Refer to DTC P03402A.
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o EGR Cooler)>P03402A
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
| P034011 | Camshaft Position Sensor "A" Bank 1 or Single Sensor Circuit Short to Ground | Output voltage of camshaft position sensor is less than 0.3 V for 4 seconds or more (1 trip detection logic). | ·
Camshaft position sensor ·
Open or short in camshaft position sensor circuit ·
ECM |
Comes on | DTC stored | SAE Code: P0342 |
| P034015 | Camshaft Position Sensor "A" Bank 1 or Single Sensor Circuit Short to Battery or Open | Output voltage of camshaft position sensor is higher than 4.7 V for 4 seconds or more (1 trip detection logic). | ·
Camshaft position sensor ·
Open or short in camshaft position sensor circuit ·
ECM |
Comes on | DTC stored | SAE Code: P0343 |
If DTC P034011 or P034015 is stored, the following symptoms may appear:
Difficulty starting
Misfire
Combustion noise
Black smoke
White smoke
Lack of power
Reference: Inspection using an oscilloscope.
The correct waveform is as shown.
| ECM Terminal Name | Between G2+ and G2-
Between NE+ and NE- |
| Tester Range | 2 V/DIV., 20 msec./DIV. |
| Condition | Idling with warm engine |
When the sensor output voltage remains at less than 0.3 V, or higher than 4.7 V for 4 seconds, the ECM stores a DTC.
| DTC No. | DTC Detection Drive Pattern |
|---|---|
| P034011
P034015 |
Ignition switch ON for 4 seconds or more |
Refer to DTC P03402A.
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o EGR Cooler)>P03402A
After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o EGR Cooler)>REGISTRATION) and initialization (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o EGR Cooler)>INITIALIZATION).
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Record any output DTC(s).
Clear the DTCs.
Turn the ignition switch off for 30 seconds or more.
Disconnect the camshaft position sensor connector.
Turn the ignition switch to ON for 4 seconds or more.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Check whether the DTC changes when the connector is disconnected and connected.
| Result | Proceed to |
|---|---|
| DTC does not change | A |
| DTC changes | B |
A
B
| *a | Component with harness connected
(ECM) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| E8-17 (VCG) - E8-18 (G2-) | Ignition switch ON | 4.5 to 5.5 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the camshaft position sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E79-1 (G22+) - E8-27 (G2+) | Always | Below 1 Ω |
| E79-2 (G22-) - E8-18 (G2-) | Always | Below 1 Ω |
| E79-1 (G22+) or E8-27 (G2+) - Body ground and other terminals | Always | 10 kΩ or higher |
| E79-2 (G22-) or E8-18 (G2-) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the camshaft position sensor connector.
| *a | Front view of wire harness connector
(to Camshaft Position Sensor) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| E79-3 (VC) - E79-1 (G22+) | Ignition switch off | No short or no open circuit |
| E79-1 (G22+) - E79-2 (G22-) | Ignition switch off | No short or no open circuit |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the camshaft position sensor.
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>CAMSHAFT POSITION SENSOR>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Repair or replace the harness or connector.
| Proceed to |
|---|
| NEXT |
NEXT
Replace the ECM.
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs.
Turn the ignition switch off for 30 seconds or more.
Turn the ignition switch to ON for 4 seconds or more.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Confirm that the DTC is not output.
| Proceed to |
|---|
| NEXT |
NEXT