A nitrogen oxides sensor is installed in the front exhaust pipe assembly in order to detect the concentration of NOx and O2 in the exhaust gas.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
| P013613 | O2 Sensor Circuit Bank 1 Sensor 2 Circuit Open | Nitrogen oxides sensor malfunction for 3 seconds or more (2 trip detection logic). | Nitrogen oxides sensor | Comes on | DTC stored | SAE Code: P0136 |
| P220011 | NOx Sensor Circuit Low Bank 1 Sensor 1 Circuit Short to Ground | Nitrogen oxides sensor malfunction for 3 seconds or more (2 trip detection logic). | Nitrogen oxides sensor | Comes on | DTC stored | SAE Code: P2202 |
| P220012 | NOx Sensor Circuit High Bank 1 Sensor 1 Circuit Short to Battery | Nitrogen oxides sensor malfunction for 3 seconds or more (2 trip detection logic). | Nitrogen oxides sensor | Comes on | DTC stored | SAE Code: P2203 |
| P220013 | NOx Sensor Circuit Low Bank 1 Sensor 1 Circuit Open | Nitrogen oxides sensor malfunction for 3 seconds or more (2 trip detection logic). | Nitrogen oxides sensor | Comes on | DTC stored | SAE Code: P2200 |
| P220512 | NOx Sensor Heater Control Circuit High Bank 1 Sensor 1 Circuit Short to Battery | Nitrogen oxides sensor malfunction for 3 seconds or more (2 trip detection logic). | Nitrogen oxides sensor | Comes on | DTC stored | SAE Code: P2207 |
| P220514 | NOx Sensor Heater Control Circuit Low Bank 1 Sensor 1 Circuit Short to Ground or Open | Nitrogen oxides sensor malfunction for 3 seconds or more (2 trip detection logic). | Nitrogen oxides sensor | Comes on | DTC stored | SAE Code: P2206 |
| DTC No. | Data List |
|---|---|
| P013613
P220011 P220012 P220013 P220512 P220514 |
NOx Density B1S1 |
| DTC No. | DTC Detection Drive Pattern |
|---|---|
| P013613
P220011 P220012 P220013 P220512 P220514 |
Ignition switch ON for 3 seconds or more |
Refer to DTC U029D87.
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>U029D87
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC P013613, P220011, P220012, P220013, P220512 OR P220514 is output | A |
| DTC P013613, P220011, P220012, P220013, P220512 OR P220514 and other DTCs are output* | B |
*: If any other DTCs are output, perform troubleshooting for those DTCs first.
A
B
Replace the nitrogen oxides sensor.
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>NITROGEN OXIDES SENSOR>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Clear the DTCs.
Turn the ignition switch off and wait for 30 seconds or more.
Ignition switch to ON for 3 seconds or more.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Confirm that the DTC is not output again.
| Proceed to |
|---|
| NEXT |
NEXT