If DTC P223711, P223712, P223713, P223716, P223717, P225111 and/or P225112 is present, refer to the DTC table for DPF system.
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>SYSTEM DESCRIPTION
Refer to DTC P003012.
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>P003012
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
| P223711 | A/F (O2) Sensor Positive Current Control Bank 1 Sensor 1 Circuit Short to Ground | The A1A+ voltage is 1.26 V or less for 5 seconds or more (1 trip detection logic). | ·
Short in air fuel ratio sensor circuit ·
Air fuel ratio sensor ·
ECM |
Comes on | DTC stored | SAE Code: P2238 |
| P223712 | A/F (O2) Sensor Positive Current Control Bank 1 Sensor 1 Circuit Short to Battery | The A1A+ voltage is higher than 4.47 V for 5 seconds or more (1 trip detection logic). | ·
Open in air fuel ratio sensor circuit ·
Air fuel ratio sensor ·
ECM |
Comes on | DTC stored | SAE Code: P2239 |
| P223713 | A/F (O2) Sensor Positive Current Control Bank 1 Sensor 1 Circuit Open | An open or ground short in the circuit between terminals A1A+ and A1A- of the air fuel ratio sensor (sensor 1) while the engine is running (1 trip detection logic). | ·
Open or short in air fuel ratio sensor circuit ·
Air fuel ratio sensor ·
ECM |
Comes on | DTC stored | SAE Code: P2237 |
| P223716 | A/F (O2) Sensor Positive Current Control Bank 1 Sensor 1 Circuit Voltage Below Threshold | Difference between terminals A1A+ and A1A- is 0.1 V or less for 5 seconds or more (1 trip detection logic). | ·
Open or short in air fuel ratio sensor circuit ·
Air fuel ratio sensor ·
ECM |
Comes on | DTC stored | SAE Code: P2238 |
| P223717 | A/F (O2) Sensor Positive Current Control Bank 1 Sensor 1 Circuit Voltage Above Threshold | Difference between terminals A1A+ and A1A- is higher than 1.0 V for 5 seconds or more (1 trip detection logic). | ·
Open or short in air fuel ratio sensor circuit ·
Air fuel ratio sensor ·
ECM |
Comes on | DTC stored | SAE Code: P2239 |
| P225111 | O2 Sensor Negative Current Control Bank 1 Sensor 1 Circuit Short to Ground | The A1A- voltage is 1.07 V or less for 5 seconds or more (1 trip detection logic). | ·
Short in air fuel ratio sensor circuit ·
Air fuel ratio sensor ·
ECM |
Comes on | DTC stored | SAE Code: P2252 |
| P225112 | O2 Sensor Negative Current Control Bank 1 Sensor 1 Circuit Short to Battery | The A1A- voltage is higher than 3.93 V for 5 seconds or more (1 trip detection logic). | ·
Open or short in air fuel ratio sensor circuit ·
Air fuel ratio sensor ·
ECM |
Comes on | DTC stored | SAE Code: P2253 |
| DTC No. | Data List |
|---|---|
| P223711
P223712 P223713 P223716 P223717 P225111 P225112 |
·
A/F (O2) Lambda B1S1 ·
Exhaust Temperature B1S2 |
The air fuel ratio sensor outputs a voltage in proportion to the air fuel ratio. If impedance (alternating current resistance) or voltage output of the sensor deviates greatly from the standard range, the ECM interprets this as an open or short malfunction of the air fuel ratio sensor circuit.
| DTC No. | DTC Detection Drive Pattern |
|---|---|
| P223713 | Drive the vehicle at 50 km/h (30 mph) or more for a total of 300 seconds or more.
|
| P223711
P223712 P223716 P223717 P225111 P225112 |
Ignition switch ON for 5 seconds. |
Refer to DTC P003012.
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>P003012
After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>REGISTRATION) and initialization (Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>INITIALIZATION).
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
| *a | Front view of wire harness connector
(to Air Fuel Ratio Sensor) |
Make sure that the connector is properly connected. If it is not, securely connect it and check for DTCs again.
Disconnect the air fuel ratio sensor connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E19-3 (A1A+) - Body ground | Ignition switch ON | 2.8 to 3.0 V |
| E19-4 (A1A-) - Body ground | Ignition switch ON | 2.3 to 2.7 V |
| E19-3 (A1A+) - E19-4 (A1A-) | Ignition switch ON | 0.1 to 0.7 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the air fuel ratio sensor.
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>AIR FUEL RATIO SENSOR>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Disconnect the air fuel ratio sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E19-3 (A1A+) - E6-33 (A1A+) | Always | Below 1 Ω |
| E19-4 (A1A-) - E6-25 (A1A-) | Always | Below 1 Ω |
| E19-3 (A1A+) - E6-33 (A1A+) - Body ground and other terminals | Always | 10 kΩ or higher |
| E19-4 (A1A-) or E6-25 (A1A-) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the ECM.
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Repair or replace the harness or connector.
| Proceed to |
|---|
| NEXT |
NEXT
Warm up the engine (engine coolant temperature is 75°C (167°F) or higher).
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs.
Turn the ignition switch off and wait for 30 seconds.
Start the engine and turn the GTS on.
Drive the vehicle at 50 km/h (30 mph) or more for a total of 300 seconds or more.
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
Make sure that the exhaust gas temperature (Exhaust Temperature B1S2) is 200°C (392°F) or higher.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Confirm that the DTC is not output again.
| Proceed to |
|---|
| NEXT |
NEXT