Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ Urea SCR System) › 2019.02–2021.07
RM35X0E _51 Engine / Hybrid System _078856 1GD-FTV ENGINE CONTROL _0382589 ECD SYSTEM(w/ Urea SCR System) C

1GD-FTV ENGINE CONTROL  ECD SYSTEM(w/ Urea SCR System)  P048718  Exhaust Gas Recirculation Throttle Control Circuit "A" Low Circuit Current Below Threshold  P048719  Exhaust Gas Recirculation Throttle Control Circuit "A" High Circuit Current Above Threshold  


DESCRIPTION

The throttle actuator is operated by the ECM and opens and closes the throttle valve using gears. The opening angle of the throttle valve is detected by the throttle position sensor, which is mounted on the diesel throttle body assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P048718 Exhaust Gas Recirculation Throttle Control Circuit "A" Low Circuit Current Below Threshold Both of the following conditions are met for 2.0 seconds (1 trip detection logic):
·

The throttle actuator duty cycle is 80% or higher.

·

The throttle actuator current is less than 0.5 A.


·

Open or short in throttle actuator circuit

·

Diesel throttle body assembly

·

ECM


Comes on DTC stored SAE Code: P2141
P048719 Exhaust Gas Recirculation Throttle Control Circuit "A" High Circuit Current Above Threshold Either of the following conditions is met for 2.0 seconds (1 trip detection logic):
·

Throttle actuator current of 7 A or higher is detected.

·

The ECM internal circuit temperature of 150°C (302°F) or higher is detected.


·

Open or short in throttle actuator circuit

·

Diesel throttle body assembly

·

ECM


Comes on DTC stored SAE Code: P2142

Related Data List
DTC No. Data List
P048718
P048719
Diesel Throttle Motor Duty Bank 1

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P048718
P048719
Idle the engine for 5 seconds or more

WIRING DIAGRAM

A348546E14
0.208,2.531 0.771,2.844 0.563,0.313 10 false E103 0.208,2.719 2.604,3.125 2.396,0.406 10 false Throttle Actuator (Built into Diesel Throttle Body Assembly) 1.458,1.365 1.771,1.563 0.313,0.198 10 false 2 1.469,2.094 1.781,2.292 0.313,0.198 10 false 1 4.906,1.125 5.219,1.323 0.313,0.198 10 false M+ 4.917,1.865 5.229,2.063 0.313,0.198 10 false M- 5.552,1.167 6.688,1.563 1.135,0.396 10 false Throttle Actuator Control Circuit 4.667,1.354 4.979,1.552 0.313,0.198 10 false 5 4.688,2.104 5,2.302 0.313,0.198 10 false 4 5.323,3.146 5.635,3.344 0.313,0.198 10 false E7 5.292,3.333 5.74,3.531 0.448,0.198 10 false ECM 1.146,1.125 1.458,1.323 0.313,0.198 10 false M+ 1.146,1.854 1.458,2.052 0.313,0.198 10 false M-

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>REGISTRATION) and initialization (Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.INSPECT DIESEL THROTTLE BODY ASSEMBLY
a.

Remove the diesel throttle body assembly.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>DIESEL THROTTLE BODY>REMOVAL


b.
A327312C19
0.135,0.125 0.448,0.281 0.313,0.156 10 false *a
*a Component without harness connected
(Diesel Throttle Body Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 Always No short or no open circuit



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (DIESEL THROTTLE BODY ASSEMBLY - ECM)

NG

6.REPLACE DIESEL THROTTLE BODY ASSEMBLY
2.CHECK HARNESS AND CONNECTOR (DIESEL THROTTLE BODY ASSEMBLY - ECM)
a.

Disconnect the diesel throttle body assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E103-2 (M+) - E7-5 (M+) Always Below 1 Ω
E103-1 (M-) - E7-4 (M-) Always Below 1 Ω
E103-2 (M+) or E7-5 (M+) - Body ground and other terminals Always 10 kΩ or higher
E103-1 (M-) or E7-4 (M-) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.REPLACE ECM

NG

4.REPAIR OR REPLACE HARNESS OR CONNECTOR
3.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
4.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

e.

Turn the ignition switch off and wait for 30 seconds.


f.

Start the engine.


g.

Idle the engine for 5 seconds or more.


h.

Turn the GTS on.


i.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 372

j.

Confirm that the DTC is not output.


Result:
Proceed to
NEXT



NEXT

END

6.REPLACE DIESEL THROTTLE BODY ASSEMBLY
a.

Replace the diesel throttle body assembly.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>DIESEL THROTTLE BODY>REMOVAL


Result:
Proceed to
NEXT



NEXT

5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED