Home › Engine / Hybrid System › 1GD-FTV (FUEL) › FUEL SUPPLY PUMP › 2019.02–2020.05
RM35X0E _51 Engine / Hybrid System _079306 1GD-FTV FUEL _0385713 FUEL SUPPLY PUMP A

1GD-FTV FUEL  FUEL SUPPLY PUMP  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the fuel supply pump assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)

HINT:

When the cable is disconnected / reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative when not Performed Necessary Procedures Link
Stop and start system Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes). (Click here)
Lane control system Drive the vehicle straight ahead at 15 km/h (10 mph) or more for 1 second or more. (Click here)
Pre-collision system

·

Learning completes when vehicle is operated normally

Effect/Inoperative when not Performed Necessary Procedures Link
Power slide door system Fully close the slide door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the slide door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



NOTICE:
·

When replacing the parts in the following chart (A), replace the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly with new ones.

Replaced Parts (A) Pipes Requiring New Replacement
Injector assembly (including shuffling the injector assemblies between the cylinders)
·

No. 1 injection pipe sub-assembly

·

No. 2 injection pipe sub-assembly


Supply pump assembly Fuel inlet pipe sub-assembly
·

Common rail assembly

·

Cylinder block sub-assembly

·

Cylinder head sub-assembly

·

Timing chain case assembly


·

No. 1 injection pipe sub-assembly

·

No. 2 injection pipe sub-assembly

·

Fuel inlet pipe sub-assembly



·

After removing the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly, clean them with a brush and compressed air.

·

The supply pump assembly is a precision instrument. Do not use the supply pump assembly if it is struck or dropped.

·

Hold the supply pump assembly itself during removal and installation. Do not hold the pre-stroke control valve or fuel pipe, etc.

·

Make sure foreign matter does not enter the fuel path.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Hide 12601B 3.REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY

Hide 51406A 5.REMOVE NO. 2 ENGINE UNDER COVER SUB-ASSEMBLY (w/ No. 2 Engine Under Cover Sub-assembly)

Hide 52618 6.REMOVE LOWER FRONT BUMPER ABSORBER

Hide 51405A 7.REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY

Hide 25761B 9.DISCONNECT NO. 1 VACUUM TRANSMITTING HOSE

Hide 17303T 10.REMOVE AIR PIPE SUB-ASSEMBLY

Hide 16571C 11.REMOVE NO. 1 RADIATOR HOSE

Hide 53106B 12.REMOVE RADIATOR COVER SUB-ASSEMBLY

Hide 17751 13.REMOVE NO. 1 AIR CLEANER INLET

Hide 44360 14.DISCONNECT VANE PUMP OIL RESERVOIR ASSEMBLY

Hide 16470 15.REMOVE RADIATOR RESERVOIR

Hide 88359 16.REMOVE VISCOUS HEATER V BELT (w/ Viscous Heater)

Hide 16711 17.REMOVE FAN SHROUD

Hide 16620 18.REMOVE V-RIBBED BELT TENSIONER ASSEMBLY

Hide 23273H 19.REMOVE NO. 2 FUEL HOSE

a.
A344931

Slide the 2 clips and remove the No. 2 fuel hose from the supply pump assembly and No. 3 nozzle leakage pipe assembly.


Hide 23271H 20.REMOVE NO. 1 FUEL HOSE

a.
A344932

Slide the 2 clips and remove the No. 1 fuel hose from the supply pump assembly and No. 2 fuel pipe.


Hide 21.REMOVE NO. 4 FUEL PIPE (w/ Pressurized Fuel Filter)

a.
A370020

Remove the No. 4 fuel pipe 2 union bolts and 2 gaskets from the supply pump assembly and fuel filter.


Hide 22803 22.REMOVE FUEL INJECTION PUMP COVER SUB-ASSEMBLY

A344933

a.

Remove the fuel injection pump cover sub-assembly from the supply pump assembly.


Hide 23.REMOVE FUEL PUMP MOTOR WIRE

a.
A344934

Disconnect the fuel pump motor wire connector.


b.

Detach the clamp and remove the fuel pump motor wire.


