Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/o EGR Cooler)
RM35X0E _51 Engine / Hybrid System _078856 1GD-FTV ENGINE CONTROL _0388652 ECD SYSTEM(w/o EGR Cooler) C

1GD-FTV ENGINE CONTROL  ECD SYSTEM(w/o EGR Cooler)  P008700  Fuel Rail / System Pressure - Too Low  P019011  Fuel Rail Pressure Sensor "A" Circuit Short to Ground  P019015  Fuel Rail Pressure Sensor "A" Circuit Short to Battery or Open  P107A11  Fuel Rail Pressure Sensor (Low) / Fuel Rail Pressure Sensor "B" Circuit Short to Ground  P107A15  Fuel Rail Pressure Sensor (Low) / Fuel Rail Pressure Sensor "B" Circuit Short to Battery or Open  


DESCRIPTION

The ECM monitors the internal fuel pressure of the common rail assembly using the fuel pressure sensor, and controls the pre-stroke control valve to regulate the internal pressure so that it reaches the target pressure. The pressure sensor is a semiconductor that varies electrical resistance when pressure is applied to its silicon chip. This sensor outputs a voltage in proportion to the internal fuel pressure.

A208460E74
2.781,0.51 2.938,0.365 2.938,0.365 3.135,0.365 false 2.771,2.125 3,1.885 3,1.885 3.188,1.885 false 1.948,1.646 2.177,1.646 false 2.229,1.104 2.5,1.104 false 1.406,0.531 0.938,0.646 false 0.063,0.042 1.792,0.271 1.729,0.229 10 false Property of Output Voltage: 1.052,0.406 1.417,0.594 0.365,0.188 10 false 5.00 0.625,0.573 0.948,0.813 0.323,0.24 10 false 4.90 2.208,1.573 2.958,1.844 0.75,0.271 10 false RR2 (Sub) 1.542,1.021 2.198,1.271 0.656,0.25 10 false RR (Main) 1.052,0.625 1.49,0.813 0.438,0.188 10 false 4.61 1.052,0.823 1.406,1.021 0.354,0.198 10 false 4.11 1.052,1.708 1.417,1.917 0.365,0.208 10 false 1.35 1.052,1.906 1.385,2.073 0.333,0.167 10 false 0.85 1.052,2.083 1.427,2.25 0.375,0.167 10 false 0.55 1.24,2.219 1.417,2.406 0.177,0.188 10 false 0 2.938,2.333 3.604,2.573 0.667,0.24 10 false 233000 1.667,2.51 3.01,2.792 1.344,0.281 10 false Fuel Pressure (kPag) 3.24,1.802 4.5,2.333 1.26,0.531 10 false Stores P019011 or P107A11 3.198,0.271 4.448,0.833 1.25,0.563 10 false Stores P019015 or P107A15 0.063,1.115 1.25,1.406 1.188,0.292 10 false Output Voltage (V) 5.198,1.177 5.656,1.438 0.458,0.26 10 false Main 5.26,1.917 5.604,2.135 0.344,0.219 10 false Sub 6.729,1.177 7.156,1.365 0.427,0.188 10 false PCR1 6.74,1.375 7.104,1.563 0.365,0.188 10 false E2M 6.74,1.74 7.125,1.969 0.385,0.229 10 false VCS 6.729,1.938 7.146,2.156 0.417,0.219 10 false PCR2 5.875,0.625 6.365,0.833 0.49,0.208 10 false VCM 6.375,2.438 6.75,2.677 0.375,0.24 10 false E2S 4.448,0.042 6.958,0.542 2.51,0.5 10 false Internal Structure of the Pressure Sensor (Duplicate Systems):

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P008700 Fuel Rail / System Pressure - Too Low Fuel pressure sensor output voltage stays at fixed value a certain number of times (0.1 seconds or more) (1 trip detection logic).
·

Open or short in fuel pressure sensor circuit

·

Fuel pressure sensor (common rail assembly)

·

Ran out of fuel

·

Fuel frozen


Comes on DTC stored SAE Code: P0087
P019011 Fuel Rail Pressure Sensor "A" Circuit Short to Ground Fuel pressure sensor output voltage (main) is 0.55 V or less for 0.5 seconds (1 trip detection logic).
·

Short in fuel pressure sensor circuit

·

Fuel pressure sensor (common rail assembly)

·

ECM


HINT:

Trouble areas are related to the electrical system only (pumps are not involved)


Comes on DTC stored SAE Code: P0192
P019015 Fuel Rail Pressure Sensor "A" Circuit Short to Battery or Open Fuel pressure sensor output voltage (main) is 4.9 V or higher for 0.5 seconds (1 trip detection logic).
·

Open or short in fuel pressure sensor circuit

·

Fuel pressure sensor (common rail assembly)

·

ECM


HINT:

Trouble areas are related to the electrical system only (pumps are not involved)


Comes on DTC stored SAE Code: P0193
P107A11 Fuel Rail Pressure Sensor (Low) / Fuel Rail Pressure Sensor "B" Circuit Short to Ground Fuel pressure sensor output voltage (sub) is 0.55 V or less for 0.5 seconds (1 trip detection logic).
·

Short in fuel pressure sensor circuit

·

Fuel pressure sensor (common rail assembly)

·

ECM


HINT:

Trouble areas are related to the electrical system only (pumps are not involved)


Comes on DTC stored SAE Code: P107C
P107A15 Fuel Rail Pressure Sensor (Low) / Fuel Rail Pressure Sensor "B" Circuit Short to Battery or Open Fuel pressure sensor output voltage (sub) is 4.9 V or higher for 0.5 seconds (1 trip detection logic).
·

Open or short in fuel pressure sensor circuit

·

Fuel pressure sensor (common rail assembly)

·

ECM


HINT:

Trouble areas are related to the electrical system only (pumps are not involved)


Comes on DTC stored SAE Code: P107D

Related Data List
DTC No. Data List
P008700
P019011
P019015
P107A11
P107A15
·

Target Fuel Pressure (High)

·

Fuel Pressure (High)

·

Fuel Pressure (Low) / Fuel Pressure 2



HINT:
·

Check Fuel Pressure (High) and compare it to Target Fuel Pressure (High) in the Data List by entering the following menus: Powertrain / Engine / Data List / Fuel Pressure (High), Target Fuel Pressure (High). Under stable conditions, the difference between Fuel Pressure (High) and Target Fuel Pressure (High) is 5000 kPag or less.

·

For more information on the fuel pressure sensor and common rail system, refer to System Description (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o EGR Cooler)>SYSTEM DESCRIPTION).

·

If DTC P008700 is stored, the following symptoms may appear:

-

Black smoke

-

Poor drivability

-

Lack of power

-

Lack of power due to accelerator restriction performed by fail-safe function


·

If DTC P019011, P019015, P107A11 and/or P107A15 is stored, the following symptom may appear:

-

Lack of power due to accelerator restriction performed by fail-safe function


·

If DTC P019011, P019015, P107A11 and/or P107A15 is stored, "Fuel Pressure (High)" always displays 0 kPag or 240000 kPag.



CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P008700 After idling for 60 seconds, quickly increase engine speed to 2500 rpm repeatedly for 30 seconds
P019011
P019015
P107A11
P107A15
Ignition switch ON for 1 second or more

MONITOR DESCRIPTION

P008700 (Fuel pressure sensor output stays at fixed value):
·

Under normal conditions, the internal fuel pressure of the common rail assembly usually fluctuates by 1000 to 2000 kPag (10 to 20 kgf/cm2, 145 to 290 psi) even when driving conditions are constant. This DTC is stored if there is no fluctuation of the fuel pressure. The internal fuel pressure is approximately 30000 to 50000 kPag (305.9 to 509.9 kgf/cm2, 4350 to 7250 psi) when idling, and it increases to approximately 65000 to 110000 kPag (662.8 to 1121.7 kgf/cm2, 9425 to 15950 psi) when running the engine at 3000 rpm.

If this DTC is stored, the ECM enters fail-safe mode and limits engine power. The ECM continues operating in fail-safe mode until the ignition switch is turned off.

·

The diagram below indicates that fuel pressure rises as engine speed increases, but for the malfunction indicated by this DTC, that does not happen.

