Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ Urea SCR System) › 2019.02–2021.07
RM35X0E _51 Engine / Hybrid System _078856 1GD-FTV ENGINE CONTROL _0382589 ECD SYSTEM(w/ Urea SCR System) C

1GD-FTV ENGINE CONTROL  ECD SYSTEM(w/ Urea SCR System)  U010E87  Lost Communication with Reductant Control Module Missing Message  


DESCRIPTION

The ECM sends and receives data to and from the urea pump control ECU via local CAN communication.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
U010E87 Lost Communication with Reductant Control Module Missing Message Communication stops between the ECM and the urea pump control ECU for 1.6 second or more (1 trip detection logic).
·

Urea pump control ECU

·

Harness or connector

·

DCU MAIN relay

·

ECM


Comes on DTC stored SAE Code: U010E

MONITOR DESCRIPTION

The ECM stores a DTC when a communication malfunction occurs between the ECM and urea pump control ECU.

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
U010E87 1.6 seconds or more after turning the ignition switch to ON.

WIRING DIAGRAM

A436525E01
2.615,0.531 3.573,0.729 0.958,0.198 10 false IG2-MAIN 4.906,0.521 5.729,0.719 0.823,0.198 10 false IG2 NO. 1 3.438,1.073 4.115,1.302 0.677,0.229 10 false IG2 MAIN 3.031,2.406 4.688,2.594 1.656,0.188 10 false Ignition Switch Assembly 3.01,2.271 3.323,2.469 0.313,0.198 10 false N28 3.271,1.802 3.729,2 0.458,0.198 10 false AM2 4.021,1.802 4.479,2 0.458,0.198 10 false IG2 4.344,1.802 4.5,2 0.156,0.198 10 false 2 3.115,1.802 3.271,2 0.156,0.198 10 false 1 2.031,7.302 5.698,7.5 3.667,0.198 10 false : CAN Communication Line 0.646,5.302 1.375,5.49 0.729,0.188 10 false FL MAIN 0.76,6.802 1.469,6.99 0.708,0.188 10 false Battery 3.677,6.135 4.135,6.333 0.458,0.198 10 false N2 3.677,6.302 4.135,6.5 0.458,0.198 10 false ECM 4.583,2.885 5.49,3.073 0.906,0.188 10 false ECU-B NO. 3 4.635,3.958 5.656,4.135 1.021,0.177 10 false DCU NO. 2 4.635,3.448 5.5,3.635 0.865,0.188 10 false DCU NO. 1 2.063,0.188 2.219,0.385 0.156,0.198 10 false 1 4.99,0.24 5.146,0.438 0.156,0.198 10 false 1 5.25,0.24 5.406,0.438 0.156,0.198 10 false 2 3,4.198 3.156,4.396 0.156,0.198 10 false 5 2.25,4.198 2.406,4.396 0.156,0.198 10 false 3 2.26,4.594 2.417,4.792 0.156,0.198 10 false 1 3,4.594 3.156,4.792 0.156,0.198 10 false 2 3.823,5.208 4.438,5.406 0.615,0.198 10 false CANH 3.833,5.698 4.448,5.896 0.615,0.198 10 false CANL 5.333,7.302 7.135,7.573 1.802,0.271 11 false Urea Pump Control ECU 5.333,7.073 5.646,7.271 0.313,0.198 10 false N37 6.094,0.375 6.708,0.573 0.615,0.198 10 false IGSW 5.823,0.26 6.135,0.458 0.313,0.198 10 false 18 6.094,2.729 6.708,2.927 0.615,0.198 10 false BATT 6.073,3.031 6.688,3.229 0.615,0.198 10 false +BU5 6.073,3.281 6.688,3.479 0.615,0.198 10 false +BU4 6.073,3.552 6.688,3.75 0.615,0.198 10 false +BU3 6.073,3.802 6.688,4 0.615,0.198 10 false +BU2 6.083,4.302 6.698,4.5 0.615,0.198 10 false +BU1 6.073,4.719 6.688,4.917 0.615,0.198 10 false UREL 6.073,5.208 6.688,5.406 0.615,0.198 10 false CAN+ 6.073,5.719 6.688,5.917 0.615,0.198 10 false CAN- 6.104,6.094 6.563,6.292 0.458,0.198 10 false E01 6.104,6.365 6.563,6.563 0.458,0.198 10 false E02 6.104,6.625 6.563,6.823 0.458,0.198 10 false E03 5.833,2.635 6.146,2.833 0.313,0.198 10 false 30 5.875,2.927 6.031,3.125 0.156,0.198 10 false 2 5.875,3.198 6.031,3.396 0.156,0.198 10 false 1 5.833,3.458 6.146,3.656 0.313,0.198 10 false 19 5.833,3.708 6.146,3.906 0.313,0.198 10 false 10 5.833,4.229 6.146,4.427 0.313,0.198 10 false 11 5.875,4.615 6.031,4.813 0.156,0.198 10 false 9 4.313,5.052 4.625,5.25 0.313,0.198 10 false 17 4.323,5.542 4.635,5.74 0.313,0.198 10 false 28 5.823,5.052 6.135,5.25 0.313,0.198 10 false 27 5.802,5.552 6.115,5.75 0.313,0.198 10 false 26 5.823,5.99 6.135,6.188 0.313,0.198 10 false 52 5.823,6.25 6.135,6.448 0.313,0.198 10 false 51 5.823,6.51 6.135,6.708 0.313,0.198 10 false 50 1.188,4.458 1.646,4.688 0.458,0.229 10 false DCU 2.323,5.021 3.552,5.219 1.229,0.198 10 false DCU MAIN 2.135,2.094 2.594,2.333 0.458,0.24 10 false AM2 4.271,0.375 4.542,0.552 0.271,0.177 10 false 1D 4.271,0.781 4.542,0.958 0.271,0.177 10 false 1D 4.313,0.594 4.469,0.792 0.156,0.198 10 false 2 4.313,0.167 4.469,0.365 0.156,0.198 10 false 1 2.031,0.771 2.302,0.948 0.271,0.177 10 false 1E 2.073,0.365 2.344,0.542 0.271,0.177 10 false A 4.625,4.458 5.646,4.635 1.021,0.177 10 false DCU NO. 3 2.688,1.344 4.344,1.594 1.656,0.25 10 false No. 1 Integration Relay 2.073,0.594 2.229,0.792 0.156,0.198 10 false 4

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses of circuits related to this system before performing the following inspection procedure.


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

According to the display on the GTS, select "Health Check".


d.

Check for currently output system DTCs.

Result:
Result Proceed to
DTC U010E87 is output A
DTC U010E87 and other DTCs are output* B


HINT:

*: If any other DTCs are output, perform troubleshooting for those DTCs first.




A

2.CHECK HARNESS AND CONNECTOR (UREA PUMP CONTROL ECU - ECM)

B

2.CHECK HARNESS AND CONNECTOR (UREA PUMP CONTROL ECU - ECM)
a.

Disconnect the urea pump control ECU connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N37-27 (CAN+) - N2-17 (CANH) Always Below 1 Ω
N37-26 (CAN-) - N2-28 (CANL) Always Below 1 Ω
N37-27 (CAN+) or N2-17 (CANH) - Body ground and other terminals Always 10 kΩ or higher
N37-26 (CAN-) or N2-28 (CANL) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK UREA PUMP CONTROL ECU (BATT TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK UREA PUMP CONTROL ECU (BATT TERMINAL)
a.
A204368C14
0.25,1.135 0.646,1.375 0.396,0.24 2.458,1.021 2.25,1.813 true 0.25,0.167 0.427,0.344 0.177,0.177 10 false *a 1.948,1.865 2.729,2.063 0.781,0.198 10 false 30 (BATT) 0.333,1.177 0.719,1.396 0.385,0.219 10 false N37
*a Front view of wire harness connector
(to Urea Pump Control ECU)


Disconnect the urea pump control ECU connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
N37-30 (BATT) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK UREA PUMP CONTROL ECU (IGSW TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (UREA PUMP CONTROL ECU - BATTERY)

4.CHECK UREA PUMP CONTROL ECU (IGSW TERMINAL)
a.
A204368C15
0.25,1.135 0.646,1.375 0.396,0.24 2.365,0.948 2.167,1.802 true 0.25,0.167 0.427,0.344 0.177,0.177 10 false *a 1.948,1.865 2.729,2.063 0.781,0.198 10 false 18 (IGSW) 0.333,1.177 0.719,1.396 0.385,0.219 10 false N37
*a Front view of wire harness connector
(to Urea Pump Control ECU)


Disconnect the urea pump control ECU connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
N37-18 (IGSW) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

5.INSPECT DCU MAIN RELAY

NG

10.CHECK HARNESS AND CONNECTOR (IG2 NO. 1 FUSE - UREA PUMP CONTROL ECU)
5.INSPECT DCU MAIN RELAY

Result:
Proceed to
OK
NG



OK

6.CHECK UREA PUMP CONTROL ECU (UREL TERMINAL)

NG

REPLACE DCU MAIN RELAY

6.CHECK UREA PUMP CONTROL ECU (UREL TERMINAL)
a.
A444439C01
0.104,0.083 0.417,0.281 0.313,0.198 10 false *1 1.771,0.302 2.083,0.5 0.313,0.198 10 false *a
*1 No. 1 Engine Room Relay Block and Junction Block Assembly
*a DCU MAIN relay holder


Remove the DCU MAIN relay from the No. 1 engine room relay block and junction block assembly.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
DCU MAIN relay terminal 2 - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (DCU MAIN RELAY - UREA PUMP CONTROL ECU)

