| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
| P071531 | Input/Turbine Speed Sensor "A" No Signal | While driving after warm-up with clutch engaged, transmission input speed is not input
(1-trip detection logic) |
·
Harness and connector ·
Transmission revolution sensor ·
ECM |
Does not come on | DTC stored | SAE Code:
P0717 |
| P08051C | Clutch Position Sensor "A" Circuit Voltage Out of Range | While driving after warm-up with clutch engaged, clutch pedal stroke sensor assembly value continuously indicates clutch disengaged
(1-trip detection logic) |
·
Harness and connector ·
Clutch pedal stroke sensor ·
ECM |
Does not come on | DTC stored | SAE Code:
P0806 |
| P081174 | Excessive Clutch "A" Slippage Actuator Slipping | With clutch completely engaged, divergence between transmission input speed and engine speed is continuously greater than threshold
(1-trip detection logic) |
·
Harness and connector ·
Transmission revolution sensor ·
Clutch pedal stroke sensor ·
Clutch slippage ·
ECM |
Does not come on | DTC stored | SAE Code:
P0811 |
After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the ignition switch off and wait for 30 seconds or more.
Turn the ignition switch to ON and turn the GTS on.
Perform the Road Test.
Enter the following menus: Powertrain / Engine and Transmission / Utility / All Readiness.
Input the DTC: P071531, P08051C or P081174.
Check the DTC judgment result.
| GTS Display | Description |
|---|---|
| NORMAL | ·
DTC judgment completed ·
System normal |
| ABNORMAL | ·
DTC judgment completed ·
System abnormal |
| INCOMPLETE | ·
DTC judgment not completed ·
Perform driving pattern after confirming DTC enabling conditions |
| N/A | ·
Unable to perform DTC judgment ·
Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit |
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.
Perform registration and/or initialization when parts related to the iMT system are replaced.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and Transmission / Data List
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Engine Speed | Engine speed | Min.: 0 rpm
Max.: 16383 rpm |
650 to 750 rpm: Idling with warm engine | When the crankshaft position sensor is malfunctioning, "Engine Speed" is approximately 0 rpm or varies greatly from the actual engine speed. |
| NIM Sensor Speed | Input shaft speed (NIM) | Min.: 0 rpm
Max.: 16383 rpm |
Input shaft speed (NIM) equal to engine speed (NE): Clutch pedal not depressed, vehicle running | - |
| Tester Display |
|---|
| Engine Speed |
| NIM Sensor Speed |
When the clutch is engaged, the engine speed is constant and the difference between "Engine Speed" and "NIM Sensor Speed" in the Data List is below 200 rpm.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and Transmission / Data List
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Clutch Stroke Position | Clutch pedal stroke calculated by ECM | Min.: -200%
Max.: 199.9% |
Value increases: Clutch pedal released → clutch pedal fully depressed | - |
| Tester Display |
|---|
| Clutch Stroke Position |
| Result | Proceed to |
|---|---|
| Data display is within Normal Condition range | A |
| Data display is not within Normal Condition range | B |
A
B
| *a | Front view of wire harness connector
(to Clutch Pedal Stroke Sensor Assembly) |
Disconnect the clutch pedal stroke sensor assembly connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| M6-3 (VCSK) - M6-1 (SKG) | Ignition switch ON | 4.5 to 5.5 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the ECM connector.
Disconnect the clutch pedal stroke sensor assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M6-2 (SKS1) - A2-20 (CLS) | Always | Below 1 Ω |
| M6-2 (SKS1) or A2-20 (CLS) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the clutch pedal stroke sensor assembly.
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs.
Turn the ignition switch off and wait for at least 30 seconds.
Perform the Road Test.
Enter the following menus: Powertrain / Engine and Transmission / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| DTC P08051C or P081174 is output | B |
A
B
Disconnect the ECM connector.
Disconnect the clutch pedal stroke sensor assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M6-1 (SKG) - A2-21 (E2CL) | Always | Below 1 Ω |
| M6-3 (VCSK) - A2-23 (VCCL) | Always | Below 1 Ω |
| M6-1 (SKG) or A2-21 (E2CL) - Body ground | Always | 10 kΩ or higher |
| M6-3 (VCSK) or A2-23 (VCCL) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Refer to the "Clutch slips" item in the problem symptoms table for the clutch system and check each part.
Click hereDrivetrain>CLUTCH>CLUTCH SYSTEM>PROBLEM SYMPTOMS TABLE
Inspections of all suspected areas are normal.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | CORRECT |
| *b | INCORRECT |
Check the transmission revolution sensor installation.
The installation bolt is tightened properly and there is no clearance between the sensor and transmission case.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the transmission revolution sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E26-2 (NMB) - E7-12 (NIMB) | Always | Below 1 Ω |
| E26-1 (NMO) - E7-13 (NIMO) | Always | Below 1 Ω |
| E26-2 (NMB) or E7-12 (NIMB) - Body ground | Always | 10 kΩ or higher |
| E26-1 (NMO) or E7-13 (NIMO) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect transmission revolution sensor.
Click hereDrivetrain>RC60J (MANUAL TRANSMISSION / TRANSAXLE)>SPEED SENSOR>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the teeth of the countershaft 2nd speed gear.
No tooth damage on countershaft 2nd speed gear.
| Proceed to |
|---|
| OK |
| NG |
OK
NG