A175676E29
4.99,0.885 5.458,0.521 5.458,0.521 5.615,0.521 false 4.802,1.771 4.677,1.771 4.677,1.771 4.188,1.427 false 0.063,0.031 2.375,0.302 2.313,0.271 10 false P008700 Malfunction Detection 2.271,0.552 3.229,0.771 0.958,0.219 10 false Fuel Pressure 4.844,1.677 5.51,1.875 0.667,0.198 10 false Abnormal 5.656,0.427 6.24,0.625 0.583,0.198 10 false Normal 2.292,2.156 3.302,2.417 1.01,0.26 10 false Engine Speed 5.229,3.375 5.635,3.583 0.406,0.208 10 false Time

·

Even when the system is normal, DTCs may be stored due to a drop in fuel pressure as a result of the vehicle running out of fuel.

When P008700 and vehicle control history code X0806 are stored at the same time, clear the DTCs and check for DTCs once more.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o EGR Cooler)>VEHICLE CONTROL HISTORY



P019011, P019015, P107A11 and P107A15 (Open or short in fuel pressure sensor circuit):

These DTCs are stored if the fuel pressure sensor output voltage is out of the standard range due to an open or short malfunction of the sensor circuit.

If these DTCs are stored, the ECM enters fail-safe mode and limits the engine power. The ECM continues operating in fail-safe mode until the ignition switch is turned off.


WIRING DIAGRAM

A348536E16
0.469,3.083 1.135,3.271 0.667,0.188 10 false E105 0.448,3.271 1.938,3.521 1.49,0.25 10 false Fuel Pressure Sensor 1.698,0.531 2.01,0.729 0.313,0.198 10 false PR 1.719,0.958 2.031,1.156 0.313,0.198 10 false E2 1.698,1.385 2.01,1.583 0.313,0.198 10 false VC 1.635,1.792 1.948,1.99 0.313,0.198 10 false PR2 1.604,2.219 1.917,2.417 0.313,0.198 10 false E2S 1.979,2.76 2.292,2.958 0.313,0.198 10 false 1 5.281,0.542 5.594,0.74 0.313,0.198 10 false E7 5.594,0.656 6.146,0.854 0.552,0.198 10 false PCR1 5.594,1.083 5.906,1.281 0.313,0.198 10 false E2M 5.604,1.5 6.063,1.708 0.458,0.208 10 false VCM 5.594,1.906 6.083,2.094 0.49,0.188 10 false PCR2 5.604,2.323 5.917,2.521 0.313,0.198 10 false E2S 1.604,2.646 1.917,2.844 0.313,0.198 10 false VCS 5.583,2.75 5.896,2.948 0.313,0.198 10 false VCS 5.281,0.958 5.594,1.156 0.313,0.198 10 false E7 5.281,1.375 5.594,1.573 0.313,0.198 10 false E7 5.271,1.802 5.583,2 0.313,0.198 10 false E8 5.271,2.219 5.583,2.417 0.313,0.198 10 false E8 5.292,2.635 5.604,2.833 0.313,0.198 10 false E8 5.938,3.073 6.427,3.271 0.49,0.198 10 false ECM 1.99,1.917 2.302,2.115 0.313,0.198 10 false 2 1.99,2.333 2.302,2.531 0.313,0.198 10 false 3 1.979,1.083 2.292,1.281 0.313,0.198 10 false 4 1.979,0.656 2.292,0.854 0.313,0.198 10 false 5 1.979,1.5 2.292,1.698 0.313,0.198 10 false 6 5.292,0.344 5.604,0.542 0.313,0.198 10 false 18 5.292,0.76 5.604,0.958 0.313,0.198 10 false 19 5.292,1.188 5.604,1.385 0.313,0.198 10 false 28 5.292,1.615 5.604,1.813 0.313,0.198 10 false 23 5.292,2.021 5.604,2.219 0.313,0.198 10 false 21 5.292,2.438 5.604,2.635 0.313,0.198 10 false 22

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o EGR Cooler)>REGISTRATION) and initialization (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o EGR Cooler)>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Trouble Codes.


d.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
DTC P019011, P019015, P107A11 or P107A15 is output A
DTC P008700 is output* B



HINT:

*: When P008700 and vehicle control history code X0806 are stored, they may be stored as a result of a drop in fuel pressure due to the vehicle running out of fuel. Therefore, clear the DTCs and check that the DTCs are not stored again.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o EGR Cooler)>VEHICLE CONTROL HISTORY



A

2.CHECK ECM (FUEL PRESSURE SENSOR VOLTAGE)

B

8.REPLACE COMMON RAIL ASSEMBLY
2.CHECK ECM (FUEL PRESSURE SENSOR VOLTAGE)
a.
A372026C51
1.219,0.833 1.635,1.083 0.417,0.25 1.74,0.833 2.156,1.083 0.417,0.25 0.865,2.313 1.615,1.646 true 1.438,2.354 1.667,1.688 true 2.031,2.344 1.948,1.635 true 2.615,2.333 2,1.646 true 1.313,0.875 1.771,1.073 0.458,0.198 10 false E7 1.833,0.865 2.292,1.063 0.458,0.198 10 false E8 0.448,2.427 1.094,2.615 0.646,0.188 10 false 19 (E2M) 1.104,2.427 1.792,2.635 0.688,0.208 10 false 28 (VCM) 1.771,2.427 2.458,2.635 0.688,0.208 10 false 22 (VCS) 2.469,2.427 3.115,2.604 0.646,0.177 10 false 21 (E2S) 0.094,0.063 0.406,0.26 0.313,0.198 10 false *a
*a Component with harness connected
(ECM)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
E7-28 (VCM) - E7-19 (E2M) Ignition switch ON 4.5 to 5.5 V
E8-22 (VCS) - E8-21 (E2S) Ignition switch ON 4.5 to 5.5 V



Result:
Proceed to
OK
NG



OK

3.INSPECT FUEL PRESSURE SENSOR (PCR1, PCR2 VOLTAGE)

NG

11.REPLACE ECM
3.INSPECT FUEL PRESSURE SENSOR (PCR1, PCR2 VOLTAGE)
a.
A372026C52
1.219,0.833 1.635,1.083 0.417,0.25 1.74,0.833 2.156,1.083 0.417,0.25 0.771,2.406 1.615,1.646 true 1.479,2.729 1.656,1.635 true 2.073,2.406 1.948,1.635 true 2.75,2.729 2.042,1.635 true 1.313,0.875 1.771,1.073 0.458,0.198 10 false E7 1.833,0.875 2.292,1.073 0.458,0.198 10 false E8 0.448,2.427 1.094,2.615 0.646,0.188 10 false 19 (E2M) 1.156,2.75 1.844,2.958 0.688,0.208 10 false 18 (PCR1) 1.771,2.427 2.458,2.635 0.688,0.208 10 false 23 (PCR2) 2.552,2.75 3.198,2.927 0.646,0.177 10 false 21 (E2S) 0.094,0.063 0.406,0.26 0.313,0.198 10 false *a
*a Component with harness connected
(ECM)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
E7-18 (PCR1) - E7-19 (E2M) Idling 1.8 to 2.1 V
E8-23 (PCR2) - E8-21 (E2S) Idling 1.3 to 1.6 V



Result:
Proceed to
OK
NG



OK

4.CHECK WHETHER DTC OUTPUT RECURS

NG

5.CHECK ECM (FUEL PRESSURE SENSOR VOLTAGE)
4.CHECK WHETHER DTC OUTPUT RECURS
a.

Turn the ignition switch to ON.


b.

Connect the GTS to the DLC3.


c.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

d.

Turn the ignition switch off for 30 seconds or more.


e.

Turn the ignition switch to ON for 1 second or more.


f.

Enter the following menus: Powertrain / Engine / Trouble Codes.


g.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
DTC P019011, P019015, P107A11 or P107A15 is output A
DTC is not output B




B

A

11.REPLACE ECM
5.CHECK ECM (FUEL PRESSURE SENSOR VOLTAGE)
a.
A204375C36
0.563,1.135 0.948,1.375 0.385,0.24 1.073,0.781 1.427,1.052 true 1.094,1.615 1.417,1.323 true 2.323,1.5 1.958,1.323 true 1.938,1.031 2.271,0.729 true 0.75,0.667 1.115,0.865 0.365,0.198 10 false VCS 0.604,1.167 1.406,1.625 0.802,0.458 10 false E105 2.313,0.646 2.771,0.844 0.458,0.198 10 false E2S 0.885,1.615 1.26,1.802 0.375,0.188 10 false E2 2.365,1.49 2.833,1.698 0.469,0.208 10 false VC 0.167,0.146 0.479,0.344 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to Fuel Pressure Sensor)


Disconnect the fuel pressure sensor connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
E105-6 (VC) - E105-4 (E2) Ignition switch ON 4.5 to 5.5 V
E105-1 (VCS) - E105-3 (E2S) Ignition switch ON 4.5 to 5.5 V



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (FUEL PRESSURE SENSOR - ECM)

NG

12.REPAIR OR REPLACE HARNESS OR CONNECTOR
6.CHECK HARNESS AND CONNECTOR (FUEL PRESSURE SENSOR - ECM)
a.

Disconnect the fuel pressure sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E105-5 (PR) - E7-18 (PCR1) Always Below 1 Ω
E105-4 (E2) - E7-19 (E2M) Always Below 1 Ω
E105-2 (PR2) - E8-23 (PCR2) Always Below 1 Ω
E105-3 (E2S) - E8-21 (E2S) Always Below 1 Ω
E105-5 (PR) or E7-18 (PCR1) - Body ground and other terminals Always 10 kΩ or higher
E105-2 (PR2) or E8-23 (PCR2) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.CHECK ECM (CHECK RESISTANCE)

NG

12.REPAIR OR REPLACE HARNESS OR CONNECTOR
7.CHECK ECM (CHECK RESISTANCE)
a.

Disconnect the fuel pressure sensor connector.


b.
A204375C37
0.563,1.135 0.948,1.375 0.385,0.24 1.073,0.781 1.427,1.052 true 1.094,1.615 1.417,1.323 true 2.281,1.625 1.958,1.323 true 1.938,1.031 2.271,0.729 true 1.708,1 1.896,0.365 1.896,0.365 2.042,0.365 true 1.646,1.844 1.521,1.844 1.521,1.844 1.688,1.344 true 0.75,0.667 1.115,0.865 0.365,0.198 10 false VCS 0.604,1.167 1.115,1.438 0.51,0.271 10 false E105 2.302,0.667 2.76,0.865 0.458,0.198 10 false E2S 0.885,1.615 1.26,1.802 0.375,0.188 10 false E2 2.333,1.625 2.802,1.833 0.469,0.208 10 false VC 0.167,0.146 0.479,0.344 0.313,0.198 10 false *a 1.708,1.781 2.083,1.969 0.375,0.188 10 false PR 2.094,0.292 2.552,0.49 0.458,0.198 10 false PR2
*a Front view of wire harness connector
(to Fuel Pressure Sensor)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
E105-6 (VC) - E105-5 (PR) Ignition switch off No short or no open circuit
E105-5 (PR) - E105-4 (E2) Ignition switch off No short or no open circuit
E105-1 (VCS) - E105-2 (PR2) Ignition switch off No short or no open circuit
E105-2 (PR2) - E105-3 (E2S) Ignition switch off No short or no open circuit



Result:
Proceed to
OK
NG



OK

8.REPLACE COMMON RAIL ASSEMBLY

NG

11.REPLACE ECM
8.REPLACE COMMON RAIL ASSEMBLY
a.

Replace the common rail assembly.

Click hereEngine / Hybrid System>1GD-FTV (FUEL)>COMMON RAIL>REMOVAL


Result:
Proceed to
NEXT



NEXT

9.BLEED AIR FROM FUEL SYSTEM
9.BLEED AIR FROM FUEL SYSTEM
a.

Bleed the air from the fuel system.

Click hereEngine / Hybrid System>1GD-FTV (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION


Result:
Proceed to
NEXT



NEXT

10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

c.

Turn the ignition switch off for 30 seconds or more.


d.

Turn the ignition switch to ON.


e.

Let the engine idle for 60 seconds, and then quickly increase the engine speed to 2500 rpm repeatedly for 30 seconds.


f.

Confirm that the DTC is not output again.

HINT:

Perform the following procedure using the GTS to determine whether or not the DTC judgment has been carried out.


i.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

Powertrain > Engine > Utility
Tester Display
All Readiness
50005 372 20

ii.

Input DTC P008700, P019011, P019015, P107A11 or P107A15.


iii.

Check that STATUS is NORMAL. If STATUS is INCOMPLETE, increase the idling time.



Result:
Proceed to
NEXT



NEXT

END

11.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
12.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED