| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
| P062712 | Fuel Pump "A" Control Circuit Short to Battery | Short in pre-stroke control valve circuit for 0.5 seconds (1 trip detection logic). | ·
Short in pre-stroke control valve circuit ·
Fuel supply pump assembly ·
ECM |
Comes on | DTC stored | SAE Code: P0629 |
| P062714 | Fuel Pump "A" Control Circuit Short to Ground or Open | Open or short in pre-stroke control valve circuit for 0.5 seconds (1 trip detection logic). | ·
Open or short in pre-stroke control valve circuit ·
Fuel supply pump assembly ·
ECM |
Comes on | DTC stored | SAE Code: P0628 |
| DTC No. | Data List |
|---|---|
| P062712
P062714 |
·
Fuel Pressure (High) ·
Target Fuel Pressure (High) |
For more information on the fuel supply pump assembly (pre-stroke control valve) and common rail system, refer to System Description (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>SYSTEM DESCRIPTION).
When DTC P062712 or P062714 is stored, check the internal fuel pressure of the common rail by entering the following menus on the GTS: Powertrain / Engine / Data List / Fuel Pressure (High).
Under a stable operating condition such as idling, Fuel Pressure (High) is within 5000 kPag of Target Fuel Pressure (High).
| DTC No. | DTC Detection Drive Pattern |
|---|---|
| P062712
P062714 |
Idling for 1 second or more |
After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION) and initialization (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>INITIALIZATION).
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Inspect the pre-stroke control valve.
Click hereEngine / Hybrid System>1GD-FTV (FUEL)>FUEL SUPPLY PUMP>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the pre-stroke control valve connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E102-1 (+B) - E6-3 (PCV+) | Always | Below 1 Ω |
| E102-2 (PCV) - E6-4 (PCV-) | Always | Below 1 Ω |
| E102-1 (+B) or E6-3 (PCV+) - Body ground and other terminals | Always | 10 kΩ or higher |
| E102-2 (PCV) or E6-4 (PCV-) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Clear the DTCs.
Start the engine and idle it for 1 second or more.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| No DTC is output | A |
| DTC P062712 or P062714 is output | B |
A
B
Replace the ECM.
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Repair or replace the harness or connector.
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Clear the DTCs.
Turn the ignition switch off for 30 seconds or more.
Start the engine and idle it for 1 second or more.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Confirm that the DTC is not output again.
| Proceed to |
|---|
| NEXT |
NEXT
Replace the fuel supply pump assembly.
Click hereEngine / Hybrid System>1GD-FTV (FUEL)>FUEL SUPPLY PUMP>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Bleed the air from the fuel system.
Click hereEngine / Hybrid System>1GD-FTV (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| NEXT |
NEXT