Home › Vehicle Interior › SEAT BELT › REAR SEAT OUTER BELT ASSEMBLY (for Van)
RM35X0E _58 Vehicle Interior _078602 SEAT BELT _0387530 REAR SEAT OUTER BELT ASSEMBLY(for Van) A

SEAT BELT  REAR SEAT OUTER BELT ASSEMBLY(for Van)  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.

·

Use the same procedure for the RH and LH sides.

·

The following procedure is for the LH side.



PROCEDURE

Hide 73370E 1.INSPECT REAR SEAT OUTER BELT ASSEMBLY LH

Hide 73370E 2.INSTALL REAR SEAT OUTER BELT ASSEMBLY LH

a.
B541716N01
2.479,1.167 2.635,1.365 0.156,0.198 10 true A 2.646,1.167 2.865,1.365 0.219,0.198 10 true (1) 1.677,3.063 1.833,3.26 0.156,0.198 10 true B 1.833,3.063 2.052,3.26 0.219,0.198 10 true (2)

Attach the guide.


b.

Temporarily install the rear seat outer belt assembly LH with the 2 bolts.


c.

Tighten the 2 bolts in the order shown in the illustration.

Torque:
Bolt A : 12.5 N*m (127 kgf*cm, 9 ft.*lbf)
Bolt B : 42 N*m (428 kgf*cm, 31 ft.*lbf)


d.
B541715C01
2.302,0.729 2.771,0.979 true 2.104,0.563 2.292,0.771 0.188,0.208 10 false *a
*a Locking Button
V113147

Lock in this Direction


w/ Pretensioner and Force Limiter:

i.

Connect the pretensioner connector and lock the locking button as shown in the illustration.

NOTICE:
·

When handling the pretensioner connector, take care not to damage the pretensioner wire harness.

·

Securely lock the locking button.





e.
B541713

Tighten the bolt.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


f.
B541712C02
0,0 0,0 false
V113147

Close in this Direction


Attach the claw and close the cover as shown in the illustration.


g.
B541710C01
0,0 0,0 false
V113146

Place Hands Here
V113147

Remove in this Direction (1)
V113148

Remove in this Direction (2)


Attach the guide in the installation direction (1) shown in the illustration.


h.

Attach the claw in the installation direction (2) shown in the illustration and install the cover.


i.
B541290

Connect the rear seat outer belt assembly LH.


j.

Check that the ELR locks.

i.

With the rear seat outer belt assembly LH installed to the vehicle, check that the belt locks when it is pulled out quickly.



Hide 3.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL (w/ Front Seat Side Airbag)

Hide 4. INITIALIZATION AFTER RECONNECTING BATTERY TERMINAL (w/ Front Seat Side Airbag)

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


Hide 5. PERFORM DIAGNOSTIC SYSTEM CHECK (w/ Pretensioner and Force Limiter)

Hide 6.CHECK SRS WARNING LIGHT (w/ Pretensioner and Force Limiter)