Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ Urea SCR System) › 2019.02–2021.07
RM35X0E _51 Engine / Hybrid System _078856 1GD-FTV ENGINE CONTROL _0382589 ECD SYSTEM(w/ Urea SCR System) C

1GD-FTV ENGINE CONTROL  ECD SYSTEM(w/ Urea SCR System)  U029D87  Lost Communication with NOx Sensor "A" Missing Message  


DESCRIPTION

The ECM sends and receives data to and from the nitrogen oxides sensor via local CAN communication.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
U029D87 Lost Communication with NOx Sensor "A" Missing Message Communication stops between the ECM and the nitrogen oxides sensor for 1 second or more (1 trip detection logic).
·

Nitrogen oxides sensor

·

Harness or connector

·

No. 1 integration relay

·

ECM


Comes on DTC stored SAE Code: U029D

MONITOR DESCRIPTION

The ECM stores a DTC when a communication malfunction occurs between the nitrogen oxides sensor and ECM.

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
U029D87 Ignition switch ON and wait for 1 second or more.

WIRING DIAGRAM

A444443E02
5.052,1.333 5.51,1.531 0.458,0.198 10 false GND 4.521,0.5 4.979,0.698 0.458,0.198 10 false BATT 5.969,0.531 6.427,0.729 0.458,0.198 10 false CANU 5.969,1.031 6.427,1.229 0.458,0.198 10 false CAND 5.75,0.885 6.063,1.083 0.313,0.198 10 false 35 5.74,0.385 6.052,0.583 0.313,0.198 10 false 27 5,0.542 5.458,0.74 0.458,0.198 10 false CAN+ 5.031,1.031 5.49,1.229 0.458,0.198 10 false CAN- 5.427,0.875 5.74,1.073 0.313,0.198 10 false 3 5.427,0.375 5.74,0.573 0.313,0.198 10 false 2 5.438,1.25 5.75,1.448 0.313,0.198 10 false 4 4.344,0.385 4.615,0.583 0.271,0.198 10 false 5 3.875,0.49 4.333,0.688 0.458,0.198 10 false 1E 3.917,0.313 4.229,0.51 0.313,0.198 10 false 3 1.031,2.344 1.49,2.542 0.458,0.198 10 false 1E 1.094,2.146 1.406,2.344 0.313,0.198 10 false 4 1.76,0.625 2.219,0.823 0.458,0.198 10 false NOX 3.302,2 4.031,2.229 0.729,0.229 10 false EFI NO. 2 2.667,1.26 3.125,1.458 0.458,0.198 10 false NOX 1.073,1.854 1.531,2.052 0.458,0.198 10 false A 1.073,1.667 1.385,1.865 0.313,0.198 10 false 1 1.656,0.354 1.969,0.552 0.313,0.198 10 false 1 2.021,0.344 2.333,0.542 0.313,0.198 10 false 2 3.729,1.75 4.042,1.948 0.313,0.198 10 false 2 3.24,3.49 3.552,3.688 0.313,0.198 10 false 5 2.615,4.354 3.344,4.583 0.729,0.229 10 false EFI MAIN 3.333,1.771 3.646,1.969 0.313,0.198 10 false 1 2.448,3.5 2.76,3.698 0.313,0.198 10 false 3 0.948,3.719 1.677,3.948 0.729,0.229 10 false EFI-MAIN 0.531,3.969 1.26,4.198 0.729,0.229 10 false FL MAIN 0.698,4.656 1.427,4.885 0.729,0.229 10 false Battery 1.969,2.958 4.281,3.146 2.313,0.188 10 false No. 1 Integration Relay 1.948,4.927 4.125,5.115 2.177,0.188 10 false : CAN Communication Line 4.521,1.729 5.635,2.115 1.115,0.385 10 false Nitrogen Oxides Sensor Assembly 4.531,1.552 4.99,1.75 0.458,0.198 10 false Y3 6.208,4.583 6.667,4.781 0.458,0.198 10 false ECM 6.281,4.385 6.74,4.583 0.458,0.198 10 false N2 5.99,3.979 6.448,4.177 0.458,0.198 10 false MREL 5.719,3.854 6.031,4.052 0.313,0.198 10 false 14 3.229,3.896 3.542,4.094 0.313,0.198 10 false 2 2.469,3.875 2.781,4.073 0.313,0.198 10 false 1 1.406,3.469 1.719,3.667 0.313,0.198 10 false 2 0.948,3.49 1.26,3.688 0.313,0.198 10 false 1 3.74,3.75 4.469,3.979 0.729,0.229 10 false EFI NO. 3 3.75,3.5 4.063,3.698 0.313,0.198 10 false 1 4.198,3.49 4.51,3.688 0.313,0.198 10 false 2 3.885,2.333 4.344,2.531 0.458,0.198 10 false 1E 3.927,2.167 4.24,2.365 0.313,0.198 10 false 8 1.896,1.99 2.448,2.354 0.552,0.365 10 false E/G W/PMP 2.448,2.615 3.458,2.906 1.01,0.292 10 false E/G W/PMP

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses of circuits related to this system before performing the following inspection procedure.


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

According to the display on the GTS, select "Health Check".


d.

Check for currently output system DTCs.

Result:
Result Proceed to
DTC U029D87 is output A
DTC U029D87 and other DTCs are output* B


HINT:

*: If any other DTCs are output, perform troubleshooting for those DTCs first.




A

2.CHECK NITROGEN OXIDES SENSOR

B

2.CHECK NITROGEN OXIDES SENSOR
a.

Disconnect the nitrogen oxides sensor connector.


b.

Turn the ignition switch to ON.


c.
A383897C06
1.469,0.198 1.948,0.531 0.479,0.333 1.656,1.833 1.76,1.833 1.76,1.833 1.885,1.271 true 2.5,1.833 2.333,1.833 2.333,1.833 2.198,1.271 true 0.188,0.135 0.5,0.333 0.313,0.198 10 false *a 1.625,0.292 1.938,0.49 0.313,0.198 10 false Y3 1.333,1.76 1.792,1.958 0.458,0.198 10 false GND 2.552,1.76 3.094,1.958 0.542,0.198 10 false BATT
*a Front view of wire harness connector
(to Nitrogen Oxides Sensor)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
Y3-5 (BATT) - Y3-4 (GND) Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (NITROGEN OXIDES SENSOR - ECM)

NG

6.CHECK HARNESS AND CONNECTOR (NITROGEN OXIDES SENSOR - BODY GROUND)
3.CHECK HARNESS AND CONNECTOR (NITROGEN OXIDES SENSOR - ECM)
a.

Disconnect the nitrogen oxides sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Y3-2 (CAN+) - N2-27 (CANU) Always Below 1 Ω
Y3-3 (CAN-) - N2-35 (CAND) Always Below 1 Ω
Y3-2 (CAN+) or N2-27 (CANU) - Body ground and other terminals Always 10 kΩ or higher
Y3-3 (CAN-) or N2-35 (CAND) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.REPLACE NITROGEN OXIDES SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.REPLACE NITROGEN OXIDES SENSOR

Result:
Proceed to
NEXT



NEXT

5.CHECK DTC OUTPUT
5.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

d.

Turn the ignition switch off for 30 seconds or more.


e.

Turn the ignition switch to ON and wait for 1 second or more.


f.

Turn the GTS on.


g.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 372

h.

Read the DTCs.


Result:
Result Proceed to
No DTC is output A
DTC U029D87 is output B



A

END

B

6.CHECK HARNESS AND CONNECTOR (NITROGEN OXIDES SENSOR - BODY GROUND)
a.

Disconnect the nitrogen oxides sensor connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Y3-4 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

7.INSPECT NO. 1 INTEGRATION RELAY (NOX RELAY AND E/G W/PMP RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT NO. 1 INTEGRATION RELAY (NOX RELAY AND E/G W/PMP RELAY)
a.

Inspect the No. 1 integration relay (NOX relay).

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>RELAY>ON-VEHICLE INSPECTION


b.

Inspect the No. 1 integration relay (E/G W/PMP relay).

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>RELAY>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - BODY GROUND)

NG

REPLACE NO. 1 INTEGRATION RELAY

8.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - BODY GROUND)
a.

Remove the No. 1 integration relay from the No. 1 engine room relay block and junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1E-4 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (NITROGEN OXIDES SENSOR - NO. 1 INTEGRATION RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK HARNESS AND CONNECTOR (NITROGEN OXIDES SENSOR - NO. 1 INTEGRATION RELAY)
a.

Disconnect the nitrogen oxides sensor connector.


b.

Remove the No. 1 integration relay from the No. 1 engine room relay block and junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Y3-5 (BATT) - 1E-3 Always Below 1 Ω
Y3-5 (BATT) or 1E-3 - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

10.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - EFI MAIN RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - EFI MAIN RELAY)
a.

Remove the EFI MAIN relay from the No. 1 engine room relay block and junction block assembly.


b.

Remove the No. 1 integration relay from the No. 1 engine room relay block and junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1E-8 - EFI MAIN relay terminal 5 Always Below 1 Ω
1E-8 or EFI MAIN relay terminal 5 - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR