The side collision sensor LH circuit consists of the airbag sensor assembly, side airbag pressure sensor LH and No. 3 side airbag sensor LH.
The side airbag pressure sensor LH detects impacts to the vehicle and sends signals to the airbag sensor assembly to determine if the SRS should be deployed.
These DTCs are stored when a malfunction is detected in the side airbag pressure sensor LH or airbag sensor assembly.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Warning Indicate | Test Mode / Check Mode |
|---|---|---|---|---|---|
| B167A | Front Door Pressure Sensor LH | Either condition is met:
·
A side airbag pressure sensor LH malfunction. ·
An airbag sensor assembly malfunction. |
·
A side airbag pressure sensor LH malfunction. ·
An airbag sensor assembly malfunction. |
Comes on | Not applicable |
| B167E | Front Door Pressure Sensor Threshold Malfunction (LH) | Either condition is met:
·
A side airbag pressure sensor LH malfunction. ·
An airbag sensor assembly malfunction. |
·
A side airbag pressure sensor LH malfunction. ·
An airbag sensor assembly malfunction. |
Comes on | Not applicable |
After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) battery terminal.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY
When disconnecting and reconnecting the battery
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE
When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART
After replacing the airbag sensor assembly, refer to initialization.
Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE
| *1 | Side Airbag Pressure Sensor RH |
| *2 | No. 3 Side Airbag Sensor LH |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Interchange the side airbag pressure sensor LH with RH and connect the connectors to them.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in memory.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for Type B)>DTC CHECK / CLEAR
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for Type B)>DTC CHECK / CLEAR
| Proceed to |
|---|
| DTC B167A or B167E is output |
| DTC B166C or B166F is output |
| DTCs B166C, B166F, B167A and B167E are not output |
Codes other than DTCs B166C, B166F, B167A and B167E may be output at this time, but they are not related to this check.
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Return the side airbag pressure sensor RH and LH to their original positions and connect the connectors to them.
DTC B167A or B167E is output
DTC B166C or B166F is output
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SIDE AIRBAG SENSOR (for Front Door)>REMOVAL
DTCs B166C, B166F, B167A and B167E are not output
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING