P019015, P107A11 or P107A15 is output | A |
| DTC is not output | B |
B
A
| *a | Front view of wire harness connector
(to Fuel Pressure Sensor) |
Disconnect the fuel pressure sensor connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| E105-6 (VC) - E105-4 (E2) | Ignition switch ON | 4.5 to 5.5 V |
| E105-1 (VCS) - E105-3 (E2S) | Ignition switch ON | 4.5 to 5.5 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the fuel pressure sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E105-5 (PR) - E7-18 (PCR1) | Always | Below 1 Ω |
| E105-4 (E2) - E7-19 (E2M) | Always | Below 1 Ω |
| E105-2 (PR2) - E8-23 (PCR2) | Always | Below 1 Ω |
| E105-3 (E2S) - E8-21 (E2S) | Always | Below 1 Ω |
| E105-5 (PR) or E7-18 (PCR1) - Body ground and other terminals | Always | 10 kΩ or higher |
| E105-2 (PR2) or E8-23 (PCR2) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the fuel pressure sensor connector.
| *a | Front view of wire harness connector
(to Fuel Pressure Sensor) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| E105-6 (VC) - E105-5 (PR) | Ignition switch off | No short or no open circuit |
| E105-5 (PR) - E105-4 (E2) | Ignition switch off | No short or no open circuit |
| E105-1 (VCS) - E105-2 (PR2) | Ignition switch off | No short or no open circuit |
| E105-2 (PR2) - E105-3 (E2S) | Ignition switch off | No short or no open circuit |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the common rail assembly.
Click hereEngine / Hybrid System>1GD-FTV (FUEL)>COMMON RAIL>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Bleed the air from the fuel system.
Click hereEngine / Hybrid System>1GD-FTV (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Clear the DTCs.
Turn the ignition switch off for 30 seconds or more.
Turn the ignition switch to ON.
Let the engine idle for 60 seconds, and then quickly increase the engine speed to 2500 rpm repeatedly for 30 seconds.
Confirm that the DTC is not output again.
Perform the following procedure using the GTS to determine whether or not the DTC judgment has been carried out.
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
| Tester Display |
|---|
| All Readiness |
Input DTC P008700, P019011, P019015, P107A11 or P107A15.
Check that STATUS is NORMAL. If STATUS is INCOMPLETE, increase the idling time.
| Proceed to |
|---|
| NEXT |
NEXT
Replace the ECM.
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Repair or replace the harness or connector.
| Proceed to |
|---|
| NEXT |
NEXT