Hide 11324 24.REMOVE TIMING CHAIN COVER PLATE

a.
A344936

Remove the 3 bolts and timing chain cover plate.


b.

Remove the gasket.


Hide 22100 25.REMOVE SUPPLY PUMP ASSEMBLY

NOTICE:
·
A347308C02
0.115,0.104 0.51,0.385 0.396,0.281 12 false *A 0.115,2.542 0.458,2.833 0.344,0.292 12 false *B
*A w/ DPF and Pressurized Fuel Filter
*B w/o Pressurized Fuel Filter


Do not hold the supply pump assembly by the parts indicated by the arrows in the illustration.

·

With SST set, do not turn the crankshaft more than a half rotation.



a.
A349352C01
1.625,2.031 1.625,1.365 true 1.49,2.042 1.49,1.344 true 1.167,2.042 1.625,2.042 true 0.958,1.927 1.271,2.083 0.313,0.156 10 false *a
*a Timing Mark


Align the timing mark of the crankshaft pulley sub-assembly and timing chain cover by rotating the crankshaft clockwise.


b.
A344937C01
0.5,1.51 0.75,1.51 0.75,1.51 0.844,1.698 true 1.271,2.01 1.708,2.01 false 0.708,1.99 1.021,2.146 0.313,0.156 10 false *a 0.177,1.427 0.635,1.625 0.458,0.198 10 true SST 1.75,1.938 2.208,2.135 0.458,0.198 10 true SST
*a Hold
V113147

Turn


Using SST, hold the crankshaft pulley assembly and loosen the fuel supply pump shaft nut.

SST
09213-58014  (91551-80840)
09330-00021  

NOTICE:

Do not excessively loosen the supply pump shaft nut, otherwise SST cannot be installed.


HINT:

Rotate the supply pump shaft nut once to loosen it.



c.
A359572C01
0.031,0.031 0.375,0.302 0.344,0.271 10 true *A 0.073,2.448 0.479,2.688 0.406,0.24 10 true *B
*A w/ DPF and w/ Pressurized Fuel Filter
*B w/o Pressurized Fuel Filter


Loosen the 3 nuts from the supply pump assembly.

NOTICE:

Do not completely remove the nuts. Otherwise, the supply pump assembly may fall off.



d.
A344938E01
1.219,1.552 1.417,1.552 1.417,1.552 1.771,1.313 true 0.865,1.458 1.323,1.656 0.458,0.198 10 true SST

Install SST with 3 bolts.

SST
09241-11010  

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

NOTICE:

Install SST with the bolts included with SST.


HINT:
A454662C01
2.021,3.188 2.74,2.688 2.74,2.688 2.938,2.688 true 0.24,0.135 0.552,0.292 0.313,0.156 10 false *a 0.26,2.479 0.573,2.635 0.313,0.156 10 false *b 2.969,2.594 3.281,2.75 0.313,0.156 10 false *c
*a Engine Front Side
*b Engine Rear Side
*c SST Hexagonal Portion


·

Make sure that the installation direction of SST is as shown in the illustration.

·

Align the hexagonal portion of SST with the supply pump shaft nut to install SST.




e.
A438489

Remove the 2 bolts and No. 1 fuel pump bracket from the supply pump assembly and cylinder block sub-assembly.


f.
A344939C01
0.573,1.333 0.802,1.333 0.802,1.333 1.031,1.563 true 1.708,1.854 2.167,1.854 false 2.438,0.813 2.615,1.125 2.615,1.125 2.802,1.125 true 0.969,1.948 1.281,2.104 0.313,0.156 10 false *a 2.813,1.031 3.271,1.229 0.458,0.198 10 true SST 2.198,1.781 2.656,1.979 0.458,0.198 10 true SST 0.25,1.271 0.708,1.469 0.458,0.198 10 true SST
*a Hold
V113147

Turn


Install the handle to SST. While holding the crankshaft pulley assembly in place with the crankshaft holding tool, turn the handle in the counterclockwise direction to disconnect the supply pump assembly.

SST
09213-58014  (91551-80840)
09330-00021  
09241-11010  


g.

Remove the 3 nuts and supply pump assembly from the timing chain case assembly.


h.
A347064

Remove the O-ring from the supply pump assembly.