NG

9.CHECK HARNESS AND CONNECTOR (DCU MAIN RELAY - UREA PUMP CONTROL ECU)
7.CHECK HARNESS AND CONNECTOR (DCU MAIN RELAY - UREA PUMP CONTROL ECU)
A444440C02
5.083,0.531 5.417,0.74 0.333,0.208 4.229,2.156 4.948,1.167 true 4.844,2.156 5.031,1.177 true 5.458,2.156 5.635,1.156 true 5.719,1.146 5.906,0.719 5.906,0.719 6.073,0.719 true 6.281,2.177 5.719,1.24 true 0.271,0.219 0.583,0.417 0.313,0.198 10 false *1 1.635,0.219 1.948,0.417 0.313,0.198 10 false *a 3.844,0.25 4.156,0.448 0.313,0.198 10 false *b 5.125,0.542 5.438,0.74 0.313,0.198 10 false N37 3.906,2.219 4.615,2.417 0.708,0.198 10 false 1 (+BU4) 4.604,2.219 5.313,2.417 0.708,0.198 10 false 2 (+BU5) 5.313,2.219 6.021,2.417 0.708,0.198 10 false 10 (+BU2) 6.125,2.229 6.833,2.427 0.708,0.198 10 false 19 (+BU3) 6.146,0.625 6.854,0.823 0.708,0.198 10 false 11 (+BU1)
*1 No. 1 Engine Room Relay Block and Junction Block Assembly - -
*a DCU MAIN relay holder *b Front view of wire harness connector
(to Urea Pump Control ECU)


a.

Remove the DCU MAIN relay from the No. 1 engine room relay block and junction block assembly.


b.

Disconnect the urea pump control ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
DCU MAIN relay terminal 5 - N37-11 (+BU1) Always Below 1 Ω
DCU MAIN relay terminal 5 - N37-10 (+BU2) Always Below 1 Ω
DCU MAIN relay terminal 5 - N37-19 (+BU3) Always Below 1 Ω
DCU MAIN relay terminal 5 - N37-1 (+BU4) Always Below 1 Ω
DCU MAIN relay terminal 5 - N37-2 (+BU5) Always Below 1 Ω
DCU MAIN relay terminal 5 or N37-11 (+BU1) - Body ground and other terminals Always 10 kΩ or higher
DCU MAIN relay terminal 5 or N37-10 (+BU2) - Body ground and other terminals Always 10 kΩ or higher
DCU MAIN relay terminal 5 or N37-19 (+BU3) - Body ground and other terminals Always 10 kΩ or higher
DCU MAIN relay terminal 5 or N37-1 (+BU4) - Body ground and other terminals Always 10 kΩ or higher
DCU MAIN relay terminal 5 or N37-2 (+BU5) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (DCU MAIN RELAY - BATTERY, BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (DCU MAIN RELAY - BATTERY, BODY GROUND)
a.
A444439C01
0.104,0.083 0.417,0.281 0.313,0.198 10 false *1 1.771,0.302 2.083,0.5 0.313,0.198 10 false *a
*1 No. 1 Engine Room Relay Block and Junction Block Assembly
*a DCU MAIN relay holder


Remove the DCU MAIN relay from the No. 1 engine room relay block and junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
DCU MAIN relay terminal 1 - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
DCU MAIN relay terminal 3 - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (DCU MAIN RELAY - BATTERY, BODY GROUND)

9.CHECK HARNESS AND CONNECTOR (DCU MAIN RELAY - UREA PUMP CONTROL ECU)
A444440C01
5.125,0.573 5.458,0.781 0.333,0.208 5.385,2.063 5.573,1.156 true 0.271,0.25 0.583,0.448 0.313,0.198 10 false *1 1.635,0.219 1.948,0.417 0.313,0.198 10 false *a 3.906,0.25 4.219,0.448 0.313,0.198 10 false *b 5.177,0.594 5.49,0.792 0.313,0.198 10 false N37 5.167,2.125 5.917,2.323 0.75,0.198 10 false 9 (UREL)
*1 No. 1 Engine Room Relay Block and Junction Block Assembly - -
*a DCU MAIN relay holder *b Front view of wire harness connector
(to Urea Pump Control ECU)


a.

Remove the DCU MAIN relay from the No. 1 engine room relay block and junction block assembly.


b.

Disconnect the urea pump control ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
DCU MAIN relay terminal 2 - N37-9 (UREL) Always Below 1 Ω
DCU MAIN relay terminal 2 or N37-9 (UREL) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK HARNESS AND CONNECTOR (IG2 NO. 1 FUSE - UREA PUMP CONTROL ECU)
A444441C02
5.083,0.531 5.417,0.74 0.333,0.208 6.281,2.177 5.646,1.229 true 0.271,0.219 0.583,0.417 0.313,0.198 10 false *1 2.885,0.333 3.198,0.531 0.313,0.198 10 false *a 4.26,0.198 4.573,0.396 0.313,0.198 10 false *b 5.125,0.542 5.438,0.74 0.313,0.198 10 false N37 6.125,2.229 6.833,2.427 0.708,0.198 10 false 18 (IGSW)
*1 No. 1 Engine Room Relay Block and Junction Block Assembly - -
*a IG2 NO. 1 fuse holder *b Front view of wire harness connector
(to Urea Pump Control ECU)


a.

Remove the IG2 NO. 1 fuse from the No. 1 engine room relay block and junction block assembly.


b.

Disconnect the urea pump control ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
IG2 NO. 1 fuse terminal 2 - N37-18 (IGSW) Always Below 1 Ω
IG2 NO. 1 fuse terminal 2 or N37-18 (IGSW) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR